AXIOMTEK CAPA13R User manual

CAPA13R
AMD®RYZENTM Embedded
V1605B/V1807B 3.5”Board
User’s Manual

ii
Disclaimers
This manual has been carefully checked and believed to contain accurate information.
Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or any third
party’s rights, and any liability arising from such use.
Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy,
completeness or usefulness of any information in this document. Axiomtek does not make any
commitment to update the information in this manual.
Axiomtek reserves the right to change or revise this document and/or product at any time
without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted, in
any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,
without the prior written permission of Axiomtek Co., Ltd.
CAUTION
If you replace wrong batteries, it causes the danger of explosion. It is recommended by the
manufacturer that you follow the manufacturer’s instructions to only replace the same or
equivalent type of battery, and dispose of used ones.
Copyright 2020 Axiomtek Co., Ltd.
All Rights Reserved
January 2020, Version A1
Printed in Taiwan

iii
ESD Precautions
Computer boards have integrated circuits sensitive to static electricity. To prevent chipsets
from electrostatic discharge damage, please take care of the following jobs with precautions:
Do not remove boards or integrated circuits from their anti-static packaging until you are
ready to install them.
Before holding the board or integrated circuit, touch an unpainted portion of the system
unit chassis for a few seconds. It discharges static electricity from your body.
Wear a wrist-grounding strap, available from most electronic component stores, when
handling boards and components.
Trademarks Acknowledgments
Axiomtek is a trademark of Axiomtek Co., Ltd.
Intel®and Celeron®are trademarks of Intel Corporation.
Windows®is a trademark of Microsoft Corporation.
AMI is a trademark of American Megatrend Inc.
IBM, PC/AT, PS/2, VGA are trademarks of International Business Machines Corporation.
Other brand names and trademarks are the properties and registered brands of their
respective owners.

iv
Table of Contents
Disclaimers.....................................................................................................ii
ESD Precautions...........................................................................................iii
Chapter 1 Introduction............................................. 1
1.1 Features...............................................................................................2
1.2 Specifications......................................................................................2
1.3 Utilities.................................................................................................3
Chapter 2 Board and Pin Assignments.................... 5
2.1 Board Dimensions and Fixing Holes.................................................5
2.2 Board Layout.......................................................................................7
2.3 Installing Cooling Fan.........................................................................9
2.4 Jumper and Switch Settings ............................................................10
2.4.1 LVDS Voltage Selection (JP1)....................................................................11
2.4.2 Restore BIOS Optimal Defaults (SW1)......................................................11
2.4.3 Auto Power On (SSW1) .............................................................................11
2.5 Connectors........................................................................................12
2.5.1 LVDS Connector (CN1)............................................................................. 13
2.5.2 Front Panel Connector (CN2) ................................................................... 15
2.5.3 Inverter Connector (CN4).......................................................................... 15
2.5.4 USB 2.0 Wafer Connector (CN5).............................................................. 16
2.5.5 SIM Card Wafer Connector (CN7) ............................................................ 16
2.5.6 Digital I/O Connector (CN8) ...................................................................... 16
2.5.7 COM1 and COM2 Wafer Connectors (CN9 and CN11)............................ 17
2.5.8 M.2 2242/3042 Key B Connector (CN10) ................................................. 18
2.5.9 SATA Connector (CN12) ........................................................................... 19
2.5.10 M.2 2230 Key E Connector (CN13) .......................................................... 20
2.5.11 Ethernet Wafer Connectors (CN14 for LAN4 and CN16 for LAN3) .......... 21
2.5.12 SATA Power Connector (CN15)................................................................ 21
2.5.13 Audio Wafer Connector (CN17) ................................................................ 22
2.5.14 USB 3.1 Port (CN18)................................................................................. 22
2.5.15 DisplayPort Connector (CN19).................................................................. 23
2.5.16 HDMI Connector (CN20 and CN21).......................................................... 24
2.5.17 Ethernet Ports (CN22 and CN23) ............................................................. 24
2.5.18 ATX Power Connector (ATX1)................................................................... 25
2.5.19 Fan Connector (SCN1) ............................................................................. 25
2.5.20 DC +5V/15W Power Output Connector (SCN2) ....................................... 25

v
Chapter 3 Hardware Description ........................... 27
3.1 Microprocessors ...............................................................................27
3.2 BIOS ...................................................................................................27
3.3 System Memory.................................................................................27
3.4 I/O Port Address Map........................................................................28
3.5 Interrupt Controller (IRQ) Map .........................................................29
3.6 Memory Map ......................................................................................34
Chapter 4 AMI BIOS Setup Utility .......................... 35
4.1 Starting...............................................................................................35
4.2 Navigation Keys ................................................................................35
4.3 Main Menu..........................................................................................37
4.4 Advanced Menu.................................................................................38
4.5 Chipset Menu.....................................................................................50
4.6 Security Menu....................................................................................54
4.7 Boot Menu..........................................................................................55
4.8 Save & Exit Menu ..............................................................................56
Appendix A Watchdog Timer................................... 59
A.1 About Watchdog Timer.....................................................................59
A.2 How to Use Watchdog Timer............................................................59
A.3 Sample Program................................................................................60
Appendix B Digital I/O ............................................. 63
B.1 About Digital I/O................................................................................63
B.2 Digital I/O Programming ...................................................................63

vi
This page is intentionally left blank.

CAPA13R Capa Board
Introduction 1
Chapter 1
Introduction
The CAPA13R, a 3.5”board, supports AMD®RYZEN®Embedded V1605B/V1807B processor.
It delivers outstanding system performance through high-bandwidth interfaces, multiple I/O
functions for interactive applications and various embedded computing solutions.
The CAPA13R has one 260-pin unbuffered SO-DIMM socket for single channel DDR4
2400/3200 MHz memory with maximum capacity up to 16GB. There are four Gigabit/Fast
Ethernet ports, one SATA port with transfer rate up to 6Gb/s, two USB 3.1 Gen 2 super speed
compliant, two USB 2.0 high speed compliant, and HD audio link that can achieve the best
stability and reliability for industrial applications. Additionally, it provides you with unique
embedded features, such as two serial ports (one RS-232/422/485, one RS-232) and 3.5”form
factor that applies an extensive array of PC peripherals.

CAPA13R capa Board
2 Introduction
1.1 Features
AMD®RYZENTM quad core V1807B (3.35GHz) and V1605B (2.0GHz)
1 DDR4 SO-DIMM supports up to 16 GB memory capacity
2 USB 3.1 Gen 2 ports
2 USB 2.0 ports
2 COM ports
4 GbE LAN
1 M.2 Key B
1 M.2 Key E
+12V only DC-in supported
1.2 Specifications
CPU
AMD®RYZENTM quad core V1807B 3.35GHz.
AMD®RYZENTM quad core V1605B 2.0GHz.
Thermal Solution
Active.
Operating Temperature
-20oC~-60oC.
BIOS
American Megatrends Inc. UEFI (Unified Extensible Firmware Interface) BIOS.
64Mbit SPI Flash, DMI, Plug and Play.
PXE Ethernet Boot ROM.
System Memory
One 260-pin unbuffered DDR4 SO-DIMM socket.
Maximum up to 16GB DDR4 2400MHz memory for V1605B.
Maximum up to 16GB DDR4 3200MHz memory for V1807B.
Onboard Multi I/O
Controller: Fintek F81803.
Two serial ports:
- COM1 supports RS-232/422/485 by BIOS selecting.
- COM2 supports RS-232 only.
Serial ATA
One SATA-600 connector.
One M.2 Key B connector in 22x42
USB Interface
Two USB ports with fuse protection and complies with USB Spec. Rev. 3.1 Gen 2 in
Type A connector.
Two USB ports with fuse protection and complies with USB Spec. Rev. 2.0 in 2x5-pin
wafer connector.
Display
Two HDMI with resolution max. up to 3840x2160 @30Hz.
One DisplayPort supports DP++ with max. resolution 4096x2160 @60Hz.
One 2x20-pin connector for 18/24-bit single/dual channel LVDS with one 8-pin
inverter connector. LVDS resolution is up to 1920x1200 in 24-bit dual channels.

CAPA13R Capa Board
Introduction 3
Watchdog Timer
1~255 seconds or minutes; up to 255 levels.
Ethernet
Four LAN ports with Realtek RTL8111G support 1000/100/10Mbps Gigabit/Fast
Ethernet with Wake-on-LAN and PXE Boot ROM.
Audio
HD audio link without codec.
Expansion Interface
One M.2 Key E connector in 22x30.
Power Input
One 2x2-pin connector.
+12V DC-in only.
AT auto power on function supported.
Power Management
ACPI (Advanced Configuration and Power Interface).
Form Factor
3.5”form factor.
Note
All specifications and images are subject to change without notice.
1.3 Utilities
Graphics driver
Ethernet driver

CAPA13R capa Board
4 Introduction
This page is intentionally left blank.

CAPA13R Capa Board
Board and Pin Assignments 5
Chapter 2
Board and Pin Assignments
2.1 Board Dimensions and Fixing Holes
Top View

CAPA13R capa Board
6 Board and Pin Assignments
Bottom View
Side View

CAPA13R Capa Board
Board and Pin Assignments 7
2.2 Board Layout
Top View
Side View

CAPA13R capa Board
8 Board and Pin Assignments
Bottom View

CAPA13R Capa Board
Board and Pin Assignments 9
2.3 Installing Cooling Fan
Image below illustrates how to install cooling fan on CAPA13R.

CAPA13R capa Board
10 Board and Pin Assignments
2.4 Jumper and Switch Settings
Jumper is a small component consisting of jumper clip and jumper pins. Install jumper clip on 2
jumper pins to close. And remove jumper clip from 2 jumper pins to open. Below illustration
shows how to set up jumper.
Properly configure jumper and switch settings on the CAPA13R to meet your application
purpose. Below you can find a summary table of jumper, switch and onboard default settings.
Note
Once the default jumper or switch setting needs to be changed, please do it under
power-off condition.
Jumper and Switch
Description
Setting
JP1
LVDS Voltage Selection
Default: +3.3V Level
1-2 Close
SW1
Restore BIOS Optimal Defaults
Default: Normal Operation
Release
SSW1
Auto Power On
Default: Disable
1-2 Close

CAPA13R Capa Board
Board and Pin Assignments 11
2.4.1 LVDS Voltage Selection (JP1)
This is a 2x3-pin (pitch=2.0mm) jumper. The board supports voltage selection for flat
panel displays. Use JP1 to set LVDS connector (CN1) pin 1~6 VCCM to +3.3V, +5V or
+12V voltage level. To prevent hardware damage, before connecting please make sure
that input voltage of the flat panel is correct.
2.4.2 Restore BIOS Optimal Defaults (SW1)
Use SW1 to clear CMOS. Press the tact switch for at least 1 second to restore BIOS
optimal defaults.
2.4.3 Auto Power On (SSW1)
If SSW1 is enabled for power input, the system will be automatically power on without
pressing soft power button. If SSW1 is disabled for power input, it is necessary to
manually press soft power button to power on the system.
Function
Setting
+3.3V level (Default)
1-2 close
+5V level
2-4 close
Or
4-6 close
+12V level
5-6 close
Function
Setting
Normal (Default)
Release
Restore BIOS optimal defaults
Press
Function
Setting
Disable auto power on (Default)
1-2 close
Enable auto power on
2-3 close

CAPA13R capa Board
12 Board and Pin Assignments
2.5 Connectors
Signals go to other parts of the system through connectors. Loose or improper connection
might cause problems, please make sure all connectors are properly and firmly connected.
Here is a summary table of connectors on the hardware.
Connector
Description
CN1
LVDS Connector
CN2
Front Panel Connector
CN4
Inverter Connector
CN5
USB 2.0 Wafer Connector
CN7
SIM Card Wafer Connector
CN8
Digital I/O Connector
CN9, CN11
COM1 and COM2 Wafer Connectors
CN10
M.2 2242/3042 Key B Connector
CN12
SATA Connector
CN13
M.2 2230 Key E Connector
CN14, CN16
Ethernet Port 4 and Port 3 Wafer Connectors
CN15
SATA Power Connector
CN17
Audio Wafer Connector
CN18
USB 3.1 Port 1 and 2
CN19
DisplayPort Connector
CN20, CN21
HDMI Connectors
CN22, CN23
Ethernet Port 1 and 2
ATX1
ATX Power Connector
SCN1
Fan Connector
SCN2
DC +5V/15W Power Output Connector
DIMM1
DDR4 SO-DIMM Connector

CAPA13R Capa Board
Board and Pin Assignments 13
2.5.1 LVDS Connector (CN1)
This board has one 2x20-pin (pitch=1.0mm) connector for LVDS LCD interface. It is
strongly recommended to use the matching connector, JST SHDR-40VS-B, for LVDS
interface. The Pin 1~6 VCCM can be set to +3.3V, +5V or +12V using JP1 (see section
2.4.1). Please note that when making LVDS cable, the pin 2 of JST SHDR-40VS-B
connector should match the pin 1 of CN1.
18-bit single channel
Pin
Signal
Pin
Signal
1
VCCM
2
VCCM
3
VCCM
4
VCCM
5
VCCM
6
VCCM
7
N.C
8
N.C
9
GND
10
GND
11
N.C
12
N.C
13
N.C
14
N.C
15
GND
16
GND
17
N.C
18
N.C
19
N.C
20
N.C
21
GND
22
GND
23
Channel A D0-
24
N.C
25
Channel A D0+
26
N.C
27
GND
28
GND
29
Channel A D1-
30
N.C
31
Channel A D1+
32
N.C
33
GND
34
GND
35
Channel A D2-
36
Channel A CLK-
37
Channel A D2+
38
Channel A CLK+
39
GND
40
GND

CAPA13R capa Board
14 Board and Pin Assignments
24-bit single channel 18-bit dual channel
Pin
Signal
Pin
Signal
Pin
Signal
Pin
Signal
1
VCCM
2
VCCM
1
VCCM
2
VCCM
3
VCCM
4
VCCM
3
VCCM
4
VCCM
5
VCCM
6
VCCM
5
VCCM
6
VCCM
7
N.C
8
N.C
7
N.C
8
N.C
9
GND
10
GND
9
GND
10
GND
11
N.C
12
N.C
11
N.C
12
Channel B D0-
13
N.C
14
N.C
13
N.C
14
Channel B D0+
15
GND
16
GND
15
GND
16
GND
17
N.C
18
N.C
17
Channel B CLK-
18
Channel B D1-
19
N.C
20
N.C
19
Channel B CLK+
20
Channel B D1+
21
GND
22
GND
21
GND
22
GND
23
Channel A D0-
24
N.C
23
Channel A D0-
24
Channel B D2-
25
Channel A D0+
26
N.C
25
Channel A D0+
26
Channel B D2+
27
GND
28
GND
27
GND
28
GND
29
Channel A D1-
30
Channel A D3-
29
Channel A D1-
30
N.C
31
Channel A D1+
32
Channel A D3+
31
Channel A D1+
32
N.C
33
GND
34
GND
33
GND
34
GND
35
Channel A D2-
36
Channel A CLK-
35
Channel A D2-
36
Channel A CLK-
37
Channel A D2+
38
Channel A CLK+
37
Channel A D2+
38
Channel A CLK+
39
GND
40
GND
39
GND
40
GND
24-bit dual channel
Pin
Signal
Pin
Signal
1
VCCM
2
VCCM
3
VCCM
4
VCCM
5
VCCM
6
VCCM
7
N.C
8
N.C
9
GND
10
GND
11
Channel B D3-
12
Channel B D0-
13
Channel B D3+
14
Channel B D0+
15
GND
16
GND
17
Channel B CLK-
18
Channel B D1-
19
Channel B CLK+
20
Channel B D1+
21
GND
22
GND
23
Channel A D0-
24
Channel B D2-
25
Channel A D0+
26
Channel B D2+
27
GND
28
GND
29
Channel A D1-
30
Channel A D3-
31
Channel A D1+
32
Channel A D3+
33
GND
34
GND
35
Channel A D2-
36
Channel A CLK-
37
Channel A D2+
38
Channel A CLK+
39
GND
40
GND