Axiom SW2100AV2 User manual
SW2100AV2
USER MANUAL
2
Watch for these symbols:
IMPORTANT SAFETY INSTRUCTIONS
CAUTION
To prevent electric shock hazard,
do not connect to main power
supply while grille is removed.
3
LIMITED WARRANTY
CONDITIONS OF USE
FEDERAL COMMUNICATIONS COMMISSION (FCC) STATEMENT
DECLARATION OF CONFORMITY
The product is in compliance with:
EMC Direcve 2014/30/EU, LVD Direcve 2014/35/EU, RoHS Direcve 2011/65/EU and 2015/863/
EU, WEEE Direcve 2012/19/EU.
EN 55032 (CISPR 32) STATEMENT
The product is in compliance with:
S.I. 2016/1091 Electromagnec Compability Regulaons 2016, S.I. 2016/1101 Electrical Equipment
(Safety) Regulaons 2016, S.I. 2012/3032 The Restricon of the Use of Certain Hazardous Substances
in Electrical and Electronic Equipment Regulaons 2012.
CISPR 32 STATEMENT
4
INTRODUCTION
TECHNICAL SPECIFICATION
SYSTEM
TRANSDUCER
ELECTRICAL
ENCLOSURE & CONSTRUCTION
* Nominal consumpon is measured with pink noise with a crest factor of 12 dB, this can be considered a standard music program.
INDEX
4
4
5
5
5
6
6
6
6
PROT6
6
6
6
6
6
6
9
11
5
MECHANICAL DRAWING
OPTIONAL ACCESSORIES
NAC3FX-W-TOP-L DHSS10M20
NAC3MX-W-TOP-L
HTLACA KP210S
HTLACB
NE8MC-B-1 ESO2500LUxx
NL4FXX-W-L
COVERSW2100 AVCAT5PROxx
USB2CANDV2
see hp://www.axiomproaudio.com/ for detailed descripon and other available accessories.
*Note: See assembly instrucon downloadable from NEUTRIK WEB site at: hp://www.neutrik.com/
SPARE PARTS
NAC3PX-TOP 91DALITEMOD4HV
SCNAC-04 98SW2100WZ4
91AMDSW2100V2 94SPI10100
91DSPKT11 95MET300003
4 x M5
Flat Head
Allen
Screws
4 x M6
Pan Head
Allen
Screws
Adjustable feet (turn to adjust the height)
51 cm
20.1"
76 cm
29.9"
77 cm
30.3"
M20 Pole Adaptor
IMPORTANT
To install the AX12C bracket on the SW2100A
use the screws already present on the fixing plate,
as shown in the figure.
When removing the AX12C bracket from the SW2100A
put back the screws in the threaded holes
as shown in the figure, in order to avoid air leakage.
88 cm
34.7"
6
I/O AND CONTROL OPERATIONS
MAINS~ IN
MAINS~ OUT
WARNINGS:
• Connect no more than one subwoofer unit to the MAINS~ OUT connector.
• If you use the MAINS~ OUT turn on each subwoofer unit one a me.
• In the case of product failure or fuse replacement, disconnect the unit completely from the mains power.
• Use a suitable power cable and mains plug to build the power cable, it must only be connected to a socket
corresponding to the specicaons indicated on the amplier unit.
• See assembly instrucon downloadable from NEUTRIK WEB site at: hp://www.neutrik.com/
ON
PROT
SIGN LIMIT
INPUT
LINK
GND LIFT
NETWORK IN/OUT
TERMINATE
7
POWER OUT
PRESET BUTTON
ID ASSIGN
2 x AX12C
4 x AX12C
1 x AX12C
USER
WARNING: for the opmal protecon and equalizaon connect the exact number of AX12C modules specied by the
selected PRESET.
PRONET AX - OPERATION
Download the PRONET AX app registering on MY AXIOM at the website at hps://www.axiomproaudio.com/.
This can
be done by pressing the “TERMINATE” switch near the network connectors in the rear panel of the rst and the last device.
Assign the ID number
1.
2.
3.
4.
5.
With the network made always of the same devices the assigning ID procedure must be executed only the rst me the system
is turned on.
For more detailed instrucon about PRONET see the PRONET AX USER’S MANUAL included with the soware.
8
BASIC INSTALLATION INSTRUCTIONS
Pin locking and splay angles set up
USB2CAND
do not
pressed
pressed
LAST DEVICE
network
network
FIRST DEVICE
AND FOLLOWING
notebook
with PRONET AX so�ware
USB 2.0 port
1) pressed if the USB2CAND is the first device
2) not pressed if other AXIOM system is connected
to the other connector
EXAMPLE OF PRONET AX NETWORK WITH SW2100A
LOCKING PIN INSERTION
press and
insert
SW2100A-AX12C
and
AX12C-AX12C
locking pin
release
and lock
When connecng two speakers
together or one speaker to an
installaon accessory, insert
the pin in this hole first,
also use it to rest the pin when unused.
Use these holes for the splay angle:
0° as no splay.
2° as normal splay angle to obtain
a curved vercal array.
4° as splay angle to aim the first speaker
downward (stacked only).
AX12C SPLAY ANGLE SET UP
9
STACKED INSTALLATION OF AX12C USING SW2100AV2 SUBWOOFER AS BASE
WARNING! CAREFULLY READ THE FOLLOWING INSTRUCTIONS AND CONDITION OF USE:
SW2100AV2 is NOT designed to be suspended, use it in ground stack only.
1
2
3
4
5
6
WARNING: DO NOT STACK MORE
THAN TWO AX12C UNITS.
TWO AX12C STACKED ON A SW2100A
IMPORTANT:
WE SUGGEST TO ALWAYS
TIGHTEN THE THREADED KNOBS
ON BOTH SIDES OF THE BRACKETS
TO FASTEN TIGHTLY
THE COLUMNS TOGETHER
10
SW2100AV2 + 1 x AX12C CONNECTION EXAMPLE
SW2100AV2 + 2 x AX12C CONNECTION EXAMPLE
4 x 4mm² speaker cable
SW2100A + 1 x AX12C
ESO2500LU2 - lenght 2m
ESO2500LU5 - lenght 5m
ESO2500LU10 - lenght 10m
ESO2500LU15 - lenght 15m
ESO2500LU20 - lenght 20m
ESO2500LU25 - lenght 25m
4 x 4mm² speaker cable
SW2100A + 2 x AX12C
ESO2500LU05 - lenght 0,25m
ESO2500LU2 - lenght 2m
ESO2500LU5 - lenght 5m
ESO2500LU10 - lenght 10m
ESO2500LU15 - lenght 15m
ESO2500LU20 - lenght 20m
ESO2500LU25 - lenght 25m
11
SW2100AV2 + 2 x AX12C AIMING EXAMPLES
4° STACK
0°
4° STACK
2°
0°
2°
0°
0°
2°
2°
0°
2°
AIMING OPTIONS OF TWO AX12C MOUNTED ON A SW2100A
IMPORTANT:
NEVER INSTALL
2 OR MORE AX12C
AIMING THE SPEAKERS
TO EACH OTHER
WITH CLOSED ANGLES.
In other words, NEVER use
the 4° STACK posion
between two speakers.
PROEL S.p.A. (World Headquarters) - Via alla Ruenia 37/43 - 64027 Sant’Omero (Te) - ITALY
Tel: +39 0861 81241 Fax: +39 0861 887862 www.axiomproaudio.com
Table of contents
Other Axiom Subwoofer manuals
Axiom
Axiom SW1800A User manual
Axiom
Axiom SW36XFP User manual
Axiom
Axiom SW218XAV2 User manual
Axiom
Axiom SW210P User manual
Axiom
Axiom EP500 v4 User manual
Axiom
Axiom SW212Al User manual
Axiom
Axiom SW215P User manual
Axiom
Axiom SW2100P User manual
Axiom
Axiom EP175 v4 User manual
Axiom
Axiom SW18P User manual
