Axis Q6032-E PTZ User manual

ENGLISH DEUTSCH ITALIANO ESPAÑOL
INSTALLATION GUIDE
FRAN
Ç
AIS
AXIS Q6032-E PTZ Dome Network Camera

About this Document
This document includes instructions for installing the
AXIS Q6032-E PTZ Dome Network Camera on your
network. Previous experience of networking will be
beneficial when installing the product.
Legal Considerations
Video and audio surveillance can be prohibited by laws
that vary from country to country. Check the laws in
your local region before using this product for
surveillance purposes.
This product includes one (1) H.264 decoder license. To
purchase further licenses, contact your reseller.
Electromagnetic Compatibility (EMC)
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to
radio or television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or
more of the following measures: Re-orient or relocate
the receiving antenna. Increase the separation between
the equipment and receiver. Connect the equipment to
an outlet on a different circuit to the receiver. Consult
your dealer or an experienced radio/TV technician for
help. Shielded (STP) network cables must be used with
this unit to ensure compliance with EMC standards.
USA - This equipment has been tested and found to
comply with the limits for a Class B computing device
pursuant to Subpart B of Part 15 of FCC rules, which are
designed to provide reasonable protection against such
interference when operated in a commercial
environment. Operation of this equipment in a
residential area is likely to cause interference, in which
case the user at his/her own expense will be required to
take whatever measures may be required to correct the
interference.
Canada - This Class B digital apparatus complies with
Canadian ICES-003.
Europe - This digital equipment fulfills the
requirements for radiated emission according to limit B
of EN55022, and the requirements for immunity
according to EN55024 residential and commercial
industry.
Japan - This is a class B product based on the standard
of the Voluntary Control Council for Interference from
Information Technology Equipment (VCCI). If this is used
near a radio or television receiver in a domestic
environment, it may cause radio interference. Install and
use the equipment according to the instruction manual.
Australia - This electronic device meets the
requirements of the Radio communications
(Electromagnetic Compatibility) Standard AS/NZS
CISPR22.
Equipment Modifications
This equipment must be installed and used in strict
accordance with the instructions given in the user
documentation. This equipment contains no
user-serviceable components. Unauthorized equipment
changes or modifications will invalidate all applicable
regulatory certifications and approvals.
Liability
Every care has been taken in the preparation of this
document. Please inform your local Axis office of any
inaccuracies or omissions. Axis Communications AB
cannot be held responsible for any technical or
typographical errors and reserves the right to make
changes to the product and documentation without
prior notice. Axis Communications AB makes no
warranty of any kind with regard to the material
contained within this document, including, but not
limited to, the implied warranties of merchantability
and fitness for a particular purpose. Axis
Communications AB shall not be liable nor responsible
for incidental or consequential damages in connection
with the furnishing, performance or use of this material.
RoHS
This product complies with both the European
RoHS directive, 2002/95/EC, and the Chinese
RoHS regulations, ACPEIP.
WEEE Directive
The European Union has enacted a Directive
2002/96/EC on Waste Electrical and Electronic
Equipment (WEEE Directive). This directive is
applicable in the European Union member
states.
The WEEE marking on this product (see right) or its
documentation indicates that the product must not be
disposed of together with household waste. To prevent
possible harm to human health and/or the environment,
the product must be disposed of in an approved and
environmentally safe recycling process. For further
information on how to dispose of this product correctly,
contact the product supplier, or the local authority
responsible for waste disposal in your area.
Business users should contact the product supplier for
information on how to dispose of this product correctly.
This product should not be mixed with other commercial
waste.
Support
Should you require any technical assistance, please
contact your Axis reseller. If your questions cannot be
answered immediately, your reseller will forward your
queries through the appropriate channels to ensure a
rapid response. If you are connected to the Internet, you
can:
• download user documentation and firmware updates
• find answers to resolved problems in the FAQ database.
Search by product, category, or phrases
• report problems to Axis support by logging in to your
private support area.
The AXIS Q6032-E uses a 3.0V CR2032 Lithium
battery, for more information please see page 69.

AXIS Q6032-E Installation Guide Page 3
ENGLISH
AXIS Q6032-E Installation Guide
This installation guide provides instructions for installing the AXIS Q6032-E Network Camera on
your network. For all other aspects of using the product, please see the User’s Manual, available on
the CD included in this package, or from www.axis.com/techsup
Installation steps
1. Check the package contents against the list below.
2. Hardware overview. See page 4.
3. Install the hardware. See page 5.
4. Assign an IP address. See page 7.
5. Set the password. See page 10.
Package contents
Item Models/variants/notes
Network camera AXIS Q6032-E 50Hz/60Hz
Dome covers • Clear transparent cover
• Smoked transparent cover
High PoE Midspan AXIS T8124 including power cable (country specific)
RJ45 connector IP66 rated network connector
Sunshield Plastic protective cover, including screws
Labels 2 adhesive serial number labels
CD AXIS Network Video Product CD, including product documentation,
installation tools and other software
Printed materials AXIS Q6032-E Installation Guide (this document)
Axis Warranty Document
Optional accessories See www.axis.com for information on available mounting brackets
Important!
This product must be used in
compliance with local laws and
regulations.

Page 4 AXIS Q6032-E Installation Guide
Hardware overview
Part number (P/N) & Serial number (S/N).
The serial number may be required
during the installation.
Status indicator LED
Control button
Unit holders (3)
Network connector (PoE)
Hook for
safety wire
Sunshield
Dome camera
SD memory card slot
Power button
(for Factory Default only)
Dome cover
Rubber
gasket
Metal
ring
Dome ring
Holes for unit holders
Screw holes
Screws (4)
Caution!
Heater
may be hot

AXIS Q6032-E Installation Guide Page 5
ENGLISH
Install the hardware
Before installation
AXIS Q6032-E is supplied with an optional sunshield and smoked transparent dome cover. If
required, follow these instructions to attach the sunshield and replace the dome cover.
Attach the sunshield (optional)
1. Slide the sunshield over the unit holders on the dome camera unit.
2. Secure the sunshield using the supplied screws (Torx T20).
Replace the clear/smoked dome cover (optional)
1. Remove the 4 screws (see illustration on page 4).
2. Remove the metal ring and dome ring from the plastic dome cover.
3. Remove the rubber gasket from the dome cover and attach it to the selected dome cover. Be
sure to attach the gasket so it fits the dome cover perfectly.
4. Attach the metal ring and dome ring and secure by tightening the 4 screws to the maximum
stop.
Note:
Be careful not to scratch or damage the dome cover. Use a soft cloth to wipe clean before
attaching the dome cover to the camera unit.
Install the AXIS Q6032-E
Important!
The supplied RJ45 connector or compatible, IP66 rated RJ45 connector must be used in
order to comply with the IP66 rated design of the camera.
1. Install the selected mounting accessories according to the instructions and remove the protec-
tion cap covering the network connector on the camera.
2. Route the network cable and attach the supplied
RJ45 connector. Refer to the instructions provided
with the connector for information on wiring and
assembly.
3. Hook the dome camera unit to the safety wire on
the bracket.
4. Connect the network cable and RJ45 connector to
the network connector on the dome camera unit.
5. Slide the unit holders on the camera into the slots
on the bracket and rotate the camera unit.
6. Secure the dome camera unit to the mounting
bracket by fastening the 3 screws (Torx T30).
Wall bracket (mounting example)
Safety
wire
Slots for
Screws
Torx T30
unit holders

Page 6 AXIS Q6032-E Installation Guide
Install the AXIS T8124 Midspan
The Axis High PoE midspan enables Axis network video products with high power consumption to
receive data and power over the same Ethernet cable. Follow these instructions to connect the
AXIS T8124 and AXIS Q6032-E.
Note:
Note that Axis can only guarantee full functionality with the AXIS T8124, no other High
PoE devices are supported.
1. Connect the AXIS T8124 (Data in) to the network switch using a standard network cable.
2. Connect the AXIS T8124 (Data and Power Out) to the AXIS Q6032-E, using the network cable
that has been connected to the camera (see above).
3. Connect the AXIS T8124 to an AC outlet (100-240 VAC), using the supplied power cable.
AXIS T8124 Indicators
AXIS Q6032-E Status LED
LED Color Indication
Port Unlit No camera connected
Amber Insufficient power for camera and heater. Check cable
Flashing Power overload
Green Camera connected, normal behavior
AC input Steady green AC power connected
Color Indication
Unlit Steady connection/normal operation
Amber Steady for system initiating. Flashes during firmware upgrade or reset to factory default.
Amber/red No network connection
Red Firmware upgrade failure
Green Steady for 10sec. after successful restart
Ethernet
Data and
Data in
Port
indicator
AC Input
indicator
Power out
AXIS Q6032-E
connectivity
connectivity
AXIS T8124

AXIS Q6032-E Installation Guide Page 7
ENGLISH
Assign an IP address
Most networks have a DHCP server that automatically assigns IP addresses to connected devices. If
your network does not have a DHCP server the AXIS Q6032-E will use 192.168.0.90 as the default
IP address.
If you would like to assign a static IP address, the recommended method in Windows is either AXIS
IP Utility or AXIS Camera Management. Depending on the number of cameras you wish to install,
use the method that best suits your purpose.
Both of these free applications are available on the Axis Network Video Product CD supplied with
this product, or they can be downloaded from www.axis.com/techsup
Notes:
• If assigning the IP address fails, check that there is no firewall blocking the operation.
• For other methods of assigning or discovering the IP address of the AXIS Q6032-E e.g. in other
operating systems, see page 12.
Method Recommended for Operating system
AXIS IP Utility (version 2)
See page 8
Single camera
Small installations
Windows Vista
Windows Server 2003
Windows XP
Windows 2000
Windows NT 4.0
AXIS Camera Management
See page 9
Multiple cameras
Large installations
Installation on a different subnet
Windows Vista
Windows Server 2003
Windows XP Pro
Windows 2000

Page 8 AXIS Q6032-E Installation Guide
AXIS IP Utility - single camera/small installation
AXIS IP Utility automatically discovers and displays Axis devices on your network. The application
can also be used to manually assign a static IP address.
Note that the computer running AXIS IP Utility must be on the same network segment (physical
subnet) as the AXIS Q6032-E.
Automatic discovery
1. Check that the camera is connected to the network and that power has been applied.
2. Start AXIS IP Utility.
3. When the camera appears in the window, double-click it to open its home page.
4. See page 10 for instructions on how to assign the password.
Assign the IP address manually (optional)
1. Acquire an unused IP address on the same network segment as your computer.
2. Select the AXIS Q6032-E in the list.
3. Click the button Assign new IP address to the selected device and enter the IP address.
4. Click the Assign button and follow the on-screen instructions. Note that the camera must be
restarted within 2 minutes for the new IP address to be set.
5. Click the Home Page button to access the camera’s web pages.
6. See page 10 for instructions on how to set the password.

AXIS Q6032-E Installation Guide Page 9
ENGLISH
AXIS Camera Management - multiple cameras/large installations
AXIS Camera Management can automatically discover multiple Axis devices, show connection
status, manage firmware upgrades and set IP addresses.
Automatic discovery
1. Check that the camera is connected to the network and that power has been applied.
2. Start AXIS Camera Management. When the AXIS Q6032-E appears in the window, right-click
the link and select Live View Home Page.
3. See page 10 for instructions on how to set the password.
Assign an IP address in a single device
1. Select AXIS Q6032-E in AXIS Camera Management and click
the Assign IP button.
2. Select Assign the following IP address and enter the IP
address, subnet mask and default router the device will use.
3. Click the OK button.
Assign IP addresses in multiple devices
AXIS Camera Management speeds up the process of assigning IP
addresses to multiple devices, by suggesting IP addresses from a
specified range.
1. Select the devices you wish to configure (different models can
be selected) and click the Assign IP button.
2. Select Assign the following IP address range and enter the
range of IP addresses, the subnet mask and default router the
devices will use.
3. Click the OK button.

Page 10 AXIS Q6032-E Installation Guide
Set the password
To gain access to the product, the password for the default administrator user root must be set. This
is done in the ‘Configure Root Password’ dialog, which is displayed when the AXIS Q6032-E is
accessed for the first time.
To prevent network eavesdropping when setting the root password, this can be done via an
encrypted HTTPS connection, which requires an HTTPS certificate (see note below).
To set the password via a standard HTTP connection, enter it directly in the first dialog shown
below.
To set the password via an encrypted HTTPS connection, follow these steps:
1. Click the Create self-signed certificate button.
2. Provide the requested information and click OK. The certificate is created and the password can
now be set securely. All traffic to and from the AXIS Q6032-E is encrypted from this point on.
3. Enter a password and then re-enter it to confirm the spelling. Click OK. The password has now
been configured.
4. To log in, enter the user name “root” in the dialog as requested
Note: The default administrator user name root cannot be deleted.
5. Enter the password as set above, and click OK.
To configure the password directly
via an unencrypted connection, enter
the password here.
To create an HTTPS connection,
start by clicking this button.

AXIS Q6032-E Installation Guide Page 11
ENGLISH
Access the video stream
The Live View page of the AXIS Q6032-E is displayed, with links to the Setup tools, which allow you
to customize the camera.
If required, click Yes to install AMC (AXIS Media Control), which allows viewing of the video stream
in Internet Explorer. You will need administrator rights on the computer to do this.
Note:
To install AMC in Windows Vista, you must run Internet Explorer as administrator. Right-
click the Internet Explorer icon and select Run as administrator.
Notes:
• HTTPS (Hypertext Transfer Protocol over Secure Socket Layer) is a protocol used to encrypt the traffic
between web browsers and servers. The HTTPS certificate controls the encrypted exchange of
information.
• The default administrator user root cannot be deleted.
• If the password for root is lost or forgotten, the AXIS Q6032-E must be reset to the factory default
settings. See Resetting to the Factory Default Settings, on page 14.
Setup - Provides all the
tools for configuring the
camera to requirements.
Help - Displays
online help on all
aspects of using
the camera.

Page 12 AXIS Q6032-E Installation Guide
Other methods of setting the IP address
The table below shows the other methods available for setting or discovering the IP address. All
methods are enabled by default, and all can be disabled.
Set the IP address with ARP/Ping
1. Acquire an IP address on the same network segment your computer is connected to.
2. Locate the serial number (S/N) on the product label on the camera.
3. Open a command prompt on your computer and enter the following commands:
4. Check that the network cable is connected to the camera and then start/restart the camera, by
disconnecting and reconnecting power.
5. Close the command prompt when you see ‘Reply from 192.168.0.125: ...’ or similar.
6. In your browser, type in http://<IP address> in the Location/Address field and press Enter on
your keyboard.
Notes:
• To open a command prompt in Windows: from the Start menu, select Run... and type cmd. Click OK.
• To use the ARP command in Windows Vista, right-click the command prompt icon and select Run as
administrator.
• To use the ARP command on a Mac OS X, use the Terminal utility in Application > Utilities.
Use in operating
system
Notes
UPnP™ Windows
(ME or XP)
When enabled on your computer, the camera is automatically
detected and added to “My Network Places.”
Bonjour MAC OSX
(10.4 or later)
Applicable to browsers with support for Bonjour. Navigate to the
Bonjour bookmark in your browser (e.g. Safari) and click on the
link to access the camera’s web pages.
AXIS Dynamic DNS
Service
All A free service from Axis that allows you to quickly and simply
install your camera. Requires an Internet connection with no
HTTP proxy. See www.axiscam.net for more information.
ARP/Ping All See below. The command must be issued within 2 minutes of
connecting power to the camera.
View DHCP server
admin pages
All To view the admin pages for the network DHCP server, see the
server’s own documentation.
Windows syntax: Windows example:
arp -s <IP Address> <Serial Number>
ping -l 408 -t <IP Address> arp -s 192.168.0.125 00-40-8c-18-10-00 ping -l 408 -t 192.168.0.125
UNIX/Linux/Mac syntax: UNIX/Linux/Mac example:
arp -s <IP Address> <Serial Number> temp
ping -s 408 <IP Address> arp -s 192.168.0.125 00:40:8c:18:10:00 temp ping -s 408 192.168.0.125

AXIS Q6032-E Installation Guide Page 13
ENGLISH
Electrical Specifications
Unit Function Description
AXIS Q6032-E Power over Ethernet 50-57VDC, max 1.2A, Class 4
Unit Function Description
AXIS T8124 Input Voltage 100-240VAC (50-60 Hz)
Input Current 1.2A (max)
Available Output Power 60W (max)
Nominal Output Voltage 54-57VDC

Page 14 AXIS Q6032-E Installation Guide
Resetting to the Factory Default Settings
This will reset all parameters, including the IP address, to the Factory Default settings:
1. Remove the dome cover from the camera unit, this will automatically disconnect power from
the camera.
2. Press and hold the Control button and the Power button, see illustration on page 4.
3. Keep the both buttons pressed until the Status indicator LED flashes amber (this may take up to
15 seconds).
4. Release the Control button. When the Status indicator LED displays green (which can take up to
1 minute) the process is complete and the camera has been reset.
Note:
The Status indicator LED will display green for 10 seconds only. After that it will be unlit.
Refer to the Status LED table on page 6 for more information.
5. Release the Power button and replace the dome cover, this will automatically reconnect power
to the camera.
6. Re-assign the IP address, using one of the methods described in this document.
It is also possible to reset parameters to the original factory default settings via the web interface.
For more information, please see the online help or the user’s manual.
Accessing the camera from the Internet
Once installed, your AXIS Q6032-E is accessible on your local network (LAN). To access the camera
from the Internet, network routers must be configured to allow incoming traffic, which is usually
done on a specific port.
• HTTP port (default port 80) for viewing and configuration
• RTSP port (default port 554) for viewing H.264 video streams
Please refer to the documentation for your router for further instructions. For more information on
this and other topics, visit the Axis Support Web at www.axis.com/techsup
Further information
The user’s manual is available from the Axis Web site at www.axis.com or from the Axis Network
Video Product CD supplied with this product.
Tip!
Visit www.axis.com/techsup to check if there is updated firmware available for your
AXIS Q6032-E. To see the currently installed firmware version, see Setup > About.

AXIS Q6032-E Guide d’installation Page 15
FRANÇAIS
AXIS Q6032-E Guide d’installation
Ce guide d’installation explique comment installer l’AXIS Q6032-E Caméra réseau sur votre réseau.
Pour toute autre question concernant l’utilisation du produit, reportez-vous au Manuel de
l’utilisateur, que vous trouverez sur le CD joint ou sur le site www.axis.com/techsup
Procédure d’installation
1. Vérification du contenu de l’emballage par rapport à la
liste ci-dessous.
2. Vue d’ensemble du matériel. Cf. page 16.
3. Installation du matériel. Cf. page 17.
4. Attribution d’une adresse IP. Cf. page 19.
5. Configuration du mot de passe. Cf. page 22.
Contenu de l’emballage
Article Modèles/variantes/remarques
Caméra réseau AXIS Q6032-E 50 Hz/60 Hz
Bulles du dôme • Bulle transparente non fumée
• Bulle transparente fumée
Injecteur de puissance High PoE AXIS T8124 câble d’alimentation fourni (différent selon les pays)
Connecteur RJ45 Connecteur réseau norme IP66
Pare-soleil Bulle de protection en plastique, vis fournies
Étiquettes 2 étiquettes autocollantes avec le numéro de série
CD CD de la caméra vidéo sur IP Axis comprenant la documentation,
les outils d’installation et les autres logiciels
Documentation Guide d’installation de l’AXIS Q6032-E (le présent document)
Document de garantie d’Axis
Accessoires en option Consultez le site à l’adresse www.axis.com pour plus d’informations sur les
supports de fixation disponibles
Important !
Ce produit doit être utilisé
conformément aux lois et
dispositions locales en vigueur.

Page 16 AXIS Q6032-E Guide d’installation
Description du matériel
Référence et numéro de série.
Le numéro de série peut être
demandé pendant l’installation.
Voyant d’état
Bouton de
commande
Supports
Connecteur réseau (PoE)
Crochet pour
fil de sécurité
Pare-soleil
Caméra dôme
Logement de
Bouton marche/arrêt
(pour les valeurs d’usine
Bulle du dôme
Joint
en caoutchouc Anneau
métallique
Anneau du dôme
Trous pour les supports de rack
Trous de vis
Vis (4)
Attention !
Radiateur
peut être très chaud
carte mémoire SD
par défaut uniquement)
de rack (3)

AXIS Q6032-E Guide d’installation Page 17
FRANÇAIS
Installation du matériel
Avant l’installation
AXIS Q6032-E est fourni avec un pare-soleil en option et une bulle du dôme transparente et fumée.
Si nécessaire, procédez comme suit pour fixer le pare-soleil et remplacer la bulle du dôme.
Fixation du pare-soleil (facultatif)
1. Glissez le pare-soleil sur les supports de rack de la caméra dôme.
2. Fixez le pare-soleil à l’aide des vis fournies (Torx T20).
Remplacement la bulle du dôme fumée/non fumée (facultatif)
1. Retirez les 4 vis (voir illustration à la page 16).
2. Retirez l’anneau métallique et l´anneau du dome de la bulle en plastique.
3. Retirez le joint en caoutchouc et fixez-le sur la bulle du dôme choisie. Assurez-vous de bien
fixer le joint de manière à ce qu’il s’emboîte parfaitement avec la bulle du dôme.
4. Fixez l’anneau métallique et l’anneau du dôme en serrant les 4 vis au maximum.
Remarque :
Veillez à ne pas rayer ou endommager la bulle du dôme. Utilisez un chiffon doux pour
nettoyer la bulle du dôme avant de le fixer à la caméra.
Installation de AXIS Q6032-E
Important !
Le design norme IP66 de la caméra nécessite l’utilisation des connecteurs RJ45 ou RJ45
compatible norme IP66 fournis.
1. Installez les accessoires de fixation sélectionnés conformément aux instructions et retirez la
protection du connecteur réseau de la caméra.
2. Acheminez le câble réseau et fixez le connecteur
RJ45 fourni. Reportez-vous aux instructions
fournies avec le connecteur pour plus
d’informations sur le câblage et le montage.
3. Accrochez la caméra dôme au fil de sécurité du
support.
4. Connectez le câble réseau et le connecteur RJ45 au
connecteur réseau de la caméra dôme.
5. Glissez les supports de rack de la caméra dôme
dans les logements du support et tournez la
caméra.
6. Fixez la caméra dôme au support de fixation à
l’aide des 3 vis (Torx T30).
Support mural (exemple de fixation)
Fil de
sécurité Logements
Torx T30
Vis
de rack
pour supports

Page 18 AXIS Q6032-E Guide d’installation
Installation de l’injecteur AXIS T8124
L’injecteur de puissance High PoE Axis permet aux produits vidéo Axis consommant une quantité
importante d’énergie de recevoir des données et de l’alimentation via le même câble Ethernet.
Procédez comme suit pour connecter l’AXIS T8124 et l’AXIS Q6032-E.
Remarque :
Notez que Axis peut garantir l’intégralité des fonctions pour le modèle AXIS T8124
uniquement, tout autre périphérique High PoE n’est pas pris en charge.
1. Branchez l’AXIS T8124 (Données d’entrée) au commutateur réseau via un câble réseau standard.
2. Branchez l’AXIS T8124 (Données et alimentation de sortie) à l’AXIS Q6032-E, via un câble
réseau déjà branché à la caméra (voir ci-dessus).
3. Branchez l’AXIS T8124 sur une prise CA (100-240 V CA), à l’aide du câble d’alimentation fourni.
Indicateurs AXIS T8124
Voyant d’état de l’AXIS Q6032-E
DEL Couleur Indication
Port Éteint Aucune caméra connectée
Orange Alimentation insuffisante pour la caméra et le radiateur. Vérifiez le câble
Clignotement Surcharge de l’alimentation
Vert Caméra connectée, fonctionnement normal
Entrée AC Vert continu Alimentation CA connectée
Couleur Indication
Éteint Connexion stable/fonctionnement normal
Orange Continu pour le démarrage du système. Clignote pendant les mises à niveau du microprogramme
ou le rétablissement des valeurs par défaut configurées en usine.
Orange/rouge Pas de connexion au réseau.
Rouge Échec de la mise à jour du micrologiciel
Vert Continu pendant 10 s après avoir redémarré avec succès
Ethernet
Données et
Données d’entrée
Indicateur
du port
Indicateur
d’entrée CA
alimentation
AXIS Q6032-E
de connexion
de connexion
AXIS T8124
de sortie

AXIS Q6032-E Guide d’installation Page 19
FRANÇAIS
Attribution d’une adresse IP
La plupart des réseaux sont équipés d’un serveur DHCP qui attribue automatiquement des adresses
IP aux périphériques connectés. Si votre réseau en est dépourvu, votre AXIS Q6032-E utilisera
192.168.0.90 comme adresse IP par défaut.
Si vous souhaitez paramétrer une adresse IP statique, sous Windows nous recommandons
l’utilisation de l’application AXIS IP Utility ou de l’application AXIS Camera Management. Selon le
nombre de caméras à installer, choisissez la méthode qui vous convient le mieux.
Ces deux applications gratuites sont disponibles sur le CD de la caméra vidéo sur IP Axis fourni avec
ce produit. Vous pouvez également les télécharger à partir du site www.axis.com/techsup.
Remarques :
• En cas d’échec de l’attribution d’adresse IP, vérifiez qu’aucun pare-feu ne bloque l’opération.
• Pour connaître les autres méthodes d’attribution ou de détection de l’adresse IP de votre AXIS
Q6032-E, par exemple sous d’autres systèmes d’exploitation, reportez-vous à la page 24.
Méthode Recommandée pour Système d’exploitation
AXIS IP Utility (version 2)
Voir page 20
Une seule caméra
Petites installations
Windows Vista
Windows Server 2003
Windows XP
Windows 2000
Windows NT 4.0
AXIS Camera Management
Voir page 21
Plusieurs caméras
Grandes installations
Installation sur un autre sous-
réseau
Windows Vista
Windows Server 2003
Windows XP Pro
Windows 2000

Page 20 AXIS Q6032-E Guide d’installation
AXIS IP Utility - Une seule caméra/petite installation
AXIS IP Utility recherche et affiche automatiquement les périphériques Axis sur votre réseau. Cette
application sert également à attribuer manuellement une adresse IP statique.
Notez que l’ordinateur exécutant l’application AXIS IP Utility doit se trouver sur le même segment
de réseau (sous-réseau physique) que l’AXIS Q6032-E.
Détection automatique
1. Vérifiez que la caméra est connectée au réseau et sous tension.
2. Lancez AXIS IP Utility.
3. Lorsque l’icône de la caméra apparaît dans la fenêtre, double-cliquez dessus pour ouvrir la page
d’accueil correspondante.
4. Reportez-vous à la page 22 pour savoir comment configurer le mot de passe.
Attribution manuelle de l’adresse IP (facultatif)
1. Trouvez une adresse IP non utilisée sur le même segment de réseau que celui de votre
ordinateur.
2. Sélectionnez AXIS Q6032-E dans la liste.
3. Cliquez sur le bouton Assign new IP address to the selected device (Attribuer une
nouvelle adresse IP au périphérique sélectionné) et saisissez l’adresse IP.
4. Cliquez sur le bouton Assign (Attribuer) et suivez les instructions affichées à l’écran. La caméra
doit être redémarrée dans les 2 minutes pour que la nouvelle adresse IP soit prise en compte.
5. Cliquez sur le bouton Home Page (Page d’accueil) pour accéder aux pages Web de la caméra.
6. Reportez-vous à la page 22 pour savoir comment configurer le mot de passe.