AXIOMTEK SHB150R Series User manual

SHB150R Series
Intel®Socket 1151 CoreTM i7/ i5/ i3
Processors PICMG®v1.3 Full-size
CPU Card
User’s Manual

ii
Disclaimers
This manual has been carefully checked and believed to contain accurate information.
Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or any third
party’s rights, and any liability arising from such use.
Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy,
completeness or usefulness of any information in this document. Axiomtek does not make any
commitment to update the information in this manual.
Axiomtek reserves the right to change or revise this document and/or product at any time
without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted, in
any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,
without the prior written permission of Axiomtek Co., Ltd.
CAUTION
Wrong type of batteries may cause explosion. It is recommended that users only replace with
the same or equivalent type of batteries as suggested by the manufacturer once properly
disposing of any used ones.
Copyright 2020 Axiomtek Co., Ltd.
All Rights Reserved
April 2020, Version A1
Printed in Taiwan

iii
ESD Precautions
Computer boards have integrated circuits sensitive to static electricity. To prevent chipsets
from electrostatic discharge damage, please take care of the following jobs with precautions:
Do not remove boards or integrated circuits from their anti-static packaging until you are
ready to install them.
Before holding the board or integrated circuit, touch an unpainted portion of the system
unit chassis for a few seconds. Doing so can discharge static electricity from your body.
Wear a grounding wrist strap, available from most electronic component stores, when
handling boards and components.
Trademarks Acknowledgments
Axiomtek is a trademark of Axiomtek Co., Ltd.
Intel®CoreTM i7/ i5/ i3 are trademarks of Intel Corporation.
Windows®is a trademark of Microsoft Corporation.
AMI is a trademark of American Megatrend Inc.
IBM, PC/AT, PS/2, and VGA are trademarks of International Business Machines Corporation.
Other brand names and trademarks are the properties and registered brands of their
respective owners.

iv
Table of Contents
Disclaimers.....................................................................................................ii
ESD Precautions...........................................................................................iii
Chapter 1 Introduction............................................. 1
1.1 Features...............................................................................................1
1.2 Specifications......................................................................................2
1.3 Packing list..........................................................................................3
Chapter 2 Board and Pin Assignments.................... 5
2.1 Board Layout.......................................................................................5
2.2 Block Diagram.....................................................................................6
2.3 Jumper Settings..................................................................................7
2.3.1 Auto Power On (JP3) .................................................................................. 8
2.3.2 Restore BIOS Optimal Defaults (JP2)......................................................... 8
2.4 Connectors ..........................................................................................9
2.4.1 Temperature Sensor Connector (CN1) (Optional) .................................... 10
2.4.2 Ethernet Ports (CN5)................................................................................. 10
2.4.3 Front Panel Connector (CN8) ....................................................................11
2.4.4 DVI-I Connector (CN8).............................................................................. 12
2.4.5 Internal USB 2.0 Connectors (CN10)........................................................ 13
2.4.6 Rear I/O USB 3.1 (Gen1) Connectors (CN12 and CN15)......................... 13
2.4.7 Internal PS/2 Keyboard and Mouse Connectors (CN13 and CN14)......... 13
2.4.8 COM Connectors (COM1~COM4)............................................................ 14
2.4.9 FAN Connectors (FAN1, FAN2 and FAN3) ............................................... 14
2.4.10 SATA 3.0 Connectors (SATA1~SATA6)..................................................... 15
2.4.11 Intel®HD Audio Digital Header (HDA1)..................................................... 15
2.4.12 ATX Power Connector (ATX1)................................................................... 15
2.4.13 Internal USB 3.1 Gen1 Connector (CN3).................................................. 16
2.4.14 TPM Pin Header (CN2)............................................................................. 16
2.4.15 Parallel Port Connector (PRINT1)............................................................. 17
2.4.16 M.2 2280 Key M NVMe SSD (CN4).......................................................... 18
2.4.17 Internal USB 3.1 Gen2 Connector (CN7).................................................. 19
2.4.18 Display Port 1.4 Connector (CN11)........................................................... 20
Chapter 3 Hardware Installation ........................... 22
3.1 Installing the Processor....................................................................22
3.2 Installing the Memory .......................................................................25

v
Chapter 4 Hardware Description ........................... 26
4.1 Microprocessors ...............................................................................26
4.2 BIOS ...................................................................................................26
4.3 System Memory.................................................................................26
Chapter 5 AMI BIOS Setup Utility .......................... 28
5.1 Starting...............................................................................................28
5.2 Navigation Keys ................................................................................28
5.3 Main Menu..........................................................................................30
5.4 Advanced Menu.................................................................................31
5.5 Chipset Menu.....................................................................................46
5.6 Security Menu....................................................................................49
5.7 Boot Menu..........................................................................................50
5.8 Save & Exit Menu ..............................................................................51
Appendix A Watchdog Timer................................... 54
A.1 About Watchdog Timer.....................................................................54
A.2 How to Use Watchdog Timer............................................................54
Appendix B PCI IRQ Routing ................................... 56
B.1 PICMG®PCI IRQ Routing..................................................................56
Appendix C Configuring SATA for RAID .................. 58
C.1 Configuring SATA Hard Drive(s) for RAID (Controller: Intel®
Q370/C246) ...................................................................................................58
Appendix D iAMT Settings ...................................... 66
D.1 Entering MEBx...................................................................................66
D.2 Set and Change Password...............................................................66
D.3 iAMT Settings ....................................................................................68
D.4 iAMT Web Console............................................................................71
Appendix E PICMG®v1.3 Interface Definition.......... 74
Appendix F TPM Module Installation...................... 80

vi
This page is intentionally left blank.

SHB150R LGA1151 Full-size CPU Card
Introduction 1
Chapter 1
Introduction
The SHB150R PICMG®v1.3 full-size Single Board Computer supports an LGA1151 socket for
Intel®CoreTM i7/ i5/ i3 desktop processors with 14nm technology and transfer rate 2400/ 2666
MHz. The board integrates an Intel®Q370/H310/C246 chipset that delivers outstanding
system performance through high-bandwidth interfaces, multiple I/O functions for interactive
applications and various embedded computing solutions. There are two 288-pin DDR4 DIMM
sockets for dual channel DDR4 2400/ 2666MHz with maximum memory capacity up to 64GB.
The board also features dual Gigabit Ethernet, SATA 6Gbps with SATA RAID
0/1/5/10(Q370/C246) by PCH, USB 2.0, and USB 3.1 (Gen1/Gen2) high speed compliant
ports and built-in Intel®HD Audio Digital Header to achieve the best stability and reliability for
industrial applications.
1.1 Features
LGA1151 socket 9th/8th Generation Intel®CoreTM processors up to 95W
Intel®Q370/H310/C246 PCH
2 DDR4 unbuffered DIMM max. up to 64GB memory capacity
Intel®iAMT (Q370/C246 PCH) and TPM2.0 module supported (optional)
PCIe Gen. 3 at 8GT/s supported
USB 3.1 (Gen2) supported (Q370/C246 PCH)

SHB150R LGA1151 Full-size CPU Card
2 Introduction
1.2 Specifications
CPU
LGA1151 socket 9th/8th Generation Intel® Core™ i7/i5/i3, Pentium® and Celeron®
processors (Coffee Lake Refresh) up to 95W
System Chipset
Intel®Q370
Intel®H310
Intel®C246
CPU Socket
LGA1151 socket
DRAM Transfer Rate
2400/ 2666 MHz
BIOS
AMI BIOS via SPI interface with socket
System Memory
Two 288-pin DDR4 2400/ 2666MHz DIMM sockets
Maximum up to 64GB DDR4 memory
Supports the memory with ECC function (C246 PCH)
L1, L2, L3 Cache: Integrated in CPU
Onboard Multi I/O
Serial ports: two RS-232/422/485 port in 2x5-pin (pitch=2.54mm) box-header (COM
1/2) and two RS-232 ports in 2x5-pin (pitch=2.54mm) box-header (COM 3/4)
Parallel Port: one 26-pin 2.54-pitch box-header; SPP/EPP/ECP supported
USB Interface
Q370
Two USB3.1 (Gen2) ports on internal box header
Two USB3.1 (Gen1) ports on rear I/O
Two USB3.1 (Gen1) ports on internal box header
Two USB2.0 ports on internal pin header
Four USB2.0 ports on SHB connector-C golden fingers
H310
Two USB3.1 (Gen1) ports on rear I/O
Two USB3.1 (Gen1) ports on internal box header
Two USB2.0 ports on internal pin header
Four USB2.0 ports on SHB connector-C golden fingers
C246
Two USB3.1 (Gen2) ports on internal box header
Two USB3.1 (Gen1) ports on rear I/O
Two USB3.1 (Gen1) ports on internal box header
Two USB2.0 ports on internal pin header
Four USB2.0 ports on SHB connector-C golden fingers
Onboard Graphics
Integrated Intel®HD graphics supporting DVI-I
DVI/VGA: Max. resolution is 1920x1200.
Internal DP1.4 Connector: Max resolution is 4096 x 2304. Must use with Axiomtek
DP kit.

SHB150R LGA1151 Full-size CPU Card
Introduction 3
Ethernet
LAN1/LAN2: Intel®i219LM with iAMT / Intel®i211AT Ethernet controller
Support 1000/100/10Mbps Gigabit/Fast Ethernet
Storage
Serial ATA:
Six SATA 3.0 ports (6Gbps performance) with SATA RAID 0/1/5/10 (Q370/C246)
Four SATA 3.0 ports (6Gbps performance) (H310)
One M.2 2280 Key M (Only for Q370, C246 version)
Audio
Supports HD audio interface as a 2x8 pin header
Supports audio kit AX93242 with MIC-in/Line-in/speaker-out (option kit)
Watchdog Timer
1~255 seconds or minutes; up to 255 levels
Hardware Monitoring
Monitoring temperatures, voltages and cooling fan status
Dimensions
338mm x 126mm
Expansion Interface
One PCI-Express x16 (Gen.3)
One PCI-Express x4 (or four PCI-Express x1) (Gen.3)
Four PCI
Note
All specifications and images are subject to change without notice.
1.3 Packing list
1 x slot CPU card
1 x Driver DVD
1 x SATA cable
1 x COM cable

SHB150R LGA1151 Full-size CPU Card
4 Introduction
This page is intentionally left blank.

SHB150R LGA1151 Full-size CPU Card
Board and Pin Assignments 5
Chapter 2
Board and Pin Assignments
2.1 Board Layout
Top View
Rear Panel I/O

SHB150R LGA1151 Full-size CPU Card
6 Board and Pin Assignments
2.2 Block Diagram
Q370/C246/H310

SHB150R LGA1151 Full-size CPU Card
Board and Pin Assignments 7
2.3 Jumper Settings
Ajumper is a small component consisting of a jumper clip and jumper pins. Install a jumper clip
on two jumper pins to close a jumper. Remove the jumper clip from two jumper pins to open a
jumper. The following illustration shows how to set up a jumper.
Before applying power to the SHB150R series, please make sure all of the jumpers are in
factory default position. Below you can find a summary table and onboard default settings.
Note
Turn off power before changing any default jumper settings.
Jumper
Description
Setting
JP3
Auto Power On
Default: Enable
1-2 Close
JP2
Restore BIOS Optimal Defaults
Default: Normal Operation
1-2 Close

SHB150R LGA1151 Full-size CPU Card
8 Board and Pin Assignments
2.3.1 Auto Power On (JP3)
If JP3 is enabled for power input, the system will be automatically power on without
pressing soft power button. If JP3 is disabled for power input, it is necessary to manually
press soft power button to power on the system.
2.3.2 Restore BIOS Optimal Defaults (JP2)
Put jumper clip to pin 2-3 for a few seconds then move it back to pin 1-2. Doing this
procedure can restore BIOS optimal defaults.
Function
Setting
Enable auto power on (Default)
1-2 close
Disable auto power on
2-3 close
Function
Setting
Normal operation (Default)
1-2 close
Restore BIOS optimal defaults
2-3 close

SHB150R LGA1151 Full-size CPU Card
Board and Pin Assignments 9
2.4 Connectors
Signals go to other parts of the system through connectors. Loose or improper connection
might cause problems. Make sure all connectors are properly and firmly connected. Here is a
summary table showing all connectors on the hardware.
Jumpers/Headers/Connectors
1
ATX Power Connector (ATX1)
17
Front Panel Connector (CN8)
2
DDR4 Socket (DIMM1.DIMM2)
18
Buzzer (BZ1)
3
Internal USB 3.1 Gen1 Connector (CN3)
19
Internal USB2.0 Headers (CN10)
4
TPM Pin Header (CN2)
20
RTC Battery Socket (BAT1)
5
FAN Connectors (FAN1)
21
FAN Connectors (FAN3)
6
FAN Connectors (FAN2)
22
9th/8th Intel® Coffee Lake LGA 1151 socket
7
Parallel Port Connector (PRINT1)
23
PICMG_1.3 Gold Finger
8
SATA 3.0 Connectors (SATA1~SATA6)
24
PICMG_1.3 Gold Finger
9
COM Connectors (COM1)
25
PICMG_1.3 Gold Finger
10
COM Connectors (COM2)
26
PICMG_1.3 Gold Finger
11
COM Connectors (COM3)
27
Internal PS/2 Mouse Connectors (CN13)
12
COM Connectors (COM4)
28
Internal PS/2 Keyboard Connectors (CN14)
13
Intel®HD Audio Digital Header (HDA1)
29
Temperature Sensor Connector (CN1)
14
Restore BIOS Optimal Defaults (JP2)
30
Internal USB 3.1 Gen2 Connector (CN7)
15
Auto Power On (JP3)
31
Display Port 1.4 Connector (CN11)
16
M.2 2280 Key M NVMe SSD (CN4)
Rear I/O Jumpers/Headers/Connectors
32
Ethernet Ports (CN5)
34
DVI-I Connector (CN9)
32
Ethernet Ports (CN5)
35
Rear I/O l USB 3.1 Gen1 Connectors (CN12
and CN15)

SHB150R LGA1151 Full-size CPU Card
10 Board and Pin Assignments
2.4.1 Temperature Sensor Connector (CN1) (Optional)
This is a 2-pin connector for temperature sensor (NTC thermistor) interface. The
thermistor value should be 10K and its B value is 3435K.
2.4.2 Ethernet Ports (CN5)
The board has two RJ-45 connectors: LAN1 (i219LM) and LAN2 (i211AT). Ethernet
connection can be established by plugging one end of the Ethernet cable into this RJ-45
connector and the other end (phone jack) to a 1000/100/10 Base-T hub.
LAN1 LAN2
Pin
Signal
1
Sensor Input
2
GND
Pin
1000
Base-T
100/10
Base-T
Description
L1
BI_DA+
TX+
Bidirectional or Transmit Data+
L2
BI_DA-
TX-
Bidirectional or Transmit Data-
L3
BI_DB+
RX+
Bidirectional or Receive Data+
L4
BI_DC+
N.C.
Bidirectional or Not Connected
L5
BI_DC-
N.C.
Bidirectional or Not Connected
L6
BI_DB-
RX-
Bidirectional or Receive Data-
L7
BI_DD+
N.C.
Bidirectional or Not Connected
L8
BI_DD-
N.C.
Bidirectional or Not Connected
A
Speed LED
1000: Orange
100/10: OFF/Green
B
Active Link LED (Yellow)
Off: No link
Blinking: Data activity detected

SHB150R LGA1151 Full-size CPU Card
Board and Pin Assignments 11
2.4.3 Front Panel Connector (CN8)
This is a front panel header (7x2-pin p=2.54mm).
Power LED
Pin 1 connects anode(+) of LED and pin 5 connects cathode(-) of LED. The power LED
lights up when the system is powered on. Pin 3 is defined as GND.
External Speaker and Internal Buzzer
Pin 2, 4, 6 and 8 connect the case-mounted speaker unit or internal buzzer. While
connecting the CPU board to an internal buzzer, please set pin 2 and 4 closed; while
connecting to an external speaker, you need to set pins 2 and 4 opened and connect the
speaker cable to pin 8(+) and pin 2(-).
Power On/Off Button
Pin 9 and 10 connect the power button on a front panel to the CPU board, which allows
users to turn on or off power supply.
System Reset Switch
Pin 11 and 12 connect the case-mounted reset switch that reboots your computer
without turning off the power switch. It is a better way to reboot your system for a longer
life of system power supply.
HDD Activity LED
This connection is linked to hard drive activity LED on the control panel. LED flashes
when HDD is being accessed. Pin 13 and 14 connect the hard disk drive to the front
panel HDD LED; pin 13 is assigned as cathode(-) and pin 14 is assigned as anode(+).
Pin
Signal
1
PWRLED+
2
EXT SPK-
3
GND
4
Buzzer
5
PWRLED-
6
N.C.
7
N.C.
8
EXT SPK+
9
PWRSW-
10
PWRSW+
11
HW RST-
12
HW RST+
13
HDDLED-
14
HDDLED+

SHB150R LGA1151 Full-size CPU Card
12 Board and Pin Assignments
2.4.4 DVI-I Connector (CN8)
DVI-I (integrated, combining digital and analog in the same connector; digital may be
single or dual link) provides transmission of fast and high quality digital video between a
source device (graphics card) and a display device.
Pin
Signal
Pin
Signal
1
DVI_DATA2-
2
DVI_DATA2+
3
GND
4
N.C.
5
N.C.
6
DVI_SPC
7
DVI_SPD
8
N.C.
9
DVI_DATA1-
10
DVI_DATA1+
11
GND
12
N.C.
13
N.C.
14
+5V
15
GND
16
DVI_HTPLG
17
DVI_DATA0-
18
DVI_DATA0+
19
GND
20
N.C.
21
N.C.
22
GND
23
DVI_CLK+
24
DVI_CLK-
C1
Analog red
C2
Analog green
C3
Analog blue
C4
Analog
horizontal sync
C5
Analog ground

SHB150R LGA1151 Full-size CPU Card
Board and Pin Assignments 13
2.4.5 Internal USB 2.0 Connectors (CN10)
These are 5x2-pin p=2.54mm headers for USB 2.0 interface.
2.4.6 Rear I/O USB 3.1 (Gen1) Connectors (CN12 and CN15)
These are standard USB (Universal Serial Bus) 3.0 connectors on the rear I/O for
installing USB peripherals such as a keyboard, mouse, scanner, etc.
CN12: USB 3.0 port 0
CN15: USB 3.0 port 1
2.4.7 Internal PS/2 Keyboard and Mouse Connectors (CN13 and
CN14)
The board has two 5-pin connectors for PS/2 keyboard (CN14) and mouse (CN13)
interfaces.
Pin
Signal
Pin
Signal
1
USB_PWR
2
USB_PWR
3
USB -
4
USB -
5
USB +
6
USB +
7
GND
8
GND
10
GND
Pin
Signal
1
VCC
2
D-
3
D+
4
GND
5
StdA_SSRX-
6
StdA_SSRX+
7
GND_DRAIN
8
StdA_SSTX-
9
StdA_SSTX+
Pin
Signal
1
Clock
2
DATA
3
No connector
4
GND
5
5VSBY

SHB150R LGA1151 Full-size CPU Card
14 Board and Pin Assignments
2.4.8 COM Connectors (COM1~COM4)
The board supports RS-232/RS-422/RS-485 mode operation for COM1 and COM2. See
the table below for the pin assignments. You can change the transmission mode from
BIOS setting. COM3 and COM4 support RS-232 only.
2.4.9 FAN Connectors (FAN1, FAN2 and FAN3)
Fans are needed for cooling down CPU and system temperature. The board has three
fan connectors. You can find fan speed option(s) at BIOS Setup Utility if either fan is
installed. For further information, see BIOS Setup Utility: Advanced\HW Monitor\PC
Health Status.
Auxiliary and system fan interfaces are available through FAN1 and FAN2. See the table
below.
3 1
CPU fan interface is available through FAN3. See the table below.
Pin
RS-232
RS-422
RS-485
1
Data Carrier
Detect (DCD)
TX-
DATA-
2
Data Set Ready
(DSR)
No connector
No connector
3
Receive Data
(RXD)
TX+
DATA+
4
Request to Send
(RTS)
No connector
No connector
5
Transmit Data
(TXD)
RX+
No connector
6
Clear to Send
(CTS)
No connector
No connector
7
Data Terminal
Ready (DTR)
RX-
No connector
8
Ring Indicator
(RI)
No connector
No connector
9
Ground (GND)
GND
GND
10
Disconnect (NI)
NI
NI
Pin
Signal
1
GND
2
+12V level
3
Rotation detection
Pin
Signal
1
Ground
2
+12V
3
Rotation Detection
4
Speed Control