AXIOMTEK SHB110 Series User manual

SHB110 Series
Intel®Core™2 Duo/ Core™Duo
Core™Solo/ PICMG 1.3 Full-Size
Single Board Computer
User’s Manual

ii
Disclaimers
This manual has been carefully checked and believed to contain
accurate information. AXIOMTEK Co., Ltd. assumes no responsibility
for any infringements of patents or any third party’s rights, and any
liability arising from such use.
AXIOMTEK does not warrant or assume any legal liability or
responsibility for the accuracy, completeness or usefulness of any
information in this document. AXIOMTEK does not make any
commitment to update the information in this manual.
AXIOMTEK reserves the right to change or revise this document
and/or product at any time without notice.
No part of this document may be reproduced, stored in a retrieval
system, or transmitted, in any form or by any means, electronic,
mechanical, photocopying, recording, or otherwise, without the prior
written permission of AXIOMTEK Co., Ltd.
CAUTION
If you replace wrong batteries, it causes the danger of explosion. It is
recommended by the manufacturer that you follow the manufacturer’s
instructions to only replace the same or equivalent type of battery,
and dispose of used ones.
©Copyright 2007 AXIOMTEK Co., Ltd.
All Rights Reserved
August 2007, Version A1
Printed in Taiwan

iii
ESD Precautions
Computer boards have integrated circuits sensitive to static electricity.
To prevent chipsets from electrostatic discharge damage, please take
care of the following jobs with precautions:
Do not remove boards or integrated circuits from their anti-static
packaging until you are ready to install them.
Before holding the board or integrated circuit, touch an unpainted
portion of the system unit chassis for a few seconds. It
discharges static electricity from your body.
Wear a wrist-grounding strap, available from most electronic
component stores, when handling boards and components.
Trademarks Acknowledgments
AXIOMTEK is a trademark of AXIOMTEK Co., Ltd.
Windows®is a trademark of Microsoft Corporation.
Phoenix & AWARD are trademarks of Phoenix Technology Ltd.
IBM, PC/AT, PS/2, VGA are trademarks of International Business
Machines Corporation.
Intel®Core™ 2 Duo/ Core™Duo/Core™Solo are trademarks of Intel
Corporation.
Winbond is a trademark of Winbond Electronics Corp.
Other brand names and trademarks are the properties and registered
brands of their respective owners.

iv
Table of Contents
Disclaimers........................................................................................................... ii
ESD Precautions ................................................................................................. iii
C h a p t e r 1.............................................................................................................. 1
Introduction................................................................................................................. 1
1.1 Specifications................................................................................. 2
1.2 Utilities Supported ......................................................................... 3
1.3 Block Diagram ................................................................................ 4
1.4 I/O Bracket ...................................................................................... 4
C h a p t e r 2.............................................................................................................. 5
Jumpers and Connectors .......................................................................................... 5
2.1 Board Dimensions.......................................................................... 5
2.2 Board Placement............................................................................ 6
2.3 Jumper Settings ............................................................................. 7
2.3.1 COM2 Mode Select Jumpers: JP2, JP3, JP4............................... 7
2.3.2 LVDS Voltage Setting Jumper: JP1.............................................. 8
2.3.3 Compact Flash Setting Jumper: JP6 (Optional).......................... 8
2.3.4 CMOS Clear Jumper: JP7.............................................................. 9
2.4 Connectors ................................................................................... 10
2.4.1 Printer Port Connector: PRN1..................................................... 11
2.4.2 Audio Output Connector: AUDIO1.............................................. 12
2.4.3 CD AUX IN Connector: AUX1 (4 pin)........................................... 12
2.4.4 ATX 4 Pin 12V In Connector: CN1............................................... 12
2.4.5 Serial Port Interface Connectors: COM1, COM2 ....................... 13
2.4.6 Floppy Disk Port Connector: FDD1 ............................................ 13
2.4.7 IDE Interface Connector: IDE1 .................................................... 14
2.4.8 LVDS Panel Connector: CN3....................................................... 15
2.4.9 LCD Inverter Power Connector: CN2.......................................... 16
2.4.10 CRT Connector: CN4.................................................................... 17
2.4.11 SATA Connectors: SATA1~2....................................................... 17
2.4.12 Ethernet Connector: LAN1/LAN2................................................ 18
2.4.13 USB Port Connectors: USB1~2................................................... 19
2.4.14 USB Connector: USB3/USB4 ...................................................... 19
2.4.15 Front Panel Connector: CN5 ....................................................... 20
2.4.16 Mouse/Keyboard Connectors: MS1/KB1.................................... 21
2.4.17 System Fan1/Fan 2 Connectors: FAN1/FAN2............................ 21
2.4.18 CPU Fan Connector: FAN3.......................................................... 21
C h a p t e r 3............................................................................................................ 23
Hardware Installation ............................................................................................... 23
3.1 Installing the Porcessor............................................................... 23
3.2 Installing CPU Cooler................................................................... 24
3.3 Installing the Memory................................................................... 26

v
C h a p t e r 4............................................................................................................ 27
Hardware Description .............................................................................................. 27
4.1 Microprocessors .......................................................................... 27
4.2 BIOS............................................................................................... 27
4.3 System Memory............................................................................ 27
4.4 I/O Port Address Map................................................................... 28
C h a p t e r 5............................................................................................................ 29
Award BIOS Utility.................................................................................................... 29
5.1 Entering Setup.............................................................................. 29
5.2 Control Keys................................................................................. 30
5.3 Getting Help.................................................................................. 30
5.4 The Main Menu ............................................................................. 31
5.5 Standard CMOS Setup Menu....................................................... 32
5.6 Advanced BIOS Features............................................................. 35
5.7 Advanced Chipset Features........................................................ 39
5.8 Integrated Peripherals ................................................................. 40
5.9 Power Management Setup........................................................... 45
5.10 PnP/PCI Configuration Setup...................................................... 48
5.11 PC Health Status .......................................................................... 50
5.12 Load Fail-Safe Defaults................................................................ 51
5.13 Load Optimized Defaults ............................................................. 52
5.14 Set Supervisor/User Password................................................... 52
5.15 Save & Exit Setup......................................................................... 53
5.16 Exit Without Saving...................................................................... 54
C h a p t e r 6............................................................................................................ 55
Installation of Drivers............................................................................................... 55
6.1 Installing Chipset Driver.............................................................. 55
6.2 Installing VGA Driver.................................................................... 58
6.3 Installing LAN Driver.................................................................... 62
6.4 Installing Audio Driver................................................................. 64
A p p e n d i x A......................................................................................................... 67
Watchdog Timer........................................................................................................ 67
A p p e n d i x B......................................................................................................... 69
Comparison Table .................................................................................................... 69

vi
MEMO

SHB110 Socket M Full-Size SBC User’s Manual
Introduction 1
C h a p t e r 1
Introduction
The SHB110 PICMG 1.3 full-size Single Board Computer supports
Intel®Core™2 Duo/ Core™Duo/Core™Solo processors with FSB
533/667 MHz. The board integrates chipsets Intel®945GME and
ICH7M-DH that deliver outstanding system performance through high-
bandwidth interfaces, multiple I/O functions for interactive applications
and various embedded computing solutions. There are two DDR2
DIMM sockets for dual channel DDR2 533/667, maximum memory
capacity up to 4GB. The board also features Ethernet 10/100/1000Mb,
Dual PCI-Express LAN, and two serial ATA channels for a tatal of two
serial ATA hard drives at maximum transfer rate up to 300MB/sec.
Four USB 2.0 Port and built-in high definition audio codec can
achieve the best stability and reliability for industrial applications.

SHB110 Socket M Full-Size SBC User’s Manual
Introduction
2
1.1 Specifications
zCPU: Intel®Core™2 Duo/ Core™Duo/Core™Solo,
processors
zSystem Chipset: Intel®945GME and ICH7M-DH
zCPU Socket: Socket M
zFront-Side Bus: 533/667 MHz
zBIOS
Award PnP Flash BIOS
zSystem Memory
Two x 240-pin DDR2 DIMM sockets
Maximum up to 4GB DDR2 memory
Support DDR533/667 memory
zL2 Cache: integrated in CPU
zIDE Interface
One IDE connector and up to two IDE devices, Ultra DMA
ATA33/66/100 supported
zFDD Interface
Supports up to two drives
zCompact Flash Socket (optional)
One Compact Flash®Type II Socket
zOnboard Multi-I/O
Parallel Port: one bi-directional with ECP/EPP/SPP support
Serial Port: one for RS-232 (COM1) and one port for
RS-232/422/485 (COM2)
zUSB Interface
Four USB ports compliant with USB Spec. Rev. 2.0
zVGA Controller
Intel®Graphic Media Accelerator 950 integrated on Intel®
945GME

SHB110 Socket M Full-Size SBC User’s Manual
Introduction 3
zEthernet
The LAN1/LAN2 is 82573L Ethernet controller support
10/100/1000 Mb
Dual PCI-Express LAN
zSerial ATA
Support Serial ATA/Serial ATA II
Two Serial ATA channels for a total of two Serial ATA hard
drives
Maximum transfer rate could up to 300MB/sec
zAudio
Realtek ALC203 Audio Codec onboard
zHardware Monitoring
Detection of CPU temperature, System temperature, Power
failure and Fan speed
zWatchdog Timer
Reset Support (1-255 level)
zDimensions: 338x 126mm (8 layer)
NOTE: All specifications and images are subject to change
without notice.
1.2 Utilities Supported
zIntel®945GME Utility and Drivers
zVGA Drivers
zEthernet Utility and Drivers
zAudio Utility and Drivers

SHB110 Socket M Full-Size SBC User’s Manual
Introduction
4
1.3 Block Diagram
Notice: 4 USB 2.0 Port built-in on Backplane
1.4 I/O Bracket

SHB110 Socket M Full-Size SBC User’s Manual
Jumpers and Connectors 5
C h a p t e r 2
Jumpers and Connectors
2.1 Board Dimensions

SHB110 Socket M Full-Size SBC User’s Manual
Jumpers and Connectors
6
2.2 Board Placement

SHB110 Socket M Full-Size SBC User’s Manual
Jumpers and Connectors 7
2.3 Jumper Settings
Proper jumer settings configure the SHB110 to meet your application
purpose.
2.3.1 COM2 Mode Select Jumpers: JP2, JP3, JP4
These jumpers select the COM2 port’s communication mode to
operate RS-232 or RS-422/485.
Description Function Jumper Setting
RS-232
(Default) JP2
JP3 JP4
RS-422 JP2 JP3
JP4
COM2
RS-485 JP2 JP3
JP4

SHB110 Socket M Full-Size SBC User’s Manual
Jumpers and Connectors
8
2.3.2 LVDS Voltage Setting Jumper: JP1
This Jumper is to select the voltage for LCD interface.
Description Function Jumper Setting
3.3V
(Default) JP1
LCD Voltage
Setting
5V JP1
2.3.3 Compact Flash Setting Jumper: JP6 (Optional)
Use this jumper to set Master/Slave Compact Flash interface.
Description Function Jumper Setting
Master
(Default) JP6
Compact
Flash
Setting
Slave JP6

SHB110 Socket M Full-Size SBC User’s Manual
Jumpers and Connectors 9
2.3.4 CMOS Clear Jumper: JP7
You may need to use this jumper is to clear the CMOS memory if
incorrect BIOS settings.
Description Function Jumper Setting
Normal
(Default) JP7
CMOS Clear
Clear
CMOS JP7

SHB110 Socket M Full-Size SBC User’s Manual
Jumpers and Connectors
10
2.4 Connectors
Connectors connect this board with other parts of the system. Loose or
improper connection might cause problems. Make sure all connectors
are properly and firmly connected.
Here is a summary table shows you all connectors on the board.
Function Connector Function Connector
Audio Output AUDIO1 FDD FDD1
AUX IN AUX1 P-ATA IDE IDE1
Battery Socket BT1 K/B connector KB1
ATX 4P 12V IN CN1 LAN1 RJ-45 LAN1
LCD Inverter Power CN2 LAN2 RJ-45 LAN2
LVDS Panel
Connector CN3 M/S connector MS1
CRT Connector CN4 Printer Port PRN1
Axiom Front Panel CN5 S-ATA Port1 SATA1
COM1 COM1 S-ATA Port2 SATA2
COM2 COM2 CPU Socket U12
DDR2 DIMM Slot 1 DDR1 USB Port 1 USB1
DDR2 DIMM Slot 2 DDR2 USB Port 2 USB2
System FAN1 FAN1 USB Port 3, 4 USB3
System FAN2 FAN2 CPU FAN FAN3

SHB110 Socket M Full-Size SBC User’s Manual
Jumpers and Connectors 11
2.4.1 Printer Port Connector: PRN1
Print Port Connector [Default]
This board has a multi-mode parallel port to support:
1. Standard Mode:
IBM PC/XT, PC/AT and PS/2™are compatible with bi-directional
parallel port.
2. Enhanced Mode:
Enhance parallel port (EPP) is compatible with EPP 1.7 and EPP 1.9
(IEEE 1284 compliant).
3. High Speed Mode:
Microsoft and Hewlett Packard extended capabilities port (ECP) is
IEEE 1284 compliant.
Pin Signal Pin Signal
1 Strobe# 2 Data 0
3 Data 1 4 Data 2
5 Data 3 6 Data 4
7 Data 5 8 Data 6
9 Data 7 10 Acknowledge #
11 Busy 12 Paper Empty #
13 Printer Select 14 Auto Form Feed #
15 Error # 16 Initialize #
17 Printer Select In # 18 GND
19 GND 20 GND
21 GND 22 GND
23 GND 24 GND
25 GND 26 GND
PRN1
2
4
6
1
3
5
78
9
11
13
15
10
12
14
16
17
19
21
23
25
18
20
22
24
26

SHB110 Socket M Full-Size SBC User’s Manual
Jumpers and Connectors
12
2.4.2 Audio Output Connector: AUDIO1
AUDIO1 is a 10-pin connector to support the audio interface.
Pin Signal Pin Signal
1 MIC-IN 2 GND
3 Line In L 4 GND
5 Line In R 6 GND
7 Audio Out L 8 GND
9 Audio Out R 10 GND
AUDIO1
2.4.3 CD AUX IN Connector: AUX1 (4 pin)
Pin Signal Pin Signal
1 Signal-
IN(Light) 2 GND
3 GND 4
Signal-
IN(Right)
AUX1
2.4.4 ATX 4 Pin 12V In Connector: CN1
You can connect it to the ATX12V power supply for CPU Core Voltage.
Note: Make sure your ATX12V power supply can provide 16A on
the +12V lead and at least 1A on the +5V standby lead
(+5VSB). The minimum recommended wattage is 250W or
300W for a fully configured system. The system may become
unstable and may experience difficulty powering up if the
power supply is inadequate.
Pin Signal
1 GND
2 GND
3 +12V
4 +12V
CN1

SHB110 Socket M Full-Size SBC User’s Manual
Jumpers and Connectors 13
2.4.5 Serial Port Interface Connectors: COM1, COM2
The serial interface for the board consists of COM1 port (COM1) and
COM2 (COM2) supports RS-232/RS422/RS485.
Pin Signal Pin Signal
1 Data Carrier Detect
(DCD) 2Data Set Ready (DSR)
3 Receive Data (RXD) 4 Request to Send (RTS)
5 Transmit Data (TXD) 6 Clear to Send (CTS)
7 Data Terminal Ready
(DTR) 8Ring Indicator (RI)
9 Ground (GND) 10 NC
COM1, COM2
2
4
6
1
3
5
78
910
2.4.6 Floppy Disk Port Connector: FDD1
The board provides a 34-pin header type connector, FDD1, supporting
up to two floppy drives. The floppy drives may be any one of the
following types: 5.25" 360KB/1.2MB and 3.5" 720KB/1.44MB/2.88MB.
Pin Signal Pin Signal Pin Signal
1 GND 2 Reduce write current 3 GND
4 N/C 5 GND 6 N/C
7 GND 8 Index # 9 GND
10 Motor enable A # 11 GND 12 Drive select B #
13 GND 14 Drive select A # 15 GND
16 Motor enable B # 17 GND 18 Direction #
19 GND 20 STEP # 21 GND
22 Write data # 23 GND 24 Write gate #
25 GND 26 Track # 27 GND
28 Write protect # 29 GND 30 Read data #
31 GND 32 Side 1 select # 33 GND
34 Disk change #

SHB110 Socket M Full-Size SBC User’s Manual
Jumpers and Connectors
14
FDD1
2.4.7 IDE Interface Connector: IDE1
The board provided one IDE Port to support maximum up to two IDE
devices.
Pin Description Pin Description Pin Description
1 Reset # 2 GND 3 Data 7
4 Data 8 5 Data 6 6 Data 9
7 Data 5 8 Data 10 9 Data 4
10 Data 11 11 Data 3 12 Data 12
13 Data 2 14 Data 13 15 Data 1
16 Data 14 17 Data 0 18 Data 16
19 GND 20 N/C 21 N/C
22 GND 23 IOW # 24 GND
25 IOR # 26 GND 27 IOCHRDY
28 N/C 29 N/C 30 GND-Default
31 Interrupt 32 N/C 33 SA1
34 N/C 35 SA0 36 SA2
37 HDC CS0 # 38 HDC CSI # 39 HDD Active #
40 GND