Axor Montreux 16510XX1 Installation guide

Axor Montreux
16510XX1
Axor Montreux
16803XX1
Axor Montreux
16511XX1
Axor Montreux
16805XX1
Installation Instructions / Warranty

2
Installation Considerations
For best results, Hansgrohe recom-
mends that this unit be installed by a
licensed, professional plumber.
Please read over these instructions
thoroughly before beginning installa-
tion. Make sure that you have all tools
and supplies needed to complete the
installation.
•
•
Technical Information
Recommended water pressure 14.7 - 72.5 psi
Max. water pressure 145 psi
Recommended hot water temp. 120° - 140° F*
Max. hot water temp 165°F*
Hole size in mounting surface
valves 1¼"
drain pull rod 1¼"
(16510 / 16511 only)
Max. mounting surface depth
16803 / 16805 2⅜"
16510 / 16511 1⅝"
Flow rate 1.5 gpm
*Please know and follow all applicable local plumbing codes when
setting the temperature on the water heater.
16510XX1
16510XX1 / 16511XX1
16511XX1

3
16803XX1
16803XX1 / 16805XX1
16805XX1

4
Installation
16510 / 16511 only
Position the pull rod assembly in the center hole of the
mounting surface.
Install the friction washer, metal washer and mounting
nut.
Tighten the mounting nut by hand.
Tighten the tensioning screws.
All models
Position the faucet body on the mounting surface.

5
Install the friction washers, metal washers and mounting
nuts.
Tighten the mounting nuts by hand.
Tighten the tensioning screws.
Install the spout, slide bushing and o-ring.
Make sure that the slide bushing is oriented correctly.
Tighten the spout screw.
16805 / 16511 only:
Inspect the alignment of the handles.

6
If it is not satisfactory, remove the handle screw
using a 3 mm Allen wrench.
Remove the handle.
OR
Remove the handle and adapter.

7
All models:
Lightly coat the handle o-rings with the enclosed
lubricant.
Install the index caps on the hot and cold handles
and pull rod assembly.
16510/16511 only
Install the pop-up drain.
All models:
Connect the supply lines to the stops.
Use two wrenches, as shown in the
diagram, to keep the supply hoses
from twisting.
Turn on the water and check all connections for
leaks.
Reposition the handle.
Install the handle screw.
Caution: the hot water
riser may be hot!

8
Install the pop-up drain (16510 / 16511 only)
Attach the swivel connector to the end of the
horizontal rod.
Attach the swivel connector to the end of the
pull rod. Position as desired and tighten with a
small, flat bladed screwdriver.
Remove the plunger assembly.
Unscrew the drain outlet flange from the tee.
Unscrew the tailpiece from the tee. Wrap the
threads with Teflon tape and replace.
Install the white, flexible sealing gasket to the
flange. Place it in the sink outlet.
Install the black mack gasket, white friction ring
and retainer nut on the flange.
Do not tighten the nut against the bottom of the
sink at this time.
Thread the tee and tailpiece to the flange. The
pivot must face the faucet. Turn the drain assem-
bly if necessary.
Tighten the retainer nut.
Place the plunger assembly in the drain.
Install the horizontal rod so that the end goes
through the loop in the bottom of the plunger.
Install and hand tighten the pivot ball nut.

9
Replacement Parts
1 cross handle 16597XX0
2 screw cover (set) 97987000
3 sleeve 97993XX0
4 aerator 95378XX0
5 spout, lavatory 97990XX0
6 hot cartridge – cross handle 94009000
hot cartridge – lever handle 96350001
7 fixation set 96078000
8 pull rod 94076000
9 diverter knob 98619XX0
10 flange 98620XX0
11 spout, kitchen 98616XX0
12 cold cartridge – cross handle 94008000
cold cartridge – lever handle 96351001
13 lever handle 16691XX0
14 supply hose 14099001
XX = Color
00 = Chrome
82 = Brushed Nickel
83 = Polished Nickel
16803 / 16805
5
1
3
6
2
2
4
10
9
8
7
12
14
2
13
11
4
11x2

10
Limited Lifetime Consumer Warranty
This product has been manufactured and tested to the highest quality standards by Hansgrohe, Inc. (“Hansgrohe”). This
warranty is limited to Hansgrohe products which are purchased by a consumer in the United States after March 1, 1996, and
installed in either the United States or Canada.
WHO IS COVERED BY THE WARRANTY
This warranty extends to the original consumer purchaser only. This warranty is non-transferable.
WHAT IS COVERED BY THE WARRANTY
This warranty covers only your Hansgrohe manufactured product. Hansgrohe warrants this product against defects in material
or workmanship as follows: Hansgrohe will repair at no charge for parts only or, at its option, replace any product or part of
the product that proves defective because of improper workmanship and/or material, under normal installation, use, service
and maintenance. If Hansgrohe is unable to provide a replacement and repair is not practical or cannot be timely made,
Hansgrohe may elect to refund the purchase price in exchange for the return of the product.
LENGTH OF WARRANTY
Replacement or repaired parts of products will be covered for the term of this warranty as stated in the following two sentenc-
es. If you are a consumer who purchased the product for use primarily for personal, family, or household purposes, this war-
ranty extends for as long as you own the product and the home in which the product is originally installed. If you purchased
the product for use primarily for any other purpose, including, without limitation, a commercial purpose, this warranty extends
only (i) for 1 year, with respect to Hansgrohe and Commercial products, and (ii) for 5 years, with respect to AXOR products.
Cleaning Recommendation for Hansgrohe Products
Modern lavatory faucets, kitchen faucets, and showers consist of very different materials to comply with the needs of the
market with regard to design and functionality. To avoid damage and returns, it is necessary to consider certain criteria when
cleaning.
Cleaning Materials for Faucets and Showers
Acids are a necessary ingredient of cleaning materials for removing lime, however please pay attention to the following points
when cleaning faucets and showers:
Only use cleaning materials which are explicitly intended for this type of application.
Never use cleaning materials which contain hydrochloric, formic, phosphoric, or acetic acid, as they cause considerable
damage.
Never mix one cleaning material with another.
Never use cleaning materials or appliances with an abrasive effect, such as unsuitable cleaning powders, sponge pads,
or micro fiber cloths.
Cleaning Instructions for Faucets and Showers
Please follow the cleaning material manufacturer’s instructions. In addition, pay attention to the following points:
Clean the faucets and showers as and when required
Use the amount of cleaning product and the amount of time recommended by the manufacturer. Do not leave the cleaner
on the fixture longer than necessary.
Regular cleaning can prevent calcification.
When using spray cleaners, spray first onto a soft cloth or sponge. Never spray directly onto the faucet as droplets can
enter openings and gaps and cause damage.
After cleaning, rinse thoroughly with clean water to remove any cleaner residue.
Important
Residues of liquid soaps, shampoos, and shower foams can also cause damage, so rinse with clean water after using.
Please note: if the surface is already damaged, the effect of cleaning materials will cause further damage.
Components with damaged surfaces must be replaced or injury could result.
Damage caused by improper treatment is not covered under the warranty.
•
•
•
•
•
•
•
•
•