Axiom SW215FA User manual

USER MANUAL
SW215FA
acve subwoofer
KEY FEATURES
• Very High Output • Manifolded Transmission Line configuraon for very fast transient response
• Compact size for a very good output-to-weight rao • 96KHz / 40 bit floang point CORE processing with PRONET remote control
• Digitally controlled Class D amplifier module with SMPS • Flying vercal arrayable version
INTRODUCTION
The SW215FA subwoofer is designed to deliver high quality low frequency reproducon where
very high output is a key requirement, together with well defined deep bass response and fast
transient response. Its compact size and light weight make it suitable for several different uses,
ranging from touring applicaons to fixed installaons and high-level dance clubs.
The SW215FA is a very high quality powered subwoofer system featuring some of the most
advanced technologies for low frequency reproducon. Its unique and innovave design is based
on a configuraon that can be defined as Manifolded Transmission Line.
It uses manifolding of the front side of the cones to maximize the mutual coupling between the
two drivers, while loading the back of the cone with a large-size transmission line that has the
funcon to create a transmission path from the back of the transducers to the front.
The SW215FA subwoofer system is equipped with two high power 15” (380mm) transducers
capable of long excursion (up to 33mm peak-to-peak), controlled by high sffness Double Silicon
Spider as centering suspension and by heavy duty surround. The motor structure features high
strength (BL²/Re) with opmized symmetry and excursion controlled by Aluminium Demodulang
Ring. The robust copper 75mm (3”) voice coil is wounded in two different layers both outside and
inside the coil support, then doubling the coil surface exposed to air cooling and consequently
improving the long term thermal capacity of the loudspeaker. Cones are made of very high-sffness
reinforced paper, featuring also invisible water repellent treatment.
The SW215FA is processed by 40bit, 96kHz floang point CORE DSP and powered by DA SERIES digital power modules, a new generaon of CLASS
D power amplifier with digitally-controlled SMPS. The DA module employed for powering the SW215FA delivers in an ultra-compact package a
maximum power of 2000W.
TECHNICAL SPECIFICATION
AcousƟcal Amplifier Type Class D with Variable Switching Frequency
and SMPS
System type Manifolded Band Pass
Transducer
Two 15” (380 mm), 3” (75 mm) VC,
High sffness water repellent reinforced
cone, Flux Demodulang Ring VC,
Double Centering Spider Suspension
Mains Voltage Range (Vac) 230 V~ ±15% or 115 V~ ±15% 50/60 Hz
Mains Connector PowerCon® (NAC3MPA + NAC3MPB)
Consumpon* 700 W (nominal) 1700 W (max)
IN / OUT Connectors Neutrik XLR-M / XLR-F
IN / OUT Network Connectors ETHERCON® (NE8FAV)
Frequency response (±3 dB) 39 Hz – 100 Hz (Processed) Mechanical
Maximum Peak SPL @ 1m 139 dB Width 571 mm (22.48”)
Electrical Height 800 mm (31.50”)
Input Impedance 20 kΩbalanced Depth 582 mm (22.91”)
Input Sensivity +4 dBu / 1.25 V Depth Including Wheels 710 mm (27.95”)
Signal Processing CORE processing, 96kHz / 40bit floang
point SHARC DSP, 24 bit AD/DA converters
Construcon 15 mm, reinforced Phenolic Birch
Paint High resistance, water based paint
Direct access Controls 4 Presets: Standard, InfraSub, Cardioid,
User. Network Terminaon, GND Link
Wheels 4 heavy-load 100 mm ø
Transport 4 handles
Remote Controls PRONET control soware Side Suspension High Strength Steel with ¼ Fast Pin
Network protocol CANBUS Back Suspension High Strength Steel with ¼ Fast Pin
Output Power 1000 W + 1000 W Net Weight 68.5 Kg (151 lb)
* Nominal consumpon is measured with pink noise with a crest factor of 12
dB, this can be considered a standard music program.

MECHANICAL DRAWING
OPTIONAL ACCESSORIES
NAC3FCA Neutrik Powercon® BLUE PLUG USB2CAN PRONET network converter
NAC3FCB Neutrik Powercon® WHITE PLUG KPTSW215 Fly bar for Axiom AX2065 and SW215 Loudspeakers
NE8MCB Neutrik Ethercon PLUG DHSS10M20 Sub-Speaker ø35mm Pole with M20 screw
NC3MXXBAG Neutrik XLR-M RAINCOV215 Rain cover for input sockets
NC3FXXBAG Neutrik XLR-F AXFEETKIT Kit made of 6pcs BOARDACF01 foot
AX2065A Acve vercal array loudspeaker
see hƩp://www.axiomproaudio.com/ for detailed descripon and other available accessories.
SPARE PARTS
AC103GS 100 mm Swivel castor without brake
AC115DN Black steel handle
98AXM215SW8 15’’ woofer - 3” VC - 8 ohm
NAC3MPA Neutrik Powercon® BLUE SOCKET
91AMDSW215 Amplifier module assembly
94SPI2265 Locking Pin for AX2265
80 cm
31.50"
57.1 cm
22.48"
58.2 cm
22.91"
71.0 cm
27.95"
F
F
F
F
F
F
F
F
F
F
F = flying points
P = M20 insert for DHSS10M20
pole adaptor for convenƟonal
SUB-SAT system.
P

I/O AND CONTROL OPERATIONS
MAINS IN - Powercon® NAC3FCA power input connector (blue). To switch the amplifier on, insert the Powercon®
connector and turn it clockwise into the ON posion. To switch the amplifier off, pull back the switch on the connector
and turn it counter-clockwise into the POWER OFF posion.
WARNING! In the case of product failure or fuse replacement, disconnect the unit completely from the mains
power. The power cable must only be connected to a socket corresponding to the specificaons indicated on
the amplifier unit. The power supply must be protected by a suitably rated thermo-magnec breaker. Preferably
use a suitable switch to power on the whole audio system leaving the Powercon® always connected to each
speaker, this simple trick extend the life of the Powercon® connectors.
MAINS OUT - Powercon® NAC3FCB power output connector (grey). This is connected in parallel with the MAINS ~
/ IN. The maximum load applicable depends on the mains voltage. With 230V~ we suggest to link a maximum of 4
SW215FA loudspeakers, with 120V~ we suggest to link at maximum of 2 SW215FA loudspeaker.
ON - This LED indicates power on status.
PROT - This red LED lights when the amplifier module is
in protect mode for an internal fault and, consequently,
the amplifier is muted.
SIGN LIMIT - This LED lights in green to indicate the
presence of the signal and lights in red when an internal
limiter reduces the input level.
INPUT - Audio signal input with locking XLR connector. It
has a fully electronically balanced circuitry including AD
conversion for the best S/N rao and input headroom.
LINK - A direct connecon from the input connector to
link other speakers with same audio signal.
GND LIFT - This switch lithe ground of the balanced
audio inputs from the earth-ground of the amplifier
module.
PRESET BUTTON - This buon has two funcon:
1) Pressing it while powering on the unit:
ID ASSIGN the internal DSP assigns a new ID
to the unit for the PRONET remote
control operaon. Each loudspeaker
must have a unique ID to be visible in
the PRONET network. When you assign
a new ID, all the other loudspeakers
with the ID already assigned must be
ON and connected to the network.
2) Pressing it with the unit ON you can select the DSP PRESET. The selected PRESET is indicated by the corresponding LED:
STANDARD This PRESET is suitable for any applicaon where low frequency reinforcement is required. It features a 90Hz cut offfrequency
and it can be used in almost any environment in combinaon with any vercal arrays.
INFRA This PRESET can be used when a deeper bass response is required (Note that when this preset is used the sound pressure level
of the system is slightly reduced). NOTE: INFRA and STANDARD PRESET must NOT be used together in close units.
CARDIOID This special PRESET, combined with the STANDARD PRESET, gives the advantage to reduce the low frequencies at the back of
an array of three subs, in order to obtain a more comfortable level for the performers on the stage without losing level for the
the audience in front of the array. The cardioid configuraon is also useful in situaon where you want to reduce the bass
frequency feedback due to many microphones on stage, for example for acousc and jazz ensemble, classic orchestra, musicals.
Further in this manual you can find some example how to set up a cardioid array.
USER This LED lights when the USER PRESET is loaded. This preset corresponds to USER MEMORY no. 1 of the DSP and, as a factory
seng, it’s the same to STANDARD. If you want to modify it, you have to connect the unit to a PC, edit the parameters with
PRONET soware and save the PRESET into USER MEMORY no. 1.
NETWORK IN/OUT - These are a standard RJ45 CAT5 connectors (with oponal NEUTRIK NE8MC RJ45 cable connector carrier), used for PRONET
network transmission of remote control data over long distance or mulple unit applicaons.
TERMINATE - In a PRONET network the last loudspeaker device must be terminated (with an inner load resistance) especially in a long run cabling:
press this switch if you want to terminate the unit.

POWER AMPLIFIERS
The SW215FA is powered by DA SERIES digital power modules, a new generaon of CLASS D power amplifier with digitally-controlled SMPS.
The innovave technology used for these amplifiers (including also the use of a variable switching frequency) offers performances at the top of
the range, such as a superior sound definion at any audio frequency, very high dynamics also for low level signals and very low distoron even at
the maximum power The superior sound quality can be compared with top-of-the-range AB-class analog systems, while the DA modules feature a
higher dynamics, very compact size and light weight and efficiency above 90%. The two DA modules employed for powering the SW215FA deliver
in an ultra-compact package a maximum power of 2000W.
SIGNAL PROCESSING
The system processing is based on the CORE DSP plaorm, which has been designed by the PROEL R&D Laboratories using one of the most
advanced SHARC DSP for audio applicaon. It features 40bit, 96kHz floang point resoluon and high quality 24bit AD/DA converters, for a perfect
signal integrity, a dynamic range in excess of 110dB and a superior sonic performance. Thanks to its massive processing power, the CORE plaorm
is capable of providing the most sophiscated algorithms for speaker processing, together with remote control and networking capability.
The PRONET control soware, working on a solid and reliable CANBUS based network protocol, provides an intuive interface for the remote
control of the whole system, with the possibility of eqing, delaying, increasing the protecons and monitoring the status of the amplifier.
PRONET
PRONET soware has been developed in collaboraon with sound engineers and sound designers, in order to offer an “easy-to-use” tool to setup
and manage your audio system. With PRONET you can visualize signal levels, monitor internal status and edit all the parameters of each connected
device.
Download the PRONET app from the AXIOM website at hƩp://www.axiomproaudio.com/ clicking on downloads secƟon of the product.
The AXIOM acve loudspeaker devices can be connected using the network connecon, in this case the PROEL USB2CAN converter oponal
accessory is needed. The first me you connect a device with the USB2CAN converter, Windows O.S. will ask you to install the driver files, which
you can find in the Driver folder within the Pronet applicaon folder (by default is C:\Program Files\Proel\Pronet\Driver, or if you changed it <your
path>\Driver). Please refer also to “Installaon” and “Drivers” paragraphs in the Pronet documentaon.
The PRONET NETWORK is based on a robust, reliable and fast communicaon protocol called CANBUS. The devices in a PRONET NETWORK are
connected together with a “linear bus topology”. The USB2CAN converter must be connected to the network input of the first device, the network
output of the first device is connected to the input of the second and so on. For the network connecons simple RJ45 cat.5 or cat.6 ethernet
cables can be used (please don’t confuse a ethernet network with a PRONET network these are completely different and must be fully separated
also both use the same kind of cable).
The beginning and the end of a PRONET NETWORK must be terminated. One side is terminated by the USB2CAN converter, the other side must
be terminated pressing the TERMINATE switch on the last device. All devices between these two points must have the TERMINATE switch lied.
Assign the ID number
To work properly in a PRONET network each connected device must have a unique idenfier number, called ID. By default the USB2CAN PC
controller has ID=0 and there can be only one PC controller. Every other device connected must have its own unique ID equal or greater than 1:
in the network cannot exist two devices with the same ID.
An ID number is assigned automacally to each devices when they are turned on for the first me connected to a network.
In order to correctly assign a new available ID to each device for working properly in a Pronet network, follow these instrucons:
1. Switch offall the devices.
2. Connect them correctly to the network cables.
3. “TERMINATE” the latest device in the network connecon.
4. Switch on the first device keep pressed “PRESET” buon on the control panel.
5. Leaving the previous device switched on, repeat the previous operaon on the next device, unl the latest device is turned on.
The “Assign ID” procedure for a device makes the internal network controller to perform two opera
ons: reset the current ID; search the first free
ID in the network, starng from ID=1. If no other devices are connected (and powered on), the controller assume ID=1, that is the first free ID,
otherwise it searches the next one lefree.
These operaons ensure that every device has it’s own unique ID, if you need to add a new device to the network you simply repeat the operaon
of step 4. Every device maintains its ID also when it is turned-off, because the idenfier is stored in the internal memory and it is cleared only by
another “Assign ID” step, as explained above. This means that if your network is made always of the same devices the assigning ID procedure must
be executed only the first me the system is turned on.
For more detailed instrucƟon about PRONET see the PRONET USER’S MANUAL included with the soŌware.

Useful tools to set up properly a verƟcal array system using the SW215FA subwoofer
This is a list of tools that can be very useful to set properly a vercal array system with the SW215FA acve subwoofers.
CABLE TESTER
It is a good pracce to check all cables before each installaon, because even one faulty cable can compromise heavily the
system performance.
INCLINOMETER WITH LEVER
This tool can be used to verify the vercal array angle. It can be used at the top or at the boom of the array In this
case you have to sum all splay angles, so the maximum precision is needed for aiming the vercal array, parcularly
for long throw applicaons.
LASER DISTANCE METER
This instrument can be useful to measure the height of the vercal array and to know the distance between FOH-Subs and FOH-Array
for seng the delay me.
SMAART or similar acousƟc measurement system
These are useful to measure delays, phase and response of the system.
not pressed
pressed
last device
network
network
AX2065A
USB2CAN
PC NOTEBOOK
USB 2.0 port
AX2065A
AX2065P
AX2065A
AX2065P
SW215A
STATUS
CONVERTER
USB2CAN
CODE: S/N: RATINGS: RoHS COMPLIANT MADE IN ITALY
USB2CAN 00001 5V --- 200mA
EXAMPLE OF PRONET NETWORK WITH AX2065A AND SW215A

PRESET
The SW115FA has three factory presets already stored inside the
CORE DSP, these preset are ready to use the sub in combinaon with
AX2065A vercal array loudspeaker or any other professional audio
system:
STANDARD PRESET: the response starts at 45Hz and the cutoffis at
100Hz with LR 24dB/oct., use this preset for almost any applicaon
at ground stack and it must be used with the SW215FA set as flown
(see FLOWN SET UP).
INFRASUB PRESET: the response starts at 39Hz and the cutoffis
at 60Hz with LR 24dB/oct., use this preset when a very deep bass
response is required, it must be used at ground stack only, alone or
in combinaon with some other boxes set as STANDARD, absolutely
do not use it in combinaon of CARDIOD preset. NOTE: INFRA and
STANDARD PRESET must NOT be used together in close units.
CARDIOD PRESET: the response of this preset is the same of
STANDARD preset but when combined together as described further
the sub stack is capable to cancel tha bass in the backwards,
absolutely it must be used in combinaon of other two boxes and at
ground stack.
PREDICTION: EASE Focus 2
To aim correctly a complete system we suggests to use always the Aiming Soware - EASE Focus 2:
The EASE Focus 2 Aiming Soware is a 3D Acousc Modelling Soware that serves for the configuraon
and modelling of Line Arrays and convenonal speakers close to reality. It only considers the direct
field, created by the complex addion of the sound contribuons of the individual loudspeakers or
array components.
The design of EASE Focus is targeted at the end user. It allows the easy and quick predicon of the array
performance in a given venue. The scienfic base of EASE Focus stems from EASE, the professional
electro- and room acousc simulaon soware developed by AFMG Technologies GmbH. It is based on
the EASE GLL loudspeaker data file required for its use: AXIOM_AX Series_v2_1.GLL, please note that
the version must be 2.0 or more. The GLL file contains the data that defines the Line Array with regard to its possible configuraons as well as to
its geometrical and acouscal properes.
Download the EASE Focus 2 app from the AXIOM website at hƩp://www.axiomproaudio.com/ clicking on downloads secƟon of the product.
Use the menu opon Edit / Import System DefiniƟon File to import the file AXIOM_AX Series_v2_1.gll from the installaon Data folder, the
detailed instrucons to use the program are located in the menu opon Help / User’s Guide.
Note: Some windows system can require the .NET Framework 4 that can be download from microsowebsite at hp://www.microso.com/en-
us/download/default.aspx.
WARNING! CAREFULLY READ THE FOLLOWING INSTRUCTIONS AND CONDITION OF USE:
• This loudspeaker is designed exclusively for Professional audio applicaons. The product must be installed by qualified personal only.
• Proel strongly recommends that this loudspeaker cabinet be suspended taking into consideraon all current Naonal, Federal, State and
Local regulaons. Please contact the manufacturer for further informaon.
• Proel do not accept any liability for damage caused to third
pares due to improper installaon, lack of maintenance,
tampering or improper use of this product, including disregard
of acceptable and applicable safety standards.
• During assembly pay attention to the possible risk of
crushing. Wear suitable protective clothing. Observe all
instructions given on the rigging components and the
loudspeaker cabinets. When chain hoists are in operaon
ensure that there is nobody directly underneath or in the
vicinity of the load. Do not under any circumstances climb
on the array.
AIMING and SUSPENDING INSTRUCTIONS (FLOWN SET UP)
Suspending the sub-woofers has different advantages and some
inconvenient. One inconvenient is that it’s not possible to use the
cardioid configuraon, while another one is that as the sub-woofers
don’t couple with the ground and indoor usage can have different
behaviours depending on ceiling and walls. The advantages are that
the space underneath the stage can be free from subs, the coupling
between sub and sat is beer and, using a column of 4-6 sub boxes,
the basses can be steered more deeply into the audience with a more
uniform distribuon of the low frequencies.
The SW215FA subwoofers can be suspended alone or at the top of a
vercal array of AX2065A loudspeakers using the KPTSW215 fly bar.
The boxes are linked together in a column using a series of couplers
+15
+10
+5
0
-5
-10
-15
-20
-25
-30
-35 20 50 100 200 500 1K 2K 5K 10K 20K Hz
SW215A - PRESET RESPONSE
INFRA STANDARD
SUSPEND HOLES
SUSPEND HOLE
INDICATOR
REAR BOX
PIN ATTACHMENT
FRONT BOX
PIN ATTACHMENT
FRONT BOX
PIN ATTACHMENT
STRAIGHT SHACKLE 16mm
M10 FOOT FOR
STACKED INSTALLATION
(OPTIONAL)
IDENTIFICATION AND
DATA LABEL
KPTSW215 FLY BAR AND ACCESSORIES

integrated in the frame of each enclosure. Each system can be set properly both acouscally and mechanically, using the aiming soware.
Coupling the system in the front does not require any adjustment: using two locking pins, each loudspeaker box is fixed to the previous. The
sloed bar in the back is inserted in a U-shaped frame that features a series of numbered holes. Sliding the sloed bar in the U-shaped frame
of the next loudspeaker and inserng a locking pin in one of the numbered holes, it is possible to adjust the relave splay angle between two
adjacent loudspeakers in the array column.
KPTSW215 fly bar maximum capacity is 540 Kg (1190 lbs) with the 0° angle. It can support, with a safety factor of 10:1, up to:
• 8 AX2065A + 8 AX2065P (flybar from 0° to 10°)
• 12 AX2065A (flybar from 0 to 10°)
• 2 SW215FA + 4 AX2065A + 4 AX2065P (flybar at 0°)
• 2 SW215FA + 8 AX2065A (flybar at 0°)
• 6 SW215FA (flybar from 0° to 5°)
Follow the sequence in the figure
for fixing the fly bar at the first box.
Usually this is the first step before
liing up the system. Be careful to
insert properly all the locking pins
(1)(2) and (3)(4) then the shackle
(5) in the right holes as specified by
the aiming soware.
When lifting the system always
proceed gradually step by step,
paying aenon to secure the fly
bar to the box (and the box to the
other boxes) before pulling up the
system: this makes easier to insert
properly the locking pins. Also
when the system is released down,
unlock gradually the pins.
During the liing be very careful to
not let the cables enter the space
between one enclosure and the
other, as their compression could
cut them.
Please note that the Rear Link Bar
of the SW215FA cabinet has two
holes (see figure):
The hole signed as nr.1 must be
used for SW215FA-SW215FA sub-
sub link.
The hole signed as nr.2 must be
used for SW215FA-AX2065 sub-
sat link.
Wind loads
When planning an open-air event it is essenal to obtain current weather
and wind informaon. When loudspeaker arrays are flown in an open-air
environment, possible wind effects must be taken into account. Wind load
produces addional dynamic forces acng on the rigging components and
the suspension, which may lead to a dangerous situaon. If according to
the forecast wind forces higher than 5 b(29-38 Km/h) are possible, the
following acons have to be taken:
- The actual on-site wind speed has to be monitored permanently. Be
aware that wind speed typically increases with height above ground.
- Suspension and securing points of the array should be designed to
support double the static load in order to withstand any additional
dynamic forces.
WARNING!
Flying loudspeakers overhead at wind forces higher than 6 bŌ(39-49 Km/h) is not recommended.
If the wind force exceeds 7 b(50-61 Km/h) there is a risk of mechanical damage to the components which may lead to a dangerous situaon
for persons in the vicinity of the flown array.
- Stop the event and make sure that no person remains in the vicinity of the array.
- Lower and secure the array.
1
2
3
4
1
2
5
KPTSW215 FLY BAR ASSEMBLY SEQUENCE
1 = SW215FA-SW215FA hole
2 = SW215FA-AX2065 hole
none = rest hole
SW215FA REAR LINK BAR

1
32
1
2
KPTSW215 - SW215FA ARRAY ASSEMBLING SEQUENCE
MAX:
KPTSW215
+
6x SW215FA
4
for sub-sub linking use the
longer posiƟons
use the pin to set the
front linking bar:
rest, sat, or sub

1
1
2
32
4
KPTSW215 - SW215FA - AX2065A ASSEMBLING SEQUENCE
MAX:
KPTSW215
+
2x SW215FA
+
4x AX2065A
+
4x AX2065P
for sub-sat linking use the
shorter posiƟons
use the pin to set the
front linking bar:
rest, sat, or sub

CARDIOID SET UP
The cardioid preset must be used in a sub array of three SW215FA. Two box must be oriented towards the audience and one must be turned in
the opposite direcon (typically the box in the centre of the array). The boom and the top boxes must have the STANDARD PRESET, the box in
the middle must have the CARDIOID PRESET. The audio signal sent to all boxes is the same.
The CARDIOID PRESET has the same response of the STANDARD PRESET, but to obtain the maximum cancellaon on the back side of the array it
has the phase inverted and a proper level and delay seng.
The figure below shows two typical displacement of the array. The first with all the boxes in horizontal posion for a total height of 1713 mm and
a width of 800 mm. The second one with all the boxes in vercal posion for a total height of 800 mm and a width of 1713 mm.
NOTES:
When placing the cardioid array keep a distance to walls or other obstacles of at least 80 cm (2.6 ) in order not to affect the radiaon of the
reversed cabinet.
When placing mulple cardioid arrays keep a distance between them of at least 120 cm (3.9 ) in order not to maximize the combined radiaon
of whole arrays.
80 cm min.
2.7 Ōmin.
120 cm min.
3.9 Ōmin.
80 cm min.
2.7 Ōmin.
stage
wall or other
big ostacle
bass sum direcƟon
bass cancellaƟon direcƟon
audience floor

stage
wall or other
big ostacle
bass sum direcƟon
bass cancellaƟon direcƟon
audience floor
80 cm min.
2.7 Ōmin.
80 cm min.
2.7 Ōmin.
80 cm min.
2.7 Ōmin.
NOTES:
When placing the cardioid array keep a distance to walls or other obstacles of at least 80 cm (2.6 ) in order not to affect the radiaon of the
reversed cabinet.
When placing mulple cardioid arrays keep a distance between them of at least 80 cm (2.6 ) in order not to maximize the combined radiaon
of whole arrays.

LIMITED WARRANTY
Proel warrants all materials, workmanship and proper operaon of this product for a period of two years from the original date of purchase. If any defects are found
in the materials or workmanship or if the product fails to funcon properly during the applicable warranty period, the owner should inform about these defects the
dealer or the distributor, providing receipt or invoice of date of purchase and defect detailed descripon. This warranty does not extend to damage resulng from
improper installaon, misuse, neglect or abuse. Proel S.p.A. will verify damage on returned units, and when the unit has been properly used and warranty is sll
valid, then the unit will be replaced or repaired. Proel S.p.A. is not responsible for any “direct damage” or “indirect damage” caused by product defecveness.
• This unit package has been submied to ISTA 1A integrity tests. We suggest you control the unit condions immediately aer unpacking it.
• If any damage is found, immediately advise the dealer. Keep all unit packaging parts to allow inspecon.
• Proel is not responsible for any damage that occurs during shipment.
• Products are sold “delivered ex warehouse” and shipment is at charge and risk of the buyer.
• Possible damages to unit should be immediately nofied to forwarder. Each complaint for package tampered with should be done within eight days from product
receipt.
SAFETY INSTRUCTIONS
– To reduce the risk, close supervision is necessary when the product is used near children.
– Protect the apparatus from atmospheric agents and keep it away from water, rain and high humidity places.
– This product should be site away from heat sources such as radiators, lamps and any other device that generate heat.
– This product should be located so that its locaon or posion does not interfere with its proper venlaon and heang dissipaon.
– Care should be taken so that objects and liquids do not go inside the product.
– The product should be connected to a power supply mains line only of the type described on the operang instrucons or as marked on the product. Connect the
apparatus to a power supply using only power cord included making always sure it is in good condions.
– WARNING: The mains plug is used as disconnect device, the disconnect device shall remain readily operable.
– Do not cancel the safety feature assured by means of a polarized line plug (one blade wider than the other) or with a earth connecon.
– Make sure that power supply mains line has a proper earth connecon.
– Power supply cord should be unplugged from the outlet during strong thunderstorm or when leunused for a long period of me.
CE CONFORMITY
Proel products comply with direcve 2004/108/EC (EMC), as stated in EN 55103-1 and EN 55103-2 standards and with direcve 2006/95/CE (LVD), as stated in EN
60065 standard.
PROEL S.p.A. (World Headquarter) - Via alla Ruenia 37/43 - 64027 Sant’Omero (Te) - ITALY
Tel: [phone] Fax: [phone] www.axiomproaudio.com