AXIOMTEK eBOX532-100-FL Series User manual

eBOX532-100-FL Series
Fanless Embedded System
User’s Manual

ii
Disclaimers
This manual has been carefully checked and believed to contain accurate information.
Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or any third
party’s rights, and any liability arising from such use.
Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy,
completeness or usefulness of any information in this document. Axiomtek does not make
any commitment to update the information in this manual.
Axiomtek reserves the right to change or revise this document and/or product at any time
without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted, in
any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,
without the prior written permission of Axiomtek Co., Ltd.
Copyright 2016 Axiomtek Co., Ltd.
All Rights Reserved
Jan. 2016, Version A2
Printed in Taiwan

iii
Safety Precautions
Before getting started, please read the following important safety precautions.
1. The eBOX532-100-FL does not come equipped with an operating system. An
operating system must be loaded first before installing any software into the
computer.
2. Be sure to ground yourself to prevent static charge when installing the internal
components. Use a grounding wrist strap and place all electronic components in any
static-shielded devices. Most electronic components are sensitive to static electrical
charge.
3. Disconnect the power cord from the eBOX532-100-FL before making any installation.
Be sure both the system and the external devices are turned OFF. Sudden surge of
power could ruin sensitive components. Make sure the eBOX532-100-FL is properly
grounded.
4. Make sure the voltage of the power source is correct before connecting the
equipment to the power outlet.
5. Turn OFF the system power before cleaning. Clean the system using a cloth only.
Do not spray any liquid cleaner directly onto the screen.
6. Do not leave this equipment in an uncontrolled environment where the storage
temperature is below -20℃or above 60℃. It may damage the equipment.
7. Do not open the system’s back cover. If opening the cover for maintenance is a must,
only a trained technician is allowed to do so. Integrated circuits on computer boards
are sensitive to static electricity. To avoid damaging chips from electrostatic
discharge, observe the following precautions:
Before handling a board or integrated circuit, touch an unpainted portion of the
system unit chassis for a few seconds. This will help to discharge any static
electricity on your body.
When handling boards and components, wear a wrist-grounding strap, available
from most electronic component stores.

iv
Classification
1. Degree of production against electric shock: not classified
2. Degree of protection against the ingress of water: IP40
3. Equipment not suitable for use in the presence of a flammable anesthetic mixture
with air or with oxygen or nitrous oxide.
4. Mode of operation: Continuous
5. Type of protection against electric shock: Class I equipment
General Cleaning Tips
You may need the following precautions before you begin to clean the computer. When you
clean any single part or component for the computer, please read and understand the details
below fully.
When you need to clean the device, please rub it with a piece of dry cloth.
1. Be cautious of the tiny removable components when you use a vacuum cleaner to
absorb the dirt on the floor.
2. Turn the system off before you start to clean up the component or computer.
3. Never drop the components inside the computer or get circuit board damp or wet.
4. Be cautious of all kinds of cleaning solvents or chemicals when you use it for the sake of
cleaning. Some individuals may be allergic to the ingredients.
5. Try not to put any food, drink or cigarette around the computer.

v
Cleaning Tools:
Although many companies have created products to help improve the process of cleaning
your computer and peripherals users can also use household items to clean their computers
and peripherals. Below is a listing of items you may need or want to use while cleaning your
computer or computer peripherals.
Keep in mind that some components in your computer may only be able to be cleaned using
a product designed for cleaning that component, if this is the case it will be mentioned in the
cleaning.
Cloth: A piece of cloth is the best tool to use when rubbing up a component. Although
paper towels or tissues can be used on most hardware as well, we still recommend
you to rub it with a piece of cloth.
Water or rubbing alcohol: You may moisten a piece of cloth a bit with some water or
rubbing alcohol and rub it on the computer. Unknown solvents may be harmful to the
plastics parts.
Vacuum cleaner: Absorb the dust, dirt, hair, cigarette particles, and other particles
out of a computer can be one of the best methods of cleaning a computer. Over time
these items can restrict the airflow in a computer and cause circuitry to corrode.
Cotton swabs: Cotton swaps moistened with rubbing alcohol or water are excellent
tools for wiping hard to reach areas in your keyboard, mouse, and other locations.
Foam swabs: Whenever possible it is better to use lint free swabs such as foam
swabs.
Note We strongly recommended that you should shut down the system before you start
to clean any single components.
Please follow the steps below:
1. Close all application programs
2. Close operating software
3. Turn off power switch
4. Remove all device
5. Pull out power cable

vi
Scrap Computer Recycling
If the computer equipments need the maintenance or are beyond repair, we strongly
recommended that you should inform your Axiomtek distributor as soon as possible for the
suitable solution. For the computers that are no longer useful or no longer working well,
please contact your Axiomtek distributor for recycling and we will make the proper
arrangement.
Trademarks Acknowledgments
Axiomtek is a trademark of Axiomtek Co., Ltd. IBM, PC/AT, PS/2, VGA are trademarks of
International Business Machines Corporation.
Intel®and Pentium®are registered trademarks of Intel Corporation.
MS-DOS, Microsoft C and QuickBASIC are trademarks of Microsoft Corporation.
VIA is a trademark of VIA Technologies, Inc.
SST is a trademark of Silicon Storage Technology, Inc.
UMC is a trademark of United Microelectronics Corporation.Other brand names and
trademarks are the properties and registered brands of their respective owners.

vii
Table of Contents
Disclaimers.............................................................................................................. ii
Safety Precautions................................................................................................. iii
Classification.......................................................................................................... iv
General Cleaning Tips ........................................................................................... iv
Scrap Computer Recycling.................................................................................... vi
CHAPTER 1 INTRODUCTION........................................................................1
1.1 General Description............................................................................ 1
1.2 System Specifications........................................................................ 3
1.2.1 CPU .................................................................................................................... 3
1.2.2 I/O System ......................................................................................................... 3
1.2.3 System Specification........................................................................................ 4
1.3 Dimensions ......................................................................................... 5
1.4 I/O Outlets............................................................................................ 7
1.5 Packing List....................................................................................... 10
CHAPTER 2 HARDWARE INSTALLATION.................................................11
2.1 Installing the Memory Module.......................................................... 11
2.2 Installing the Hard Disk Drive .......................................................... 14
2.3 Installing the CompactFlashTM Card................................................ 16
2.4 Installing DIN Mount (optional) ........................................................ 19
2.5 Installing Rail Mount......................................................................... 21
CHAPTER 3 AMI BIOS Setup Utility ...........................................................23
3.1 Starting.............................................................................................. 23
3.2 Navigation Keys................................................................................ 24
3.3 Main Menu ......................................................................................... 25
3.4 Advanced Menu ................................................................................ 26
3.5 Chipset Menu .................................................................................... 33
3.6 Boot Menu ......................................................................................... 40
3.7 Security Menu ................................................................................... 41
3.8 Save & Exit Menu.............................................................................. 42
APPENDIX A Watchdog Timer....................................................................45
About Watchdog Timer .................................................................................... 45
How to Use Watchdog Timer ........................................................................... 45
Sample Program............................................................................................... 47

viii
This page is intentionally left blank.

eBOX532-100-FL Series User’s Manual
Introduction
1
CHAPTER 1
INTRODUCTION
This chapter contains general information and detailed specifications of the eBOX532-100-FL.
The Chapter 1 includes the following sections:
General Description
System Specification
Dimensions
I/O Outlets
Package List
1.1 General Description
The eBOX532-100-FL is an embedded system that supports onboard AMD G-Series single
core T40R (1.0 GHz) and Fusion Controller Hub A50M that delivers outstanding system
performance through high-bandwidth interfaces, multiple I/O functions for interactive
applications and various embedded computing solutions, and provide Windows®XPE,
Windows®7, Windows®XP and Linux, suitable for the most endurable operation. It features
fanless design with full feature I/O, has one 204-pin unbuffered SO-DIMM socket for DDR3
1066MHz SO-DIMM memory, maximum memory capacity up to 4GB. It also features one
Gigabit/Fast Ethernet, four USB 2.0 high speed compliant, and built-in high definition audio
codec that can achieve the best stability and reliability for industrial applications. Additionally,
it provides you with unique embedded features, such as two serial ports (2x RS-232) and
enhanced system dependability by built-in Watchdog Timer.
Features
1. Support AMD G-Series APU T40R (1.0GHz)
2. AMD Fusion Controller Hub A50M chipset
3. 1 DDR3 SO-DIMM supports up to 4GB memory capacity
4. 4 USB 2.0 ports
5. 2 COM ports
6. Supports one 10/100/1000Mbps Ethernet port
7. Supports one 2.5”SATA-600 HDD drive bay, one CompactFlash™
8. Watchdog timer
9. Din-rail/desktop/wall mount
Reliable and Stable Design
The eBOX532-100-FL adopts the advanced cooling system and supporting the
CompactFlash™, which makes it especially suitable for vibration environments, best for
industrial automation, digital signage and gaming application.

eBOX532-100-FL Series User’s Manual
Introduction
2
O.S. Supported
The eBOX532-100-FL supports Windows®XP, Windows 7 and also supports embedded OS,
such as Windows®XP embedded and Linux. For storage device, the eBOX532-100-FL
supports one 2.5" SATA-600 HDD drive bay, and one type II CompactFlash™slot.
ATX or AT Mode Selection Jumper (JP6)
If JP6 is enabled for power input, the system will be automatically power on without pressing
soft power button. If JP6 is disabled for power input, it is necessary to manually press soft
power button to power on the system.
NOTE This function is similar to the feature of power on after power failure,
which is controlled by hardware circuitry instead of BIOS.
NOTE Once the Jumper is changed to AT model, the system power switch is no
longer usable and system will power-on once DC power enter system.
Therefore, customer needs to have external power switch to switch on/off
the system (because eBOX532’s power switch is no longer workabl e at AT
mode).
Function
Setting
Disable auto power on (ATX Mode)
1-2 close
Enable auto power on (AT Mode)
1-2 open

eBOX532-100-FL Series User’s Manual
Introduction
3
1.2 System Specifications
1.2.1 CPU
CPU
Onboard AMD G-Series APU single core T40R 1.0 GHz.
System Chipset
AMD Fusion Controller Hub A50M.
BIOS
American Megatrends Inc. UEFI (Unified Extensible Firmware Interface)
BIOS
System Memory
One 204-pin unbuffered DDR3 SO-DIMM socket.
Maximum up to 4GB DDR3 1066MHz memory.
1.2.2 I/O System
System I/O Outlet
Two 9-pin D-Sub male connectors, COM1/2 for RS-232
One 15-pin D-Sub female connector for VGA (for eBOX532-100-VGA-FL) or
for DisplayPort (for eBOX532-100-PGA-FL)
One Audio connector (Line-IN, Line-OUT)
One PS/2 connector for Keyboard and M/S through Y-Type cable
One RJ-45 connector for 10/100/1000Base-T Ethernet
Four USB 2.0 connectors
One 5V DC-IN Power Input connector
NOTE DP (DisplayPort) Module
It is used for eBOX532-100-FL1.0G-PGA.
3 types of module are offered by option
- DisplayPort to HDMI Female Cable DP to HDMI
- DisplayPort to DVI Female Cable DP to DVI
- DisplayPort to VGA Female Cable DP to VGA

eBOX532-100-FL Series User’s Manual
Introduction
4
1.2.3 System Specification
Watchdog Timer
1~255 seconds; up to 255 levels.
Power Supply
External AC 25W AC/DC power adapter with lock
(Output: DC 5V @ 5A)
Operation Temperature
0~45 ℃(WT HDD)
0~50 ℃(WT CF/SSD)
Storage Temperature
-20℃~ 80℃(-4 ºF ~ 176ºF)
Humidity
10% ~ 90% (non-condensation)
Vibration Endurance
1Grms w/ HDD (5 ~ 500Hz, X, Y, Z directions)
Weight
0.5 kg (1.1 lb)
Dimensions
130mm(5.11”) (W) x 95.4mm(3.75”) (D) x 47.1mm(1.85”) (H)
NOTE All specifications and images are subject to change without notice.

eBOX532-100-FL Series User’s Manual
Introduction
5
1.3 Dimensions
The following diagrams show you dimensions and outlines of the eBOX532-100-VGA-FL.

eBOX532-100-FL Series User’s Manual
Introduction
6
eBOX532-100-PGA-FL.

eBOX532-100-FL Series User’s Manual
Introduction
7
1.4 I/O Outlets
The following figures show you I/O outlets on front view of the eBOX532-100-VGA-FL &
eBOX532-100-PGA-FL
Front View
Rear View (eBOX532-100-VGA-FL)

eBOX532-100-FL Series User’s Manual
Introduction
8
Rear View (eBOX532-100-PGA-FL)
NOTE P D (DisplayPort) Module
It is used for eBOX532-100-FL1.0G-PGA.
3 types of module are offered by option
- DisplayPort to HDMI Female Cable DP to HDMI
- DisplayPort to DVI Female Cable DP to DVI
- DisplayPort to VGA Female Cable DP to VGA

eBOX532-100-FL Series User’s Manual
Introduction
9
SATA Connector(SATA 1)
SATA connector is for high-speed SATA interface ports and each SATA
connector supports a single SATA device.
Plug one end of the SATA cable to the SATA connector, and the other end of
cable to the SATA hard drive.
Pin
Signal
1
GND
2
SATA_TX+
3
SATA_TX-
4
GND
5
SATA_RX-
6
SATA_RX+
7
GND

eBOX532-100-FL Series User’s Manual
Introduction
10
1.5 Packing List
The package bundled with your eBOX532-100-FL should contain the following items:
eBOX532-100-FL System Unit x 1
eBOX532-100-FL Quick Manual x 1
Power Cord x 1
CD x 1 (For Driver and User’s Manual)
Wallmount Brackets
Keyboard/Mouse Y-cable
Screws
25W 5V AC/DC Power Adapter
HDD Mylar x1
(Figure –Power Adapter Pin Assignment)
If you can not find this package or any items are missing, please contact Axiomtek distributors
immediately.
NOTE P D (DisplayPort) Module
It is used for eBOX532-100-FL1.0G-PGA.
3 types of module are offered by option
- DisplayPort to HDMI Female Cable DP to HDMI
- DisplayPort to DVI Female Cable DP to DVI
- DisplayPort to VGA Female Cable DP to VGA

eBOX532-100-FL Series User’s Manual
Hardware Installation
11
CHAPTER 2
HARDWARE INSTALLATION
The eBOX532-100-FL is convenient for your various hardware configurations, such as
Memory Module, HDD (Hard Disk Drive), and CompactFlashTM card. The chapter 2 will show
you how to install the hardware. It includes:
2.1 Installing the Memory Module
Step 1 Turn off the system, and unplug the AC/DC power cord.
Step 2 Turn the system upside down to locate screws at the bottom.
Step 3 Loosen these screws, and remove the back cover from the system.

eBOX532-100-FL Series User’s Manual
Hardware Installation
12
Step 4 Locate the memory module as marked.
Step 5 Hold one side of the module, and insert the gold colored contact into the socket.
Push the module down.
Step 6 The memory module is locked by two latches on the sides.