AXIOMTEK SHB160 Series User manual

SHB160 Series
Intel®Socket 1700 CoreTM i7/ i5/ i3
Processors PICMG®v1.3 Full-size
CPU Card
User’s Manual

ii
Disclaimers
This manual has been carefully checked and is believed to contain accurate information.
Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or any third
party’s rights, and any liability arising from such use.
Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy,
completeness or usefulness of any information in this document. Axiomtek does not make any
commitment to update the information in this manual.
Axiomtek reserves the right to change or revise this document and/or product at any time
without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted, in any
form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without
the prior written permission of Axiomtek Co., Ltd.
CAUTION
Wrong type of batteries may cause explosion. It is recommended that users only replace with
the same or equivalent type of batteries as suggested by the manufacturer once properly
disposing of any used ones.
©Copyright 2023 Axiomtek Co., Ltd.
All Rights Reserved
June 2023, Version A1
Printed in Taiwan

iii
ESD Precautions
Computer boards have integrated circuits sensitive to static electricity. To prevent chipsets from
electrostatic discharge damage, please take care of the following jobs with precautions:
◼Do not remove boards or integrated circuits from their anti-static packaging until you are
ready to install them.
◼Before holding the board or integrated circuit, touch an unpainted portion of the system
unit chassis for a few seconds. Doing so can discharge static electricity from your body.
◼Wear a grounding wrist strap, available from most electronic component stores, when
handling boards and components.
Trademarks Acknowledgments
Axiomtek is a trademark of Axiomtek Co., Ltd.
Intel®CoreTM i7/ i5/ i3 are trademarks of Intel Corporation.
Windows®is a trademark of Microsoft Corporation.
AMI is a trademark of American Megatrend Inc.
IBM, PC/AT and PS/2 are trademarks of International Business Machines Corporation.
Other brand names and trademarks are the properties and registered brands of their respective
owners.

iv
Table of Contents
Disclaimers.....................................................................................................ii
ESD Precautions ...........................................................................................iii
Section 1 Introduction.........................................................1
1.1 Features ...............................................................................................1
1.2 Specifications ......................................................................................2
1.3 Packing list ..........................................................................................3
Section 2 Board and Pin Assignments ..............................5
2.1 Board Layout .......................................................................................5
2.2 Block Diagram .....................................................................................6
2.3 Jumper Settings ..................................................................................7
2.3.1 Auto Power On (JP1) ................................................................................ 8
2.3.2 Restore BIOS Optimal Defaults (JP2)...................................................... 8
2.4 Connectors ..........................................................................................9
2.4.1 Temperature Sensor Connector (CN15 AND CN16) (Optional)........... 10
2.4.2 Ethernet Ports (CN22) ............................................................................. 10
2.4.3 Front Panel Connector (CN26)................................................................11
2.4.4 DVI-I Connector (CN31) .......................................................................... 12
2.4.5 Internal USB 2.0 Connectors (CN33) ..................................................... 13
2.4.6 Rear I/O USB 3.2 (Gen2x1, 10Gbps) Connectors (CN35 and CN36)... 13
2.4.7 Internal PS/2 Keyboard and Mouse Connectors (CN28 and CN29) ... 13
2.4.8 COM Connectors (COM1~COM4) .......................................................... 14
2.4.9 FAN Connectors (CPU FAN, FAN2 and FAN3) ...................................... 14
2.4.10 SATA 3.0 Connectors (CN10~CN12/CN17~19)...................................... 15
2.4.11 Intel® HD Audio Digital Header (CN5) .................................................... 15
2.4.12 ATX Power Connector (CN13) ................................................................ 15
2.4.13 TPM Pin Header (CN7) ............................................................................ 16
2.4.14 Parallel Port Connector (CN2)................................................................ 17
2.4.15 M.2 2280 Key M NVMe SSD (CN34)........................................................ 18
2.4.16 Internal USB 3.2 Gen1x1 (5 Gbps) Connector (CN24 AND CN25) ...... 19
2.4.17 Display Port 1.4 Connector (CN30)........................................................ 20
Section 3 Hardware Installation........................................21
3.1 Installing the Processor....................................................................21
3.2 Installing the Memory........................................................................26
Section 4 Hardware Description.......................................27
4.1 Microprocessors ...............................................................................27

v
4.2 BIOS ...................................................................................................27
4.3 System Memory.................................................................................27
Section 5 AMI BIOS Setup Utility......................................29
5.1 Starting...............................................................................................29
5.2 Navigation Keys ................................................................................29
5.3 Main Menu..........................................................................................31
5.4 Advanced Menu.................................................................................32
5.5 Chipset Menu.....................................................................................45
5.6 Security Menu....................................................................................52
5.7 Boot Menu..........................................................................................53
5.8 Save & Exit Menu ..............................................................................54
Appendix A Watchdog Timer...............................................57
A.1 About Watchdog Timer .....................................................................57
A.2 How to Use Watchdog Sample Program .........................................57
Appendix B VMD(RAID) Configuration................................61
Appendix C PCI IRQ Routing...............................................65
C.1 PICMG® PCI IRQ Routing ..................................................................65
Appendix D iAMT Settings...................................................67
Entering Management Engine BIOS Extension (MEBx)............................67
Set and Change Password..........................................................................67
iAMT Settings ...............................................................................................68
iAMT Web Console ......................................................................................71
Appendix E PICMG®v1.3 Interface Definition .....................73
Appendix F TPM Module Installation..................................79

vi
This page is intentionally left blank.

SHB160 LGA1700 Full-size CPU Card
Introduction 1
Section 1
Introduction
The SHB160 PICMG®v1.3 full-size Single Board Computer supports an LGA1700 socket for
Intel®Core i7/ i5/ i3 desktop processors. The transfer rate reaches 4400 MHz. The board
integrates an Intel®R680E/H610E chipset that delivers outstanding system performance
through high-bandwidth interfaces, multiple I/O functions for interactive applications and various
embedded computing solutions. There are four 288-pin DDR5 DIMM sockets for dual channel
DDR5 4800 MHz with maximum memory capacity up to 128GB support ECC(R680E) /Non
ECC memory. The board also features dual 2.5 Gigabit Ethernet, SATA6Gbps with SATARAID
0/1/5/10(R680E ) by PCH, USB 2.0, and USB 3.2 (Gen1x1/Gen2x1) high speed compliant ports
and built-in Intel®HD Audio Digital Header to achieve the best stability and reliability for
industrial applications.
1.1 Features
⚫LGA1700 socket 12th/13th Generation Intel®Core processors up to 125W
⚫Intel®R680E/H610E PCH
⚫4 DDR5 unbuffered DIMM max. up to 128GB memory capacity
⚫Intel®iAMT (R680E/H610 PCH) and TPM2.0 module supported (optional)
⚫PCIe Gen. 4 at 16GT/s supported
⚫USB 3.2 (Gen2x1 , 10Gbps) supported

SHB160 LGA1700 Full-size CPU Card
2 Introduction
1.2 Specifications
⚫CPU
◼LGA1700 socket 12th/13th Generation Intel® Core™i7/i5/i3, Pentium® and
Celeron® processors (Raptor Lake) up to 125W
⚫System Chipset
◼Intel®R680E
◼Intel®H610E
⚫CPU Socket
◼LGA1700 socket
⚫DRAM Transfer Rate
◼4400 MHz
⚫BIOS
◼AMI BIOS via SPI interface with socket
⚫System Memory
◼Four 288-pin DDR5 4400MHz DIMM sockets
◼Maximum up to 128GB DDR5 memory
◼Supports the memory with ECC function (R680E Only)
⚫L1, L2, L3 Cache: Integrated in CPU
⚫Onboard Multi I/O
◼Serial ports: two RS-232/422/485 port in 2x5-pin (pitch=2.54mm) box-header (COM
1/2) and two RS-232 ports in 2x5-pin (pitch=2.54mm) box-header (COM 3/4)
◼Parallel Port: one 26-pin 2.54-pitch box-header; SPP/EPP/ECP supported
⚫USB Interface
R680E
◼Four USB3.2 (Gen1x1) ports on internal box header
◼Two USB3.2 (Gen2x1) ports on rear I/O
◼Two USB2.0 ports on internal pin header
◼One USB2.0 ports with 180D internal type A
◼Four USB2.0 ports via SHB connector-C via golden fingers
H610E
◼Two USB3.2 (Gen1x1) ports on internal box header
◼Two USB3.2 (Gen2x1) ports on rear I/O
◼Two USB2.0 ports on internal pin header
◼Four USB2.0 ports via SHB connector-C via golden fingers
⚫Onboard Graphics
◼Integrated Intel®UHD graphics supporting DVI-I
◼Integrated Intel®UHD graphics supporting DisplayPort (internal header)
◼DVI/VGA: Max. resolution is 1920x1200 at 60 Hz.
◼Internal DP1.4 Connector: Max resolution is 4096 x 2160 at 60Hz. Must use with
Axiomtek DP kit.

SHB160 LGA1700 Full-size CPU Card
Introduction 3
⚫Ethernet
◼LAN1/LAN2: Intel®i225LM with iAMT / Intel®i225V Ethernet controller
◼Support 2500/1000/100/10Mbps Gigabit/Fast Ethernet
⚫Storage
◼Serial ATA:
Six SATA 3.0 ports (6Gbps performance) with SATA RAID 0/1/5/10 (R680E)
Four SATA 3.0 ports (6Gbps performance) (H610E)
◼One M.2 2280 Key M (R680E Only)
⚫Audio
◼Supports HD audio interface as a 2x8 pin header
◼Supports audio kit AX93242 with MIC-in/Line-in/speaker-out (option kit)
⚫Watchdog Timer
◼1~255 seconds or minutes; up to 255 levels
⚫Hardware Monitor
◼Monitoring temperatures, voltages and cooling fan status
⚫Dimensions
◼338mm x 126mm
⚫Expansion Interface
◼One PCI-Express x16 (Gen.4)
◼One PCI-Express x4 (or four PCI-Express x1) (Gen.4)
◼Four PCI
Note
All specifications and images are subject to change without notice.
1.3 Packing list
⚫1 x slot CPU card
⚫1 x Driver DVD
⚫1 x SATA cable
⚫1 x COM cable
**SHB160 series required specially designed cooler "711000001X00", please order as set**

SHB160 LGA1700 Full-size CPU Card
4 Introduction
This page is intentionally left blank.

SHB160 LGA1700 Full-size CPU Card
Board and Pin Assignments 5
Section 2
Board and Pin Assignments
2.1 Board Layout
Top View

SHB160 LGA1700 Full-size CPU Card
6 Board and Pin Assignments
2.2 Block Diagram
R680E

SHB160 LGA1700 Full-size CPU Card
Board and Pin Assignments 7
2.3 Jumper Settings
Ajumper is a small component consisting of a jumper clip and jumper pins. Install a jumper clip
on two jumper pins to close a jumper. Remove the jumper clip from two jumper pins to open a
jumper. The following illustration shows how to set up a jumper.
Before applying power to the SHB160 series, please make sure all of the jumpers are in factory
default position. Below you can find a summary table and onboard default settings.
Note
Turn off power before changing any default jumper settings.
Jumper
Description
Setting
JP1
Auto Power On
Default: Enable
1-2 Close
JP2
Restore BIOS Optimal Defaults
Default: Normal Operation
1-2 Close

SHB160 LGA1700 Full-size CPU Card
8 Board and Pin Assignments
2.3.1 Auto Power On (JP1)
If JP3 is enabled for power input, the system will be automatically powered on without
pressing soft power button. If JP1 is disabled for power input, it is necessary to manually
press soft power button to power on the system.
2.3.2 Restore BIOS Optimal Defaults (JP2)
Put jumper clip to pin 2-3 for a few seconds then move it back to pin 1-2. Doing this
procedure can restore BIOS optimal defaults.
Function
Setting
Enable auto power on (Default)
1-2 close
Disable auto power on
2-3 close
Function
Setting
Normal operation (Default)
1-2 close
Restore BIOS optimal defaults
2-3 close

SHB160 LGA1700 Full-size CPU Card
Board and Pin Assignments 9
2.4 Connectors
Signals go to other parts of the system through connectors. Loose or improper connection might
cause problems. Make sure all connectors are properly and firmly connected. Here is a
summary table showing all connectors on the board.
Jumpers/Headers/Connectors
1
ATX Power Connector (CN13)
18
M.2 /E Key (2230)(CN27)
2
DDR5 Socket (DIMM0.DIMM1)
19
Restore BIOS Optimal Defaults (JP2)
3
TPM Pin Header (CN7)
20
DEBUG PORT Connector(CN21)
4
FAN Connector (FAN2)
21
Internal USB 2.0 Connector(CN23)
5
FAN Connector (FAN3)
22
Internal USB 3.2 Gen1x1 Connector (CN25)
6
Parallel Port Connector (CN2)
23
Internal USB 3.2 Gen1x1 Connector(CN24)
7
COM Connector (COM1)
24
Front Panel Connector (CN26)
8
COM Connector (COM2)
25
FAN Connectors (CPU Fan)
9
COM Connector (COM3)
26
M.2 2280 Key M NVMe SSD (CN34)
10
COM Connector (COM4)
27
Internal USB 2.0 Connector(CN33)
11
HD Audio Digital Header For
AX93242(CN5)
28
Internal PS/2 Mouse Connector (CN28)
12
Temperature Sensor Connector (CN15)
29
Internal PS/2 Keyboard Connector (CN29)
13
Temperature Sensor Connector (CN16)
30
PICMG_1.3 Gold Finger
14
SATA 3.0 Connector
(CN10~CN12/CN17~19)
31
PICMG_1.3 Gold Finger
15
Auto Power On (JP1)
32
PICMG_1.3 Gold Finger
16
12th Intel® Alder Lake LGA 1700 socket
33
PICMG_1.3 Gold Finger
17
Display Port 1.4 Connector (CN30)
34
RTC Battery Socket (BAT1)
Rear I/O Jumpers/Headers/Connectors
35
Ethernet Ports (CN22)
37
DVI-I Connector (CN31)
36
Ethernet Ports (CN22)
38
Rear I/O l USB 3.2 Gen2x1 Connector (CN35
and CN36)

SHB160 LGA1700 Full-size CPU Card
10 Board and Pin Assignments
2.4.1 Temperature Sensor Connector (CN15 AND CN16)
(Optional)
This is a 2-pin connector for temperature sensor (NTC thermistor) interface. The
thermistor value should be 10K and its B value is 3435K.
2.4.2 Ethernet Ports (CN22)
The board has two RJ-45 connectors: LAN1 (i226V) and LAN2 (i226LM). Ethernet
connection can be established by plugging one end of the Ethernet cable into this RJ-45
connector and the other end (phone jack) to a 2500/1000/100/ Base-T hub.
LAN1 LAN2
Pin
Signal
1
Sensor Input
2
GND
Pin
1000
Base-T
100/10
Base-T
Description
L1
BI_DA+
TX+
Bidirectional or Transmit Data+
L2
BI_DA-
TX-
Bidirectional or Transmit Data-
L3
BI_DB+
RX+
Bidirectional or Receive Data+
L4
BI_DC+
N.C.
Bidirectional or Not Connected
L5
BI_DC-
N.C.
Bidirectional or Not Connected
L6
BI_DB-
RX-
Bidirectional or Receive Data-
L7
BI_DD+
N.C.
Bidirectional or Not Connected
L8
BI_DD-
N.C.
Bidirectional or Not Connected
A
Speed LED
2500: Green
1000: Orange
100/10: OFF
B
Active Link LED (Yellow)
Off: No link
Blinking: Data activity detected

SHB160 LGA1700 Full-size CPU Card
Board and Pin Assignments 11
2.4.3 Front Panel Connector (CN26)
This is a front panel header (7x2-pin p=2.54mm).
Power LED
Pin 1 connects anode(+) of LED and pin 5 connects cathode(-) of LED. The power LED
lights up when the system is powered on. Pin 3 is defined as GND.
External Speaker and Internal Buzzer
Pin 2, 4, 6 and 8 connect the case-mounted speaker unit or internal buzzer. While
connecting the CPU board to an internal buzzer, please set pin 2 and 4 closed; while
connecting to an external speaker, you need to set pins 2 and 4 opened and connect the
speaker cable to pin 8(+) and pin 2(-).
Power On/Off Button
Pin 9 and 10 connect the power button on a front panel to the CPU board, which allows
users to turn on or off power supply.
System Reset Switch
Pin 11 and 12 connect the case-mounted reset switch that reboots your computer without
turning off the power switch. It is a better way to reboot your system for a longer life of
system power supply.
HDD Activity LED
This connection is linked to hard drive activity LED on the control panel. LED flashes
when HDD is being accessed. Pin 13 and 14 connect the hard disk drive to the front panel
HDD LED; pin 13 is assigned as cathode(-) and pin 14 is assigned as anode(+).
Pin
Signal
1
PWRLED+
2
EXT SPK-
3
GND
4
Buzzer
5
PWRLED-
6
N.C.
7
N.C.
8
EXT SPK+
9
PWRSW-
10
PWRSW+
11
HW RST-
12
HW RST+
13
HDDLED-
14
HDDLED+

SHB160 LGA1700 Full-size CPU Card
12 Board and Pin Assignments
2.4.4 DVI-I Connector (CN31)
DVI-I (integrated, combining digital and analog in the same connector; digital may be
single or dual link) provides transmission of fast and high quality digital video from a
source device (graphics card) to a display device.
Pin
Signal
Pin
Signal
1
DVI_DATA2-
2
DVI_DATA2+
3
GND
4
VGA_DDCSCL
5
VGA_DDCSDA
6
DVI_SPC
7
DVI_SPD
8
VGA_VSYNC_
R .
9
DVI_DATA1-
10
DVI_DATA1+
11
GND
12
N.C.
13
N.C.
14
+5V
15
GND
16
DVI_HTPLG
17
DVI_DATA0-
18
DVI_DATA0+
19
GND
20
N.C.
21
N.C.
22
GND
23
DVI_CLK+
24
DVI_CLK-
C1
Analog red
C2
Analog green
C3
Analog blue
C4
Analog
horizontal sync
C5
Analog ground

SHB160 LGA1700 Full-size CPU Card
Board and Pin Assignments 13
2.4.5 Internal USB 2.0 Connectors (CN33)
These are 5x2-pin P=2.54mm headers for USB 2.0 interface.
2.4.6 Rear I/O USB 3.2 (Gen2x1, 10Gbps) Connectors (CN35
and CN36)
These are standard USB (Universal Serial Bus) 3.0 connectors on the rear I/O for
connecting USB peripherals such as a keyboard, mouse, scanner, etc.
CN35: USB 3.2 port 0
CN36: USB 3.2 port 1
2.4.7 Internal PS/2 Keyboard and Mouse Connectors (CN28 and
CN29)
The board has two 5-pin connectors for PS/2 keyboard (CN29) and mouse (CN28)
interfaces.
Pin
Signal
Pin
Signal
1
USB2_PWR78
2
USB2_PWR78
3
USB _IN
4
USB _JN
5
USB _IP
6
USB _JP
7
GND
8
GND
10
GND
Pin
Signal
1
USB3_PWR12
2
D-
3
D+
4
GND
5
StdA_SSRX-
6
StdA_SSRX+
7
GND_DRAIN
8
StdA_SSTX-
9
StdA_SSTX+
Pin
Signal
1
Clock
2
DATA
3
No connector
4
GND
5
+5VDUAL

SHB160 LGA1700 Full-size CPU Card
14 Board and Pin Assignments
2.4.8 COM Connectors (COM1~COM4)
This is a 10 pin (Pitch = 2.54mm) connector which is compliant with CATCH 1137-000-
10S. and it supports RS-232/RS-422/RS-485 mode operation for COM1 ~ COM4. See
the table below for the pin assignments.
2.4.9 FAN Connectors (CPU FAN, FAN2 and FAN3)
Fans are needed for cooling down CPU and system temperature. The board has three
fan connectors. You can find fan speed option(s) at BIOS Setup Utility if fan is installed
via either connector. For further information, see BIOS Setup Utility: Advanced\HW
Monitor\PC Health Status.
Auxiliary and system fan interfaces are available through FAN2 and FAN3. See the table
below.
CPU fan interface is available through CPU FAN. See the table below.
Pin
RS-232
RS-422
RS-485
1
Data Carrier
Detect (DCD)
TX-
DATA-
2
Data Set Ready
(DSR)
No connector
No connector
3
Receive Data
(RXD)
TX+
DATA+
4
Request to Send
(RTS)
No connector
No connector
5
Transmit Data
(TXD)
RX+
No connector
6
Clear to Send
(CTS)
No connector
No connector
7
Data Terminal
Ready (DTR)
RX-
No connector
8
Ring Indicator
(RI)
No connector
No connector
9
Ground (GND)
GND
GND
10
Disconnect (NI)
NI
NI
Pin
Signal
1
GND
2
+12V level
3
Rotation detection
4
Speed Control
Pin
Signal
1
Ground
2
+12V
3
Rotation Detection
4
Speed Control