
USER MANUAL
SW218XP
passive subwoofer
KEY FEATURES
• Very High Output • Manifolded Transmission Line conguraon for very fast transient response
• Compact size for a very good output-to-weight rao • Tetracoil dual voice coil for e�tended linear response and increased power handling• Tetracoil dual voice coil for e�tended linear response and increased power handling
• High-strength, water repellent, glass ber reinforced cones
INTRODUCTION
The SW218XP subwoofer is designed to deliver high quality low frequency reproducon where very high output is a key requirement, together
with well dened deep bass response and fast transient response. Its compact size and light weight
make it suitable for several dierent uses, ranging from touring applicaons to �ed installaons and
high-level dance clubs.
The SW218XP is a very high quality powered subwoofer system featuring some of the most advanced
technologies for low frequency reproducon. Its unique and innovave design is based on a conguraon
that can be dened as Manifolded Transmission Line.
It uses manifolding of the front side of the cones to ma�imize the mutual coupling between the
two drivers, while loading the back of the cone with a large-size transmission line that has the
funcon to create a transmission path from the back of the transducers to the front. This innovave
conguraon does not use any large resonant cavity to load the speaker in order to get the lower
octave and this reduces signicantly pressure decay me inside the enclosure, with large advantages
in terms of denion both at the lowest end and the upper bass. At the same me, it doesn’t use very
long transmission line paths as well. Its working principle is an hybrid combinaon between a short
transmission line and an overdamped ree� load. Moreover, the ma�imizaon of the mutual coupling between the drivers increase the fastness
of the transient response while ma�imizing the overall energy eciency as well.
The SW218P subwoofer system is equipped with two high power 18” (460mm) transducers capable of long e�cursion (up to 30mm peak-to-
peak), and featuring a a large displacement suspension system. These transducers use Tetracoil technology, where two dierent, a�ially separated
magnec gaps and two inside-outside 100mm (4” ) diameter voice coils are wound on the same former and suspended evenly in the two magnec
gaps. This creates an equivalent voice coil diameter greater than 6”, resulng in a larger heat dissipaon area for and increased power handling.
Addional key advantages of the Tetracoil technology are also minimized distoron and a very symmetric and at inductance curve.
Cones are made of very high-sness berglass reinforced paper, featuring also invisible water repellent treatment.
TECHNICAL SPECIFICATION
Acouscal Connectors
System type Manifolded Transmission Line Connector Type Neutrik® Speakon® NL4 � 2
Transducer
Two 18” (460 mm), 4” (100 mm) VC,
Water repellent cone and epo�y coated
plates, 100mm (4in) Tetracoil dual voice coil,
equivalent to a single coil diameter
larger than 152mm (>6in) suspension, ultra
linear suspension behavior
Input Wiring LF1 = Pin 1+/1-; LF2 = Pin 2+/2-
Mechanical
Width 1215 mm (47.87”)
Height 590 mm (23.24”)
Depth 950 mm (37.43”)
Frequency response (±3 dB) 30 Hz – 92 Hz (Processed) Depth with Wheels / Dolly 1078 mm (42.44”) / 1110 mm (43.70”)
Frequency response (±10 dB) 27 Hz – 300 Hz (Unprocessed) Construcon 15 mm, reinforced Phenolic Birch
Sensivity (1.41V @ 1m, 2Pi) 101 dB (averaged from 40 to 100 Hz) Paint High resistance, water based paint
Ma�imum Peak SPL @ 1m 143 dB Transport 10 handles
Electrical Net Weight 114 Kg (251.3 lbs.)
Nominal Impedance 8 Ω + 8 Ω Wheels or Transport Dolly 4 heavy-load 100 mm ø (oonal)
Minimum Impedance 5.7 Ω + 5.7 Ω @ 36 Hz
Power Handling Connuous* 1800 W + 1800 W
Power Handling Program 3600 W + 3600 W
Power Handling Peak 7000 W + 7000 W
Power Compression
@ -10 dB Power (180 W + 180 W) = 0.6 dB
@ -3 dB Power (900 W + 900 W) = 2.0 dB
@ 0 dB Power (1800 W + 1800 W) = 3.4 dB
* AES Pink Noise Power
revision 2017-03-29