AXIOMTEK SHB106 Series User manual

SHB106 Series
Intel®Socket 1155 Core™i7 / Core™i5 /
Core™i3 / Processor
PICMG®1.3 Full-Size CPU Card
User’s Manual

Disclaimers
This manual has been carefully checked and believed to contain
accurate information. Axiomtek Co., Ltd. assumes no responsibility for
any infringements of patents or any third party‟s rights, and any liability
arising from such use.
Axiomtek does not warrant or assume any legal liability or
responsibility for the accuracy, completeness or usefulness of any
information in this document. Axiomtek does not make any
commitment to update the information in this manual.
Axiomtek reserves the right to change or revise this document and/or
product at any time without notice.
No part of this document may be reproduced, stored in a retrieval
system, or transmitted, in any form or by any means, electronic,
mechanical, photocopying, recording, or otherwise, without the prior
written permission of Axiomtek Co., Ltd.
Caution
If you replace wrong batteries, it causes the danger of explosion. It is
recommended by the manufacturer that you follow the manufacturer‟s
instructions to only replace the same or equivalent type of battery, and
dispose of used ones.
Copyright 2011 Axiomtek Co., Ltd.
All Rights Reserved
September 2011, Version A2
Printed in Taiwan

ESD Precautions
Computer boards have integrated circuits sensitive to static electricity.
To prevent chipsets from electrostatic discharge damage, please take
care of the following jobs with precautions:
Do not remove boards or integrated circuits from their anti-static
Packaging until you are ready to install them.
Before holding the board or integrated circuit, touch an unpainted
portion of the system unit chassis for a few seconds. It discharges
static electricity from your body.
Wear a wrist-grounding strap, available from most electronic
Component stores, when handling boards and components.
Trademarks Acknowledgments
Axiomtek is a trademark of Axiomtek Co., Ltd.
Windows®is a trademark of Microsoft Corporation.
AMI are trademarks of American Megatrend Inc.
IBM, PC/AT, PS/2, VGA are trademarks of International Business
Machines Corporation.
Intel® Core™ i3 LGA1155 Desktop Processor,
Intel® Core™ i5 LGA1155 Desktop Processor,
Intel® Core™ i7 LGA1155 Desktop Processor,
are trademarks of Intel Corporation
Winbond is a trademark of Winbond Electronics Corp.
Other brand names and trademarks are the properties and registered
brands of their respective owners.

Table of Contents
CHAPTER 1 INTRODUCTION.......................................................................... 1
1.1 Specifications.......................................................................2
1.2 Utilities Supported................................................................4
CHAPTER 2 JUMPERS AND CONNECTORS................................................ 5
2.1 Board Dimension.................................................................5
2.2 Board Layout .......................................................................6
2.3 Jumper Settings...................................................................7
2.3.1 COM1 Mode Select Jumpers for RS232/422/485 (JP2, JP3,
JP4).....................................................................................7
2.3.2 Audio Ampliier Jumper (JP1)...............................................8
2.3.3 Clear ME Jumper (JP6) .......................................................8
2.3.4 PS/2 Power Jumper (JP7) ...................................................8
2.4 Connectors ..........................................................................9
2.4.1 SMBUS Connector (CN1)..................................................10
2.4.2 Floppy Disk Port Connector (CN2) ....................................11
2.4.3 Internal USB Connectors (CN3,CN4,CN5,CN6)................12
2.4.4 LAN2 LED Connectors (CN7)............................................13
2.4.5 LAN1 LED Connectors (CN8)............................................13
2.4.6 DB15 CRT Connector (CN10) Co-layout with CN11..........14
2.4.7 Display Port Connector (CN11) Co-layout with CN10........14
2.4.8 Front Panel Connector (CN12)..........................................15
2.4.9 PS/2 Keyboard, Mouse Connectors (CN13, CN14)...........16
2.4.10 External USB Port Connectors (CN17, CN18) ..................16
2.4.11 RS232/422/485 Pin Assignment (COM1)..........................17
2.4.12 COM Port RS-232 Pin Assignment (COM2)......................18
2.4.13 Intel®HD Audio Digital Header (AUDIO1).........................18
2.4.14 ATX 8 Pin 12V IN Connector (ATX1).................................19
2.4.15 A CPU fan is always needed for cooling CPU heat (FAN1)19
2.4.16 System & Auxiliary Fan Connectors (FAN2, FAN3) ..........19
2.4.17 Ethernet RJ-45 Connectors (LAN1, LAN2)........................20
2.4.18 Parallel Port Connector (PRINT1) Print Port Connector....21
2.4.19 SATA Connectors (SATA1 ,SATA2 ,SATA3 ,SATA4 ,SATA5 ,
SATA6)..............................................................................22
CHAPTER 3 HARDWARE INSTALLATION................................................ 23
3.1 Installing the Processor .....................................................23
3.2 Installing the Memory.........................................................32
CHAPTER 4 HARDWARE DESCRIPTION................................................... 33
4.1 Microprocessors ................................................................33
4.2 BIOS..................................................................................33
4.3 System Memory.................................................................33

4.4 I/O Port Address Map ........................................................34
4.5 Interrupt Controller (IRQ) Map...........................................35
CHAPTER 5 AMI BIOS UTILITY .................................................................... 37
5.1 Starting ..............................................................................37
5.2 Navigation Keys.................................................................37
5.3 Main Menu.........................................................................39
5.4 Advanced Menu.................................................................40
5.5 Chipset Menu.....................................................................52
5.6 Boot Menu .........................................................................55
5.7 Security Menu....................................................................57
5.8 Save & Exit Menu ..............................................................58
APPENDIX A WATCHDOG TIMER............................................................. 61
Watchdog Timer Setting .......................................................................61
APPENDIX B PCI IRQ ROUTING................................................................... 63
PICMG®PCI IRQ Routing.....................................................................63
APPENDIX C CONFIGURING SATA FOR RAID FUNCTION ................ 64
APPENDIX D iAMT SETTINGS..................................................................... 77
D.1 Entering MEBx...................................................................77
D.2 Set & Change Password....................................................78
D.3 Intel® iAMT Settings..........................................................80
D.4 iAMT Web Console............................................................85
APPENDIX E PICMG®v1.3 INTERFACE DEFINITION............................ 87

MEMO:

SHB106 LAG1155 Full-Size SBC User’s Manual
Introduction
1
CHAPTER 1
INTRODUCTION
The SHB106 PICMG®1.3 full-size Single Board Computer supports
LAG1155 socket for Intel® Core™ i3 Desktop Processor, Intel® Core™
i5 Desktop Processor, Core™ i7 Desktop Processor with 32nm
technology and Transfer Rate 1066/1333 MHz. The board integrates
Intel®Q67 chipset that delivers outstanding system performance
through high-bandwidth interfaces, multiple I/O functions for interactive
applications and various embedded computing solutions. There are two
240-pin DDR3 DIMM sockets for dual channel DDR3 1066/1333,
maximum memory capacity up to 8GB. The board also features dual
Gigabit Ethernet, two SATA-6.0Gb/s and four SATA-3.0Gb/s and SATA
RAID 0/1/5/10 by PCH. Fourteen USB 2.0 high speed compliant ports
and built-in Intel®HD Audio Digital Header can achieve the best
stability and reliability for industrial applications.

SHB106 LAG1155 Full-Size SBC User’s Manual
Introduction
2
1.1 Specifications
CPU
Intel® Core™ i3 Desktop Processor
Intel® Core™ i5 Desktop Processor
Intel® Core™ i7 Desktop Processor
System Chipset
Intel® Q67
CPU Socket
LAG1155 Socket
DRAM Transfer Rate
1066/1333 MHz
BIOS
AMI BIOS via SPI interface with socket
System Memory
Two 240-pin DDR3 1066/1333 DIMM sockets
Maximum up to 8GB DDR3 memory
L1, L2, L3 Cache: integrated in CPU
Onboard Multi-I/O
Parallel Port: one 26-pin 2.54-pitch box-header, SPP/EPP/ECP
supported
Serial Port: one for RS-232/422/485 with 10-pin, 2.54-pitch box-
header (COM1) and one port for RS-232 with 10-pin, 2.54-pitch
box-header (COM2)
Floppy controller: one 34-pin, 2.54-pitch box-header supports two
drives (1.44MB for each)
USB Interface
Ten USB ports compliant with USB Spec. Rev. 2.0 (2 ports on
rear I/O, 8 ports on board, 4 ports to SHB connector-C golden
fingers)

SHB106 LAG1155 Full-Size SBC User’s Manual
Introduction
3
Onboard Graphic
Intel® Arrandale integrated Graphic processing unit processors
which goes with Q67 chipset with,VGA,DisplayPort (co-lay with
VGA)
Memory Size --Intel® DVMT 5.0 supported; preallocated memory
for frame buffer option as OS option:
Windows XP:
* For Total System Memory < 1GB,
Graphics sharing memory = 128 MB Maximum;
* For 1 GB to 1.5 GB Total System Memory,
Graphics sharing memory = 512 MB Maximum;
* For 1.5 GB to 2 GB Total System Memory,
Graphics sharing memory = 768 MB Maximum;
* For 2 GB and Above Total System Memory,
Graphics sharing memory = 1GB Maximum.
Windows Vista:
* Graphics sharing memory max to 0.5* (OS Ram Size –512)
Resolution -- Analog output -- the analog port utilizes an
integrated 400MHz 24-bit RAMDAC that can directly drive a
standard progressive scan analog monitor up to a resolution of
2048x1536 pixels with 32-bit color at 75 Hz
Analog Output Interface -- CRT from DAC output via 15-pin D-
Sub connector on the edge; CRT always ON supported
Ethernet
The LAN1/LAN2 are Intel 82579LM with iAMT 7.0 / Intel 82574L
Ethernet controller support 10/100/1000 Mb/s
Serial ATA
Two Serial ATA-6Gb/s and Four Serial ATA-3Gb/s performance
and SATA RAID 0/1/5/10 by Q67

SHB106 LAG1155 Full-Size SBC User’s Manual
Introduction
4
Audio
10-pin 2.0 pin-header (Intel® HD Audio Digital Header)
Hardware Monitoring
Monitoring temperatures, voltages, and cooling fan status
Watchdog Timer
Reset Supported (1-255 level)
Dimensions
338mm x 126mm
Expansion interface:
1 PCI-E x16
1 PCI-E x4(or 4 PCI-E x1)
4 PCI
NOTE: All specifications and images are subject to change without notice.
1.2 Utilities Supported
Intel®Q67 Utility and Drivers
VGA Drivers
Ethernet Utility and Drivers
RAID Utility
iAMT Utility and Drivers
TPM Utility

SHB106 LAG1155 Full-Size SBC User’s Manual
Jumpers And Connectors
5
CHAPTER 2
JUMPERS AND CONNECTORS
2.1 Board Dimension

SHB106 LAG1155 Full-Size SBC User’s Manual
Jumpers And Connectors
6
2.2 Board Layout
1
20
40 57 3020101
A
K
Y
AK
BK
AY
BU
BU
A
50
AY AW
40 37 3539 33 31 2729 212325 17 1519 913 11 57 13
40 3739 313335
AU
AR AN AL
135791113151719212325
AJ
AG AE
AC AA
W
U R N L J G E C
2729
A
240 121
240 121
12
9
10
G
A C
A
Y
C
12
9
10
G
A C
A
Y
C
1
1 1
ATX1 DIMM1
DIMM2
FAN1
FAN2
FAN3
CN1
SATA1 SATA5
SATA3
SATA6
SATA4SATA2
U23
U21 CN12
CN6
C N
4
CN3
JP6
C N
5
JP7
LAN2
JP1
AUDIO
COM2
COM1
CN10
CN11
LAN1
CN17 CN18
CN14
CN13
PRINT1
CN2

SHB106 LAG1155 Full-Size SBC User’s Manual
Jumpers And Connectors
7
2.3 Jumper Settings
Proper jumper settings configure the SHB106 to meet your
application purpose. We are herewith listing a summary table of all
jumpers and default settings for onboard devices, respectively.
Jumper
Description
Jumper Setting
JP2
COM1 Mode Selection : RS-232
Short 3-5 , 4-6
JP3
COM1 Mode Selection : RS-232
Short 3-5 , 4-6
JP4
COM1 Mode Selection : RS-232
Short 1-2
JP1
Audio Amplifier Selection : Disable
Short 1-3 , 2-4
JP6
Clear ME : Normal
Short 1-2
JP7
PS/2 Power Selection : 5VSBY
Short 2-3
2.3.1 COM1 Mode Select Jumpers for RS232/422/485
(JP2, JP3, JP4)
These jumpers select the COM1 port‟s communication mode to
operate RS-232 or RS-422/485
Function
Jumper Setting
JP2
JP3
JP4
RS-232
(Default)
RS-422
RS-485

SHB106 LAG1155 Full-Size SBC User’s Manual
Jumpers And Connectors
8
2.3.2 Audio Ampliier Jumper (JP1)
Function
Jumper Setting
Disable
(Default)
Enable
2.3.3 Clear ME Jumper (JP6)
You may need to use this jumper to clear the ME if incorrect ME
settings.
Function
Jumper Setting
Normal
(Default)
Clear ME
2.3.4 PS/2 Power Jumper (JP7)
You may need to ues this jumper to into S3 situation in WinXP.
Function
Jumper Setting
5V
5VSBY
(Default)

SHB106 LAG1155 Full-Size SBC User’s Manual
Jumpers And Connectors
9
2.4 Connectors
Connectors connect this board with other parts of the system. Loose
or improper connection might cause problems. Make sure all
connectors are properly and firmly connected.
Here is a summary table shows you all connectors on the board.
Connector
Label
SMBUS
CN1
Floppy Connecter
CN2
USB Port 6/7
CN3
USB Port 8/9
CN4
USB Port 12/13
CN5
USB Port 10/11
CN6
LAN2 External LED
CN7
LAN1 External LED
CN8
VGA Port
CN10
Display Port (BOM Option)
CN11
Axiomtek Front Panel
CN12
Keyboard
CN13
Mouse
CN14
USB Port 5
CN17
USB Port 4
CN18
COM1 Connector
COM1
COM2 Connector
COM2
Audio Connector
AUDIO1
ATX Connecter
ATX1
CPU FAN
FAN1
SYS FAN
FAN2
AUX FAN
FAN3
RJ45 (WG82579LM)
LAN1

SHB106 LAG1155 Full-Size SBC User’s Manual
Jumpers And Connectors
10
Connector
Label
RJ45 (WG82574L)
LAN2
Print Connecter
PRINT1
SATA 0 6.0Gb(SATA3)
SATA1
SATA 1 6.0Gb(SATA3)
SATA2
SATA Port 2
SATA3
SATA Port 5
SATA4
SATA Port 3
SATA5
SATA Port 4
SATA6
2.4.1 SMBUS Connector (CN1)
Connector SMBUS CN1 is for SMBUS interface support.
Pin
Signal
1
CLOCK
2
N.C
3
GND
4
DATA
5
+5V

SHB106 LAG1155 Full-Size SBC User’s Manual
Jumpers And Connectors
11
2.4.2 Floppy Disk Port Connector (CN2)
The board provides a 34-pin header type connector, CN2, supporting
up to two floppy drives. The floppy drives may be any one of the
following types: 5.25" 360KB/1.2MB and 3.5" 720KB/1.44MB/2.88MB.
Pin
Signal
Pin
Signal
Pin
Signal
1
GND
2
Drive Density Select
3
GND
4
No connector
5
GND
6
No connector
7
GND
8
Index#
9
GND
10
Motor enable A#
11
GND
12
No connector
13
GND
14
Drive select A#
15
GND
16
No connector
17
GND
18
Direction#
19
GND
20
STEP#
21
GND
22
Write data#
23
GND
24
Write gate#
25
GND
26
Track 0 #
27
GND
28
Write protect#
29
No connector
30
Read data#
31
GND
32
Head selection#
33
No connector
34
Disk change#

SHB106 LAG1155 Full-Size SBC User’s Manual
Jumpers And Connectors
12
2.4.3 Internal USB Connectors (CN3,CN4,CN5,CN6)
The 10-pin standard Universal Serial Bus (USB) connectors,
CN3/4/5/6, on this board are for installing versatile USB interface
peripherals.
Pin
Signal
Pin
Signal
CN3
1
USB_PWR
2
USB_PWR
3
USB6-
4
USB7-
5
USB6+
6
USB7+
7
GND
8
GND
10
GND
Pin
Signal
Pin
Signal
CN4
1
USB_PWR
2
USB_PWR
3
USB8-
4
USB9-
5
USB8+
6
USB9+
7
GND
8
GND
10
GND
Pin
Signal
Pin
Signal
CN5
1
USB_PWR
2
USB_PWR
3
USB12-
4
USB13-
5
USB12+
6
USB13+
7
GND
8
GND
10
GND

SHB106 LAG1155 Full-Size SBC User’s Manual
Jumpers And Connectors
13
Pin
Signal
Pin
Signal
CN6
1
USB_PWR
2
USB_PWR
3
USB10-
4
USB11-
5
USB10+
6
USB11+
7
GND
8
GND
10
GND
2.4.4 LAN2 LED Connectors (CN7)
Pin
Signal
1
+ 3.3V
2
LINK_ACT LED(-)
3
100, Low Active
4
+3.3V
5
1000, Low Active
2.4.5 LAN1 LED Connectors (CN8)
Pin
Signal
1
+ 3.3V
2
LINK_ACT LED(-)
3
100, Low Active
4
+3.3V
5
1000, Low Active

SHB106 LAG1155 Full-Size SBC User’s Manual
Jumpers And Connectors
14
2.4.6 DB15 CRT Connector (CN10) Co-layout with
CN11
CN10 is a DB15 connector commonly used for the CRT Monitor.
Pin
Signal
Pin
Signal
Pin
Signal
1
Red
2
Green
3
Blue
4
N.C
5
GND
6
DETECT
7
GND
8
GND
9
VCC
10
GND
11
N.C
12
DDC DATA
13
Horizontal Sync
14
Vertical Sync
15
DDC CLK
15
6
11
10
15
2.4.7 Display Port Connector (CN11) Co-layout with
CN10
CN11 is a Standard Display Port Connector co-layout with CN10.
Pin
Signal
CN24
1
DPB_LANE0
2
GND
3
DPB_LANE0#
4
DPB_LANE1
5
GND
6
DPB_LANE1#
7
DPB_LANE2
8
GND
9
DPB_LANE2#
10
DPB_LANE3
11
GND