Axis AXIS A8207-VE Mk II User manual

AXIS A8207-VE Network Video Door Station
AXIS A8207-VE MkII Network Video Door Station
Electrical Wiring Drawings November 2019
© Axis Communications AB, 2019

1. To check relay state, go to:
Hardware > I/O ports > Relays
2. Click Edit.
3. Depending on your lock type, set
Normal state to:
Open circuit for a fail-secure lock
Closed circuit for a fail-safe lock
4. Click Save.
Configure relay state in
the product's webpage PoE+ Switch
Relay powered by PoE (12V)

1. To check relay state, go to:
Hardware > I/O ports > Relays
2. Click Edit.
3. Depending on your lock type, set
Normal state to:
Open circuit for a fail-secure lock
Closed circuit for a fail-safe lock
4. Click Save.
Configure relay state in
the product's webpage
Door1
Door2
PoE+ Switch
Two lock relays powered by PoE (12V)

1. To check relay state, go to:
Hardware > I/O ports > Relays
2. Click Edit.
3. Depending on your lock type, set
Normal state to:
Open circuit for a fail-secure lock
Closed circuit for a fail-safe lock
4. Click Save.
Configure relay state in
the product's webpage
Power
supply
Door1
Door2
PoE+ Switch
One relay powered by PoE (12V), one relay
powered by external power supply

1. To check relay state, go to:
Hardware > I/O ports > Relays
2. Click Edit.
3. Depending on your lock type, set
Normal state to:
Open circuit for a fail-secure lock
Closed circuit for a fail-safe lock
4. Click Save.
Configure relay state in
the product's webpage
Potential-free
contact
PoE+ Switch
Relay powered by PoE (12V), one relay
potential-free contact (door chimes etc.)

1. To check relay state, go to:
Hardware > I/O ports > Relays
2. Click Edit.
3. Depending on your lock type, set
Normal state to:
Open circuit for a fail-secure lock
Closed circuit for a fail-safe lock
4. Click Save.
Configure relay state in
the product's webpage
V+
COM
NO
NC
REX
PoE+ Switch
I/O
REL
12V
24V
Power 12V fail-secure lock
by PoE+ from door station

1. To check relay state, go to:
Hardware > I/O ports > Relays
2. Click Edit.
3. Depending on your lock type, set
Normal state to:
Open circuit for a fail-secure lock
Closed circuit for a fail-safe lock
4. Click Save.
Configure relay state in
the product's webpage PoE+ Switch
V+
COM
NO
NC
REX
Power
supply
I/O
REL
12V
24V
Power fail-secure lock
by external power supply

1. To check relay state, go to:
Hardware > I/O ports > Relays
2. Click Edit.
3. Depending on your lock type, set
Normal state to:
Open circuit for a fail-secure lock
Closed circuit for a fail-safe lock
4. Click Save.
Configure relay state in
the product's webpage
Potential-free
contact
PoE+ Switch
Relay powered by PoE (24V), one relay
potential-free contact (door chimes etc.)

Configuration in the
product's webpage
Reader
Reader protocol
OSDP
Card types Pin
Protocol
Save
READER I/O 1
DOOR IN 1 DOOR IN 2 LOCK
+MIC- +SPK-
AUDIO AUX
A- B+ A- B+ D0 D1 A- B+ A- B+ D0 D1
-12
VIO 3IO 4IO 5IO 6
READER DATA 1 READER DATA 2
DC IN
RELAY | PWR
*REL*- - 12
V24 V
- H1 - H2
- IN1 - IN2 - IN3 - IN4
- +
- 3V IO
1IO 2
READER I/O 2
-12
VIO
7IO 8IO 9IO 10
PoE+ Switch
Wire reader to door controller using OSDP

Reader protocol
Wiegand
Card types Pin
Protocol
1
Inputs used for LED control
Activate beeper
Input for beeper
Beeper
3
Input for LED1
1
Color for state low
Color for each state
red
Color for state high
green
Configuration in the
product's webpage
READER I/O 1
DOOR IN 1 DOOR IN 2 LOCK
+MIC- +SPK-
AUDIO AUX
A- B+ A- B+ D0 D1 A- B+ A- B+ D0 D1
-12
VIO 3IO 4IO 5IO 6
READER DATA 1 READER DATA 2
DC IN
RELAY | PWR
*REL*- - 12
V24 V
- H1 - H2
- IN1 - IN2 - IN3 - IN4
- +
- 3V IO
1IO 2
READER I/O 2
-12
VIO
7IO 8IO 9IO 10
PoE+ Switch
Wire reader to door controller using Wiegand