Lanner electronics IAC-F847 Series User manual

IAC-F847 SERIES
Full- size SBC with DDR/VGA
/Dual Gigabit LAN/HISA for
Socket 478 Pentium Ⅳ
ⅣⅣ
ⅣProcessor
User's Manual

COPYRIGHT©
This document is a copyright of the original manufacturer, 2003. The original manufacturer
reserves the right to make improvements to the product(s) described in this manual at any
time without notice. This manual may not, in whole or in part, be photocopied, reproduced,
transcribed, translated, or transmitted in any form without the written consent of the
manufacturer, except for copies retained by the purchaser for backup purposes. All rights
reserved.
TRADEMARKSTM
Pentium®, CeleronTM are registered trademark of Intel Corporation.
The following are trademarks or registered trademarks of their respective companies: IBM,
Intel, AMD, VIA C3, Award, AMI, Microsoft, Windows, Windows NT, Novell, SCO, PC/104,
PICMG, ALI, UMC, SMC, Winbond. Products mentioned in this manual are mentioned for
identification purposes only. All names of products or services appearing in this manual are
the trademarks or registered trademarks of their respective organizations and companies.
Copyright 2003
Version: 1.0
Date: 2003/05/09

TABLE OF CONTENTS
CHAPTER 1 GENERAL INFORMATION...................................................................................................................1
1.1 INTRODUCTION ..........................................................................................................................................................1
1.2 FEATURES...................................................................................................................................................................1
1.3 SPECIFICATION ...........................................................................................................................................................2
1.4 UNPACK YOUR IAC-F847 SERIES AND ACCESSORY...................................................................................................2
1.5 BOARD LAYOUT .........................................................................................................................................................3
CHAPTER 2 INSTALLATION.......................................................................................................................................4
2.1 HARDWARE SETUP AND INSTALLATION ......................................................................................................................4
2.1.1 CPU Installation and Upgrading.......................................................................................................................4
2.1.2 System Memory Installation...............................................................................................................................5
2.1.3 Compact Flash Installation................................................................................................................................6
2.2 JUMPER SETTINGS AND CONNECTORS........................................................................................................................7
2.2.1 Board outline...................................................................................................................................................7
2.2.2 Jumper Settings Summary..................................................................................................................................8
2.2.3 I/O Connector Summary.....................................................................................................................................9
CHAPTER 3 BIOS SETUP............................................................................................................................................19
3.1 RUNNING PHOENIX AWARD BIOS .........................................................................................................................19
3.2 CMOS SETUP UTILITY ............................................................................................................................................20
3.3 STANDARD CMOS SETUP........................................................................................................................................22
3.4 BIOS FEATURES SETUP............................................................................................................................................25
3.5 CHIPSET FEATURES SETUP .......................................................................................................................................27
3.6 INTEGRATED PERIPHERALS ......................................................................................................................................29
3.7 POWER MANAGEMENT SETUP..................................................................................................................................31
3.8 PNP/PCI CONFIGURATION .......................................................................................................................................34
3.9 PC HEALTH STATUS (OPTIONAL) .............................................................................................................................36
3.10 LOAD OPTIMIZED DEFAULTS..................................................................................................................................37
3.11 SET SUPERVISOR / USER PASSWORD.......................................................................................................................38
3.12 SAVE & EXIT SETUP...............................................................................................................................................39
3.13 EXIT WITHOUT SAVING ..........................................................................................................................................40
CHAPTER 4 DRIVERS SUPPORT..............................................................................................................................41
4.1 USE YOUR DRIVER CD-ROM..................................................................................................................................41
4.2 FILE DIRECTORY ......................................................................................................................................................41
APPENDIX A WATCH-DOG TIMER..........................................................................................................................42
TERMS AND CONDITIONS........................................................................................................................................43

Chapter 1. Introduction
1
User’s Manual
Chapter 1 General Information
1.1 Introduction
The IAC-F847 Series is a Pentium 4 PICMG Single Board Computer specifically designed for 478-pin socket
Pentium 4 processor, AGP graphic, two 10/100Base-TX or Giga LAN Ethernets. This makes the IAC-F847 Series
a perfect solution for not only popular networking devices like Firewall, Gateway, and e-Server, but also CTI
(Computer Telephony Integration) equipments such as PBX, Digital Logger, etc.
IAC-F847, powered by Intel advanced 845 series chipset, and supports 478-pin socket Intel Pentium 4
processor. It supports Ultra DMA-33/66/100 for faster hard drive transmission speeds and contains health
monitor hardware. Featured with 533/400MHz FSB (Front-Side-Bus), the IAC-F847 is also capable of
providing 3 x the bandwidth than traditional Intel Pentium III platform.
Besides it’s outstanding bandwidth and processing capability, the 845GV Integrate with 4 x AGP can provide
IAC-F847 with the highest VGA performance available in the market. The IAC-F847 is also proved to be the
most reliable and stable networking platform with the on-board server level dual Intel Ethernet chips.
In addition, IAC-F847 features two IDE ports, one FDD port, two COM ports with one selectable
RS-232/422/485 and one multi-mode parallel port allows for more devices support and more flexibility. Other
standard features include one socket for Compact Flash, six USB headers and one IrDA header. IAC-F847 has
also incorporated Watchdog Timer that allows for monitoring ability to ensure system stability.
IAC-F847 Series is a high power & full engine Single Board Computer CPU card, carefully designed to be a
feature-rich SBC CPU card at a reasonable price, this board elegantly meets industry needs and saves time and
money by waiving the hassle of going through the extra effort and cost of additional I/O cards. Being
standards-compliant, it is proved to be a quality product with high performance and stability in a long run.
1.2 Features
!"Support high performance Socket 478 Intel®Pentium® 4 processors.
!"Intel® 845GV chipset with 533MHz FSB
!"Integrate Intel® AGP 4X Graphic that can share memory up to 64M
!"Dual Intel® 82540 for GbE; Co-layout Intel 82562(LAN1) and 82551(LAN2) for FE

Chapter 1. Introduction
2User’s Manual
1.3 Specification
IAC-F847 Series
1.4 Unpack your IAC-F847 Series and Accessory
Before you begin to install your card, please make sure that you received the following materials as listed
below:
!"IAC-F847 Series SBC x 1 pc Single Board Computer
!"Keyboard and Mouse Cable x 1 pc 6-pin Mini-Din PS/2 connector to 6pin PS/2 K/B+6pin PS/2
Mouse Cable
!"LPT/COM cable x 1 pc 26-pin to 25-pin Printer Cable with Bracket and Key
!"ATX Feature Cable x 1 pc 4-pin 40cm cable
!"FDD Cable x 1 pc 34 to 34-pin Cable with Key
!"Power Cable x 1 pc 20AWG Wire 1007 13 cm
!"ATA Cable x 1 pc ATA100 40P IDE Impendence with Key
!"Heat Sink + Fan Heat Sink + Fan 7 x9 x5.5 cm
!"Driver Utility CD-ROM x 1 pc Drivers & Utilities
!"User's Manual x 1 pc This User's Manual
!"Keyboard Extension Cable x 1 pc 5-pin Cable for Keyboard Extension
Processor IntelPentiumTM 4 / Celeron in Socket 478 processor, supports up to
3.06GHz(with Hyper Theading Technology) and above
Chipset Intel845GV chipset 82845GV 533MHz FSB GMCH + 82801DB ICH4
System Memory / RAM Two184-pin DIMM sockets, support up to 2GB DDR 200/266 SDRAM
without ECC Function (DDR266)
BIOS Phoenix AwardBIOS
Flash Memory Disk CF Type-II at solder side
VGA Controller Int. IntelGFX, DB15 connector
IDE Drive Interface Two 20!2 Box header, support up to four IDE devices / ATA-33/66/100
Floppy Drive Interface One 17!2 Box header, support up to two floppy devices
Serial Port One DB9 (COM1: RS-232) and one 5!2 Box header (COM2: RS-232)
Parallel Port One 13!2 Box header (SPP / EPP / ECP)
Bus Interface PCI/ISA bus (High-Driver)
RTC Internal RTC with LI Battery
Keyboard/Mouse Connector One mini-Din6 PS/2 keyboard/mouse connector and one 5-pin keyboard
header
Watchdog Timer 16-level time-out intervals for software
Universal Serial Bus Support six USB with header
IR Interface One IrDA compliant Infrared interface
Health Monitoring System Temperature Alarm Seneor
Operating Temperature 0 °C~60 °C
Storage Temperature -20 °C~70 °C
Dimensions 338 x 122 mm (13.3”!4.8”)

Chapter 1. Introduction
3
User’s Manual
1.5 Board Layout

Chapter 2. Installation
4User’s Manual
Chapter 2 Installation
2.1 Hardware Setup and Installation
2.1.1 CPU Installation and Upgrading
Step1: Locate the ZIP Socket and open it by first pulling the lever of socket upward.
Step2: Inset the CPU into the socket, Please keep the lever right angle when inserting CPU. When
inserting the CPU please note the correct orientation as shown. The notched corner should
point toward the end of the lever.

Chapter 2. Installation
5
User’s Manual
Step3: Push the lever down to close the socket.
Step4: Attach the heat sink onto the CPU and close the levers to fix the attachment.
Step5: Finally attach the FAN cable to the CPU FAN header.
2.1.2 System Memory Installation
Step1: Open latches of DIMM socket.
Step2: Insert the RAM module into the DIMM socket.
Step3: Press the latches into the notches of the RAM module.

Chapter 2. Installation
6User’s Manual
2.1.3 Compact Flash Installation

Chapter 2. Installation
7
User’s Manual
2.2 Jumper Settings and Connectors
2.2.1 Board outline
VGAA1 PKM1
CPU
DIMMC2
DIMMC1
FAN2
1
3
FAN1
FAN3
IDEB1
IDEB2
LPTA1
IRDA1
1
USBA1
KCN1
LANB1
COMA1
COMB1
SM1
2
1
16
15
2
1
16
15
LNB1
PS4P1
2
1
4
3
A
TXC1
CMOS1
PSW1
PLRS1
1
3
1
3
1
1
1
1
1
1
1
1
FDCA1
1
USBA2
USBA3
2
1
2
1
2
1
2
25

Chapter 2. Installation
8User’s Manual
2.2.2 Jumper Settings Summary
Jumper Function
CMOS1 Clear CMOS Data
SCF1 Master/Slave Select
PLRS1 Power LED,HD LED, Reset, Speaker Connector
"
""
"CMOS1: Clear CMOS Data
Description CMOS1
Normal (Default) 1-2
Clear CMOS 2-3
"
""
"PLRS1: Power LED,HD LED, Reset, Speaker Connector(11 Pin 2.54mm)
PIN NO. DESCRIPTION
1 Power LED +
2 Power LED +
3 GND
4 HDD LED +
5 HDD LED -
6 RESET SW +
7 RESET SW - (GND)
8 External Speaker -
9 Internal Buzzer -
10 NC
11 External Speaker +
Default : 8-9 (ON) Internal Buzzer
11
1
PLRS1
CMOS1
3
1
CMOS1
PLRS1

Chapter 2. Installation
9
User’s Manual
2.2.3 I/O Connector Summary
CONNECTOR FUNCTION
ATXC1 ATX Power Control connector
PSW1 ATX Power Button
IRDA1 IRDA1 Connector
FAN1,2,3 Pin FAN Connector
PS4P1 4-Pin Power Connector
KCN1 KB Connector ( 5-Pin Wafer)
PSW1 ATX Power Button
PKM1 Keyboard & Mouse Connector (Min Din)
VGAA1 VGA Connector (D-Sub Connector)
COMB1 RS232 Serial Port #1 Connector (Header)
COMB2 Serial Port #2 Connector (Header)
LPTA1 Parallel Port Connector (Header)
IDEB1 / IDEB2 IDE Connector (Header)
FDCA1 Floppy Interface Connector (Header)
4PSP1 ATX Power Connector for CPU
FAN1/2/3 Fan Connector
LANB1/2 LAN Connector
"ATXC1: For ATX Function
Pin No. Description
1 GND
2 +5V StandBy
3 GND
4 PSON
A
TXC1
1
4
A
TXC1

Chapter 2. Installation
10 User’s Manual
"
""
"PSW1: For ATX Power Button
Pin No. Description
1 PANSW
2 GND
"
""
"IRDA1: IRDA1 Connector.
Pin No. Description
1 VCC
2 NC
3 IRRX
4 GND
5 IRTX
PSW1
1
2
IRDA1
1
5
IRDA1
PSW1

Chapter 2. Installation
11
User’s Manual
"
""
"FAN1/ FAN2 /FAN3: Pin FAN Connector
Pin No. Description
1 Ground
2 +12V
3 FAN Status
"
""
"PS4P1: 4-Pin Power Connector (P4-4P Male )
Pin No. Description
1 GND
2 GND
3 +12V
4 +12V
1 3
4
2
PS4P1
FAN1/2/3
1
3
PS4P1
FAN1
FAN3
FAN2

Chapter 2. Installation
12 User’s Manual
"
""
"SM1: Sound/Mouse 2x8 Pin 2.0mm(Female/Male)
Pin No. Description Pin No. Description
1 ICH_SPKR 2 AC97
3 AC_RST- 4 VCC
5 SYNC 6 GND
7 SDINO 8 +3.3V
9 NC 10 GND
11 BITCLK 12 +5V STANDBY
13 SDOUT 14 NC
15 MSDAT 16 MSCLK
"
""
"LNB1: LAN 2x8 Pin 2.0mm Female（
（（
（Female/Male）
））
）
Pin No. Description Pin No. Description
1 AMDI0+ 2 ACTLD
3 AMDI0- 4 Vcc2_5
5 GND 6 3VSB
7 AMDI1+ 8 GND
9 AMDI1- 10 LNKLD
11 AMDI2+ 12 AMDI3+
13 AMDI2- 14 AMDI3-
15 LNK1G 16 LNK100
2
116
15
SM1
1
LNB1
15
16
2
LNB1
SM1

Chapter 2. Installation
13
User’s Manual
"
""
"USBA1, 2, 3: USB Port #1~#6 Connector 2x5 Pin 2.54mm
Pin No. Description Pin No. Description
1 USB_VCC 2 USB_VCC
3 USBD0- 4 USBD1-
5 USBD0+ 6 USBD1+
7 Ground 8 Ground
9 USB Port#1Ground 10 USB Port#2 Ground
"
""
"IDEB1, 2: IDE Interface Connector ( 40Pin 2.54mm Pitch Header )
Pin No. Description Pin No. Description
1 Reset # 2 Ground
3 Data 7 4 Data 8
5 Data 6 6 Data 9
7 Data 5 8
Data 10
9 Data 4 10
Data 11
11 Data 3 12 Data 12
13 Data 2 14 Data 13
15 Data 1 16 Data 14
17 Data 0 18 Data 15
19 Ground 20 Key
21 DMA REQ# 22 Ground
23 IOW # 24 Ground
25 IOR # 26 Ground
27 IOCHRDY 28 Ground
29 DMA ACK # 30 Ground
31 Interrupt 32 NC
33 SA1 34 PD80P / SD80P
35 SA0 36 SA2
37 HDC CS0 # 38 HDC CS1 #
39 HDD Active LED # 40 Ground
USBA1
USBA2
USBA3
USBA1/2/3
2
1
10
9
IDEB1 IDEB2

Chapter 2. Installation
14 User’s Manual
"
""
"FDCA1: Floppy Interface Connector ( Header )
Pin No. Description Pin No. Description
1 Ground 2 Density Select
3 Ground 4 KEY
5 Ground 6 DS1
7 Ground 8 Index #
9 Ground 10 Motor Enable A #
11 Ground 12 Drive Select B #
13 Ground 14 Drive Select A #
15 Ground 16 Motor Enable B #
17 Ground 18 Direction #
19 Ground 20 Step #
21 Ground 22 Write Data #
23 Ground 24 Write Gate #
25 Ground 26 Track 0 #
27 Ground 28 Write Protect #
29 NC 30 Read Data #
31 Ground 32 Head Side Select #
33 NC 34 Disk Change #
"
""
"LPTA1：
：：
：Parallel Connector ( 26 Pin 2.54mm Pitch Header )
Pin No. Description Pin No. Description
1 Strobe # 2 Auto Form Feed
3 Data0 4 Error #
5 Data1 6 Initialize #
7 Data2 8 Printer Select IN #
9 Data3 10 Ground
11 Data4 12 Ground
13 Data5 14 Ground
15 Data6 16 Ground
17 Data7 18 Ground
19 Acknowledge # 20 Ground
21 Busy 22 Ground
23 Paper Empty 24 Ground
25 Printer Select 26 KEY
FDCA1
1 2
34
33
LPTA1
1 2
26
25
FDCA1
LPTA1

Chapter 2. Installation
15
User’s Manual
"
""
"COMB1: Serial Port #2 Connector ( Header )
Description
Pin No. RS-232
1 Data Carrier Detect (DCDB #)
2 Data Set Ready (DSRB #)
3 Receive Data (RXDB)
4 Request To Send (RTSB #)
5 Transmit Data (TXDB)
6 Clear To Send (CTSB #)
7 Data Terminal Ready (DTRB #)
8 Ring Indicator (RIB #)
9 Ground
10 KEY
"
""
"CF1: Compact Flash Connector
Pin Description Pin Description
1 GND 26 CD1-
2 DATA3 27 DATA11
3 DATA4 28 DATA12
4 DATA5 29 DATA13
5 DATA6 30 DATA14
6 DATA7 31 DATA15
7 CE1# 32 CE2#
8 A10 33 VS1#
9 OE# 34 IOR#
10 A9 35 IOW#
11 A8 36 WE#
12 A7 37 READY#
13 CFVCC3 38 CFVCC3
14 A6 39 CSEL
15 A5 40 VS2#
16 A4 41 RESET
17 A3 42 WAIT#
18 A2 43 INPACK#
19 A1 44 REG#
20 A0 45 DASP#
21 DATA0 46 DIAG#
22 DATA1 47 DATA8
23 DATA2 48 DATA9
24 WP 49 DATA10
25 CD2- 50 GND
#Compact Flash supports “Master” only.
9
1
10
2
COMB1
COMB1
1
25
26
50
CF1
#CF1 is on the solder side

Chapter 2. Installation
16 User’s Manual
"KCN1: 5 Pin Keyboard Cable Connector
Pin No. Description
1 Keyboard Clock
2 Keyboard Data
3 NC
4 Ground
5 +5V
"
""
"PKM1: Keyboard & Mouse Connector ( Mini Din )
Pin No. Description
1 PS/2 Keyboard Data
2 PS/2 Mouse Data
3 Ground
4 + 5V
5 PS/2 Keyboard Clock
6 PS/2 Mouse Clock
15
KCN1
1 2
4
6 5
3
PKM1
KCN1
PKM1