AXIOMTEK SHB211 Series User manual

SHB211 Series Quick Installation Guide
©Copyright 2009 AXIOMTEK Co., Ltd.
Version A1 March 2009
Printed in Taiwan
9418C211010E
4
LED will flash when the HDD is being accessed. Pins 13 and 14 can be
connected to the hard disk drive and front panel HDD LED.
V. Board Layout
Please refer to the SHB211 Series Product Information CD for the complete User’s Manual, drivers and utilities.
SHB211 Series Quick Installation Guide
©Copyright 2009 AXIOMTEK Co., Ltd.
Version A1 March 2009
Printed in Taiwan
9418C211010E
1
I. Checklist
9SHB211 Board x 1
9Quick Installation Guide x 1
9Product Information CD-ROM x 1
9COM, Printer Extension Cables with
Bracket x 1
92-pin Mini Jumper Caps x 12
9SATA Cable x 1
Note: Please contact your local vendors if any damaged or missing items. DO NOT
apply power to the board if any damaged components.
II. Jumper Settings
Before applying the power to SHB211 Series, please make sure all
jumper settings are defaulted as the following table:
¾COM1~COM2 Mode Select for Type Jumpers: JP5, JP6
COM1-PIN JP6 COM2 -PIN JP5
Pin 1=12V Short 1-3 Pin 1=12V Short 1-3
Pin 1=5V Short 3-5 or 5-7 Pin 1=5V Short 3-5 or 5-7
*Pin 1=DCD
(Default) Short 7-9 *Pin 1=DCD (Default) Short 7-9
Pin 8=12V Short 2-4 Pin 8=12V Short 2-4
Pin 8=5V Short 4-6 or 6-8 Pin 8=5V Short 4-6 or 6-8
*Pin 8=RI
(Default) Short 8-10 *Pin 8=RI (Default) Short 8-10
COM PORT SLOT JP5, JP6
Description Jumper Setting
CMOS Clear (JP19) Normal
(Default) Clear CMOS
Please refer to the SHB211 Series Product Information CD for the complete User’s Manual, drivers and utilities.

SHB211 Series Quick Installation Guide
©Copyright 2009 AXIOMTEK Co., Ltd.
Version A1 March 2009
Printed in Taiwan
9418C211010E
2
Description Function Jumper Setting
RS-232
(Default)
JP1
JP2
JP3
RS-422
JP1
JP2
JP3
COM1
RS-485
JP1
JP2
JP3
Description Jumper Setting
CF Device
(JP8~11) Enable
(Default) Disable
CF Device Voltage
Selection (JP12) 3.3V (Default) 5V
LVDS Voltage
Selection (JP18) 3.3V
(Default) 5V
USB Voltage
Selection
(JP14, JP15, JP17)
5V
(Default- JP17)
5V_SBY
(Default-
JP14, JP15)
North Bridge
PCIEx16 Signal
Mode
(JP20, JP21)
Display Port
(Default-
SHB211-
PGGA )
PCIEx16
(Default-
SHB211-
VGGA )
Auto-Power Button
Selection (JP13) Manual Power Button (Default)
Automatic
Power Button
Please refer to the SHB211 Series Product Information CD for the complete User’s Manual, drivers and utilities.
SHB211 Series Quick Installation Guide
©Copyright 2009 AXIOMTEK Co., Ltd.
Version A1 March 2009
Printed in Taiwan
9418C211010E
3
III. Connectors
Connectors Label Connectors Label
AUDIO CONNECTOR CN1 SATA1 PORT SATA1
Front Panel CONNECTOR CN2 SATA2 PORT SATA2
FDD / PARALLEL CONNECTOR CN3
ATX POWER CONNECTOR CN4 COMPACT FLASH
CONNECTOR SCF1
CPU FAN CONNECTOR CN5 Ethernet1 PORT LAN1
SM BUS CONNECTOR CN6 Ethernet 2 PORT LAN2
SYSTEM FAN CONNECTOR CN7 DDR3 SLOT1 DIMM1
SYSTEM FAN CONNECTOR CN8 DDR3 SLOT2 SDIMM
1
DISPLAY PORT(SHB211PGGA) CN9 USB1 PORT USB1
VGA PORT (SHB211VGGA) CN10 USB2 PORT USB2
LVDS CONNECTOR CN11 USB3 / 4 CONNECTOR USB3
LVDS Inverter CONNECTOR CN12 USB5 / 6 CONNECTOR USB4
COM1 PORT COM1 KEYBORD CONNECTOR KB1
COM2 PORT COM2 MOUSE CONNECTOR MS1
Thermal Sensor CONNECTOR JP22 Thermal Sensor CONNECTOR JP23
IV. Front Panel Connectors
Power LED
Pins 1, 3, 5 connect the system power LED indicator to its corresponding switch
on the case. Pin 1 is +, and pin 5 assigned to -. Pin 3 is defined as NC.
External Speaker and Internal Buzzer Connector
Pins 2, 4, 6, 8 can be connected to the case-mounted speaker unit or internal
buzzer.
Power Button
Pins 9 and 10 connect the front panel’s ATX power button to the card.
Hardware Reset
Pins 11 and 12 are designed for Hardware Reset.
HDD Activity LED
This connector extends to the hard drive activity LED on the control panel. This
Please refer to the SHB211 Series Product Information CD for the complete User’s Manual, drivers and utilities.