B.Well MED-3000 User manual
1. INTRODUCTION
Dear consumer!
We congratulate you with a B.Well infrared thermometer buying!
Thank you for choosing our product!
MED-3000 advantages include:
1. 3 in 1 thermometer
Human body/ object/ ambient temperature
2.One-second reading
3.Accurate and reliable
4.Traffic lights backlight
(Human Body Mode)
5.Tracking light
6.25-memory recall
7. Large LCD Display
8.°C/°F Switchable function
2. INTENDED PURPOSE
The device is intended for the intermittent measurement and
monitoring of human body temperature from forehead measurement
at home, clinics and hospital.
A control measurement using a conventional thermometer is
recommended in the following cases:
1. If the reading is surprisingly low.
2. For new-born infants up to 100 days old.
3. For children under three years of age who have a weakened immune
system or who react unusually in the presence or absence of fever.
3. PRECAUTIONS
When using this product, please be sure to follow all the notes listed
below. Any action against these notices may cause injury or affect the
accuracy.
1. Close supervision is necessary when the thermometer is used by, on,
or near children, handicapped persons or invalids.
2. Use the thermometer only for the intended use described in this
manual.
3. Do not use the thermometer if it is not working properly, or if it has
suffered any damage.
Cautions and Warnings
As with any thermometer, proper technique is crucial to obtaining
accurate temperature readings.
Please read this manual thoroughly and carefully before using.
Always operate the thermometer in an operating temperature
range 5°C to 40°C (41°F to 104°F), and relative humidity 15 to 93%.
Always store the thermometer in a cool and dry place -25°C to 70°C
(-13°F to 158°F) and relative humidity 15% to 93%.
The device requires no calibration.
The device contains no user serviceable parts.
The user must check that the equipment functions safely and see
that it is in proper working condition before being use.
The manufacturer does not require such preventive inspections by
other persons.
No modification of this equipment is allowed.
The device is not suitable for use in the presence of flammable
anesthetic mixtures with air or with oxygen or nitrous oxide.
Do not clean or maintenance the device is in use.
Avoid direct sunlight.
Avoid dropping the thermometer, if it happens and you think the
thermometer may be damaged, please contact customer services
immediately.
Do not touch the lens.
Do not disassemble the thermometer.
Basic safety precautions should always be observed, especially
when the thermometer is used on or near children and disabled
persons.
This thermometer is not intended to substitute for a
consultation with your physician.
Under any circumstances, the temperature taking result is ONLY
for reference. Before taking any medical action, please consult your
physician.
When the measured temperature falls within the fever temperature
range of >37.9°C (100.2°F) and <42.9°C (109.3°F), as indicated by the
red LCD on display, please consult with your physician immediately.
This thermometer and the subject must remain in a stable
environment for at least 30 minutes before measuring the
temperature.
2. It is recommended to remove the batteries if the unit will not be used
for an extended period of time.
3. The batteries should be kept away out of children’s reach. If they are
swallowed, promptly see a doctor for help.
4.Dispose of used batteries in accordance with the applicable legal
regulations. Never dispose of batteries in the normal household
waste.
9. SWITCHING BETWEEN FAHRENHEIT AND CELSIUS
This thermometer can display results in either degrees Celsius (°C) or
degrees Fahrenheit (°F).
1. Be sure the thermometer is OFF before selecting the temperature
unit.
2. Long-press the ON Button for 8 seconds until the signal °C or °F
displayed on the LCD panel as figure shown. Re-press the ON Button
to select °C or °F unit.
3. Long-press the ON Button for 3 seconds, it will automatically save
your choice and turn off.
Celsius / °C Fahrenheit / °F
10. TURNING ON THE TRACKING LIGHT
This thermometer provides Tracking Light (LED Light) to help users
placing the thermometer at the correct position.
1. Be sure the thermometer is OFF.
2. Long-press the ON Button for 10 seconds until signal displayed
on the LCD panel.
3. Short press the ON Button to turn on or off LED light – when LED is
turned on, the blue light will indicate, while it is turned off there is no
light.
4.Long-press the ON Button for 3 seconds, it will automatically save
your choice and turn off.
11. SWITCHING BETWEEN MEASURING MODES
Following modes can be selected:
1. Body Mode
This mode is used to measure the
forehead temperature.
2.Object Mode
This mode is used to measure the
object temperature.
Choose the mode you need using a slider on the side of the device.
Silent mode
Beeps may be switched off:
1. Be sure the infrared thermometer is off.
2. Hold the ON Button for about 12 seconds after “ON” shows on the
LCD panel. (Note: keep holding the button when “°C/°F” is displayed
on the LCD panel).
3. Press the ON Button again to turn ON the beep.
4.Then long-press the Button for 3 seconds, it will automatically save
your choice and turn off.
12. MEASURING HUMAN TEMPERATURE
Tips for measuring human temperature
Bear in mind that the thermometer needs to have been in the room in
which the measurement is taken for at least 30 minutes before use.
NOTE:
Attempting to take temperature readings from sites on the body
other than the forehead may produce inaccurate results.
If the patient’s skin is covered with hair, sweat, or dirt, clean the area
and wait 10 minutes before taking a measurement.
Ensure that the thermometer is held firmly during measurement and
that the patient does not move until the measurement is complete.
Movement can impact the measurement.
If the probe is placed at an angle close to the forehead measurement,
the reading will be affected by surrounding temperature.
Babies’ skin reacts very quickly to the ambient temperature.
Therefore, do not take their temperature with the MED-3000
infrared thermometer during or after breastfeeding, because the skin
temperature may then be lower than the internal body temperature.
Readings taken while asleep should not be compared directly to
readings taken while awake, as body temperature while asleep is
typically lower.
Avoid measuring temperature in 30 minutes after exercise, bathing,
or returning from outdoor.
4. CONTRAINDICATIONS
Contraindications: are not revealed.
5. PRODUCT IDENTIFICATION
Tracking Light (LED)
Measurement
Sensor
Mode Switch
Battery Cover
LCD Display
ON Button/
Measurement /
Memory/ Settup
6. DESCRIPTION OF LCD DISPLAY
Object mode Body mode
Temperature
reading
Temperature
unit
Battery
indication
Memory
indication
7. WHAT IS A “NORMAL” TEMPERATURE?
The temperature in the forehead and temple area differs from
the internal temperature, which is taken orally or rectally.
Vasoconstriction, an effect which constricts the blood vessels and
cools the skin, can occur during the early stages of a fever. In this case,
the temperature measured by the MED-3000 Infrared thermometer
may be unusually low. If the measurement therefore does not
match the patient’s own perception or is unusually low, repeat the
measurement every 15 minutes. As a reference, you can also measure
the internal body temperature using a conventional oral or rectal
thermometer. Body temperature can vary from one individual/ person
to next. It also varies by location on the body and time of day. Below
show the statistical normal ranges from different sites. Please keep
in mind that temperatures measured from different sites, even at
the same time, should not be directly compared. Fever indicates that
the body temperature is higher than normal. This symptom may be
caused by infection, overdressing or immunization. Some people
may not experience fever even when they are ill. These include, but
are not limited to, infants younger than 3 months old, persons with
compromised immune systems, persons taking antibiotics, steroids
or antipyretics (aspirin, ibuprofen, acetaminophen), or persons with
certain chronic illnesses. Please consult your physician when you feel
ill even if you do not have fever.
Normal Temperature Range of various body sites
Oral 36,4 - 37,6°C
Rectal/ Ear 36,7 - 38,2°C
Axillary 35,8 - 37,3°C
8. BATTERY INSTALLATION/ REPLACEMENT
Low battery warning:
The thermometer comes with two 1.5 V AAA alkaline batteries. The
thermometer will display “ “ to alert you when its power is
getting low. Please follow the steps below to replace new batteries
immediately.
Replacing the Battery:
1. Gently slide the battery cover back.
2. Carefully remove the old batteries and properly discard.
3. Insert new batteries (two 1.5V AAA size alkaline batteries) according
to the proper polarity.
4.Slide the battery cover back on.
NOTE:
1. Although the thermometer works when “ “ appearing, we still
recommend that you change the batteries.
Measuring Human Temperature
Taking a Measurement
1. Press ON Button to turn on the thermometer first. The unit will run
a self-test and the LCD will briefly display all of its symbols during
this time.
2. Push the Mode switch to select Body mode.
The device sounds one short beep when it is turned on and the
temperature unit (°C or °F) flashes to confirms the readiness to
perform the measurement.
3. Position the thermometer at a distance within 3 cm from the center
of the patient’s forehead. Make sure the probe is flat and close to
the forehead, not at an angle.
4.Press and release the ON Button. The measurement result will be
done in 1 second. The reading is shown together with LCD lighting
and one long beep informs about the temperature measurement,
and after a while another, short, confirming the saving of the result
to the memory and readiness for the next measurement.
~3 cm
5.If the reading is ≤37,4°C, the display will stay green.
If the reading is ≥37,5°C - ≤37,9°C (≥99,5°F - ≤100,2°F), the display will
turn yellow.
If the reading is >37,9°C (100,2°F), the display will show together
with red LCD and six short beeps.
6.Press the ON Button to turn off the unit, or leave it idle for 10
seconds, the unit will switch off automatically.
13. MEASURING OBJECT/ LIQUID TEMPERATURE
Taking a Measurement
1. Press ON Button to turn on the thermometer first. The unit will run
a self-test and the LCD will briefly display all of its symbols during
this time.
2. Push the Mode switch to select Object mode.
The device sounds two short beeps indicating that the object mode
is turned on and the temperature unit flashes.
3. Position the thermometer at a distance within 3 cm from the object.
Make sure the probe is flat and close to the object, not at an angle.
4.Press and release the ON Button. The measurement result will be
done in 1 second. The reading is shown together with LCD lighting
and one long beep informs about the temperature measurement,
and after a while another, short, confirming the saving of the result
to the memory and readiness for the next measurement.
5.Press the ON Button to turn off the unit, or leave it idle for 10
seconds, the unit will switch off automatically.
14. MEMORY FUNCTION
Memory Recall
You can recall up to 25 measurements currently stored in memory to
share with your physician or trained healthcare professional.
1. Be sure the thermometer is OFF before recalling the memory. Press
for 2 seconds the ON Button to enter the memory mode.
2. Each time you press the Button, a result will be displayed in the
order of dates (latest result shown first), together with “MEM” and
number (from 1 to 25).
3. The symbol or symbol will appear with each measurement
stored in memory to indicate whether a body or object temperature
was taken. Body Mode measurements: LCD backlight will turn green,
yellow or red according to the memory reading.
4.Exit the memory. Long press ON Button to exit the memory or keep
the thermometer in idle for 10 seconds to switch off automatically.
Instructions for use
MED-3000
Infrared thermometer
EN
1. INTRODUCTION
Dear consumer!
We congratulate you with a B.Well infrared thermometer buying!
Thank you for choosing our product!
MED-3000 advantages include:
1. 3 in 1 thermometer
Human body/ object/ ambient temperature
2.One-second reading
3.Accurate and reliable
4.Traffic lights backlight
(Human Body Mode)
5.Tracking light
6.25-memory recall
7. Large LCD Display
8.°C/°F Switchable function
2. INTENDED PURPOSE
The device is intended for the intermittent measurement and
monitoring of human body temperature from forehead measurement
at home, clinics and hospital.
A control measurement using a conventional thermometer is
recommended in the following cases:
1. If the reading is surprisingly low.
2. For new-born infants up to 100 days old.
3. For children under three years of age who have a weakened immune
system or who react unusually in the presence or absence of fever.
3. PRECAUTIONS
When using this product, please be sure to follow all the notes listed
below. Any action against these notices may cause injury or affect the
accuracy.
1. Close supervision is necessary when the thermometer is used by, on,
or near children, handicapped persons or invalids.
2. Use the thermometer only for the intended use described in this
manual.
3. Do not use the thermometer if it is not working properly, or if it has
suffered any damage.
Cautions and Warnings
As with any thermometer, proper technique is crucial to obtaining
accurate temperature readings.
Please read this manual thoroughly and carefully before using.
Always operate the thermometer in an operating temperature
range 5°C to 40°C (41°F to 104°F), and relative humidity 15 to 93%.
Always store the thermometer in a cool and dry place -25°C to 70°C
(-13°F to 158°F) and relative humidity 15% to 93%.
The device requires no calibration.
The device contains no user serviceable parts.
The user must check that the equipment functions safely and see
that it is in proper working condition before being use.
The manufacturer does not require such preventive inspections by
other persons.
No modification of this equipment is allowed.
The device is not suitable for use in the presence of flammable
anesthetic mixtures with air or with oxygen or nitrous oxide.
Do not clean or maintenance the device is in use.
Avoid direct sunlight.
Avoid dropping the thermometer, if it happens and you think the
thermometer may be damaged, please contact customer services
immediately.
Do not touch the lens.
Do not disassemble the thermometer.
Basic safety precautions should always be observed, especially
when the thermometer is used on or near children and disabled
persons.
This thermometer is not intended to substitute for a
consultation with your physician.
Under any circumstances, the temperature taking result is ONLY
for reference. Before taking any medical action, please consult your
physician.
When the measured temperature falls within the fever temperature
range of >37.9°C (100.2°F) and <42.9°C (109.3°F), as indicated by the
red LCD on display, please consult with your physician immediately.
This thermometer and the subject must remain in a stable
environment for at least 30 minutes before measuring the
temperature.
2. It is recommended to remove the batteries if the unit will not be used
for an extended period of time.
3. The batteries should be kept away out of children’s reach. If they are
swallowed, promptly see a doctor for help.
4.Dispose of used batteries in accordance with the applicable legal
regulations. Never dispose of batteries in the normal household
waste.
9. SWITCHING BETWEEN FAHRENHEIT AND CELSIUS
This thermometer can display results in either degrees Celsius (°C) or
degrees Fahrenheit (°F).
1. Be sure the thermometer is OFF before selecting the temperature
unit.
2. Long-press the ON Button for 8 seconds until the signal °C or °F
displayed on the LCD panel as figure shown. Re-press the ON Button
to select °C or °F unit.
3. Long-press the ON Button for 3 seconds, it will automatically save
your choice and turn off.
Celsius / °C Fahrenheit / °F
10. TURNING ON THE TRACKING LIGHT
This thermometer provides Tracking Light (LED Light) to help users
placing the thermometer at the correct position.
1. Be sure the thermometer is OFF.
2. Long-press the ON Button for 10 seconds until signal displayed
on the LCD panel.
3. Short press the ON Button to turn on or off LED light – when LED is
turned on, the blue light will indicate, while it is turned off there is no
light.
4.Long-press the ON Button for 3 seconds, it will automatically save
your choice and turn off.
11. SWITCHING BETWEEN MEASURING MODES
Following modes can be selected:
1. Body Mode
This mode is used to measure the
forehead temperature.
2.Object Mode
This mode is used to measure the
object temperature.
Choose the mode you need using a slider on the side of the device.
Silent mode
Beeps may be switched off:
1. Be sure the infrared thermometer is off.
2. Hold the ON Button for about 12 seconds after “ON” shows on the
LCD panel. (Note: keep holding the button when “°C/°F” is displayed
on the LCD panel).
3. Press the ON Button again to turn ON the beep.
4.Then long-press the Button for 3 seconds, it will automatically save
your choice and turn off.
12. MEASURING HUMAN TEMPERATURE
Tips for measuring human temperature
Bear in mind that the thermometer needs to have been in the room in
which the measurement is taken for at least 30 minutes before use.
NOTE:
Attempting to take temperature readings from sites on the body
other than the forehead may produce inaccurate results.
If the patient’s skin is covered with hair, sweat, or dirt, clean the area
and wait 10 minutes before taking a measurement.
Ensure that the thermometer is held firmly during measurement and
that the patient does not move until the measurement is complete.
Movement can impact the measurement.
If the probe is placed at an angle close to the forehead measurement,
the reading will be affected by surrounding temperature.
Babies’ skin reacts very quickly to the ambient temperature.
Therefore, do not take their temperature with the MED-3000
infrared thermometer during or after breastfeeding, because the skin
temperature may then be lower than the internal body temperature.
Readings taken while asleep should not be compared directly to
readings taken while awake, as body temperature while asleep is
typically lower.
Avoid measuring temperature in 30 minutes after exercise, bathing,
or returning from outdoor.
4. CONTRAINDICATIONS
Contraindications: are not revealed.
5. PRODUCT IDENTIFICATION
Tracking Light (LED)
Measurement
Sensor
Mode Switch
Battery Cover
LCD Display
ON Button/
Measurement /
Memory/ Settup
6. DESCRIPTION OF LCD DISPLAY
Object mode Body mode
Temperature
reading
Temperature
unit
Battery
indication
Memory
indication
7. WHAT IS A “NORMAL” TEMPERATURE?
The temperature in the forehead and temple area differs from
the internal temperature, which is taken orally or rectally.
Vasoconstriction, an effect which constricts the blood vessels and
cools the skin, can occur during the early stages of a fever. In this case,
the temperature measured by the MED-3000 Infrared thermometer
may be unusually low. If the measurement therefore does not
match the patient’s own perception or is unusually low, repeat the
measurement every 15 minutes. As a reference, you can also measure
the internal body temperature using a conventional oral or rectal
thermometer. Body temperature can vary from one individual/ person
to next. It also varies by location on the body and time of day. Below
show the statistical normal ranges from different sites. Please keep
in mind that temperatures measured from different sites, even at
the same time, should not be directly compared. Fever indicates that
the body temperature is higher than normal. This symptom may be
caused by infection, overdressing or immunization. Some people
may not experience fever even when they are ill. These include, but
are not limited to, infants younger than 3 months old, persons with
compromised immune systems, persons taking antibiotics, steroids
or antipyretics (aspirin, ibuprofen, acetaminophen), or persons with
certain chronic illnesses. Please consult your physician when you feel
ill even if you do not have fever.
Normal Temperature Range of various body sites
Oral 36,4 - 37,6°C
Rectal/ Ear 36,7 - 38,2°C
Axillary 35,8 - 37,3°C
8. BATTERY INSTALLATION/ REPLACEMENT
Low battery warning:
The thermometer comes with two 1.5 V AAA alkaline batteries. The
thermometer will display “ “ to alert you when its power is
getting low. Please follow the steps below to replace new batteries
immediately.
Replacing the Battery:
1. Gently slide the battery cover back.
2. Carefully remove the old batteries and properly discard.
3. Insert new batteries (two 1.5V AAA size alkaline batteries) according
to the proper polarity.
4.Slide the battery cover back on.
NOTE:
1. Although the thermometer works when “ “ appearing, we still
recommend that you change the batteries.
Measuring Human Temperature
Taking a Measurement
1. Press ON Button to turn on the thermometer first. The unit will run
a self-test and the LCD will briefly display all of its symbols during
this time.
2. Push the Mode switch to select Body mode.
The device sounds one short beep when it is turned on and the
temperature unit (°C or °F) flashes to confirms the readiness to
perform the measurement.
3. Position the thermometer at a distance within 3 cm from the center
of the patient’s forehead. Make sure the probe is flat and close to
the forehead, not at an angle.
4.Press and release the ON Button. The measurement result will be
done in 1 second. The reading is shown together with LCD lighting
and one long beep informs about the temperature measurement,
and after a while another, short, confirming the saving of the result
to the memory and readiness for the next measurement.
~3 cm
5.If the reading is ≤37,4°C, the display will stay green.
If the reading is ≥37,5°C - ≤37,9°C (≥99,5°F - ≤100,2°F), the display will
turn yellow.
If the reading is >37,9°C (100,2°F), the display will show together
with red LCD and six short beeps.
6.Press the ON Button to turn off the unit, or leave it idle for 10
seconds, the unit will switch off automatically.
13. MEASURING OBJECT/ LIQUID TEMPERATURE
Taking a Measurement
1. Press ON Button to turn on the thermometer first. The unit will run
a self-test and the LCD will briefly display all of its symbols during
this time.
2. Push the Mode switch to select Object mode.
The device sounds two short beeps indicating that the object mode
is turned on and the temperature unit flashes.
3. Position the thermometer at a distance within 3 cm from the object.
Make sure the probe is flat and close to the object, not at an angle.
4.Press and release the ON Button. The measurement result will be
done in 1 second. The reading is shown together with LCD lighting
and one long beep informs about the temperature measurement,
and after a while another, short, confirming the saving of the result
to the memory and readiness for the next measurement.
5.Press the ON Button to turn off the unit, or leave it idle for 10
seconds, the unit will switch off automatically.
14. MEMORY FUNCTION
Memory Recall
You can recall up to 25 measurements currently stored in memory to
share with your physician or trained healthcare professional.
1. Be sure the thermometer is OFF before recalling the memory. Press
for 2 seconds the ON Button to enter the memory mode.
2. Each time you press the Button, a result will be displayed in the
order of dates (latest result shown first), together with “MEM” and
number (from 1 to 25).
3. The symbol or symbol will appear with each measurement
stored in memory to indicate whether a body or object temperature
was taken. Body Mode measurements: LCD backlight will turn green,
yellow or red according to the memory reading.
4.Exit the memory. Long press ON Button to exit the memory or keep
the thermometer in idle for 10 seconds to switch off automatically.
Instructions for use
MED-3000
Infrared thermometer
EN
1. INTRODUCTION
Dear consumer!
We congratulate you with a B.Well infrared thermometer buying!
Thank you for choosing our product!
MED-3000 advantages include:
1. 3 in 1 thermometer
Human body/ object/ ambient temperature
2.One-second reading
3.Accurate and reliable
4.Traffic lights backlight
(Human Body Mode)
5.Tracking light
6.25-memory recall
7. Large LCD Display
8.°C/°F Switchable function
2. INTENDED PURPOSE
The device is intended for the intermittent measurement and
monitoring of human body temperature from forehead measurement
at home, clinics and hospital.
A control measurement using a conventional thermometer is
recommended in the following cases:
1. If the reading is surprisingly low.
2. For new-born infants up to 100 days old.
3. For children under three years of age who have a weakened immune
system or who react unusually in the presence or absence of fever.
3. PRECAUTIONS
When using this product, please be sure to follow all the notes listed
below. Any action against these notices may cause injury or affect the
accuracy.
1. Close supervision is necessary when the thermometer is used by, on,
or near children, handicapped persons or invalids.
2. Use the thermometer only for the intended use described in this
manual.
3. Do not use the thermometer if it is not working properly, or if it has
suffered any damage.
Cautions and Warnings
As with any thermometer, proper technique is crucial to obtaining
accurate temperature readings.
Please read this manual thoroughly and carefully before using.
Always operate the thermometer in an operating temperature
range 5°C to 40°C (41°F to 104°F), and relative humidity 15 to 93%.
Always store the thermometer in a cool and dry place -25°C to 70°C
(-13°F to 158°F) and relative humidity 15% to 93%.
The device requires no calibration.
The device contains no user serviceable parts.
The user must check that the equipment functions safely and see
that it is in proper working condition before being use.
The manufacturer does not require such preventive inspections by
other persons.
No modification of this equipment is allowed.
The device is not suitable for use in the presence of flammable
anesthetic mixtures with air or with oxygen or nitrous oxide.
Do not clean or maintenance the device is in use.
Avoid direct sunlight.
Avoid dropping the thermometer, if it happens and you think the
thermometer may be damaged, please contact customer services
immediately.
Do not touch the lens.
Do not disassemble the thermometer.
Basic safety precautions should always be observed, especially
when the thermometer is used on or near children and disabled
persons.
This thermometer is not intended to substitute for a
consultation with your physician.
Under any circumstances, the temperature taking result is ONLY
for reference. Before taking any medical action, please consult your
physician.
When the measured temperature falls within the fever temperature
range of >37.9°C (100.2°F) and <42.9°C (109.3°F), as indicated by the
red LCD on display, please consult with your physician immediately.
This thermometer and the subject must remain in a stable
environment for at least 30 minutes before measuring the
temperature.
2. It is recommended to remove the batteries if the unit will not be used
for an extended period of time.
3. The batteries should be kept away out of children’s reach. If they are
swallowed, promptly see a doctor for help.
4.Dispose of used batteries in accordance with the applicable legal
regulations. Never dispose of batteries in the normal household
waste.
9. SWITCHING BETWEEN FAHRENHEIT AND CELSIUS
This thermometer can display results in either degrees Celsius (°C) or
degrees Fahrenheit (°F).
1. Be sure the thermometer is OFF before selecting the temperature
unit.
2. Long-press the ON Button for 8 seconds until the signal °C or °F
displayed on the LCD panel as figure shown. Re-press the ON Button
to select °C or °F unit.
3. Long-press the ON Button for 3 seconds, it will automatically save
your choice and turn off.
Celsius / °C Fahrenheit / °F
10. TURNING ON THE TRACKING LIGHT
This thermometer provides Tracking Light (LED Light) to help users
placing the thermometer at the correct position.
1. Be sure the thermometer is OFF.
2. Long-press the ON Button for 10 seconds until signal displayed
on the LCD panel.
3. Short press the ON Button to turn on or off LED light – when LED is
turned on, the blue light will indicate, while it is turned off there is no
light.
4.Long-press the ON Button for 3 seconds, it will automatically save
your choice and turn off.
11. SWITCHING BETWEEN MEASURING MODES
Following modes can be selected:
1. Body Mode
This mode is used to measure the
forehead temperature.
2.Object Mode
This mode is used to measure the
object temperature.
Choose the mode you need using a slider on the side of the device.
Silent mode
Beeps may be switched off:
1. Be sure the infrared thermometer is off.
2. Hold the ON Button for about 12 seconds after “ON” shows on the
LCD panel. (Note: keep holding the button when “°C/°F” is displayed
on the LCD panel).
3. Press the ON Button again to turn ON the beep.
4.Then long-press the Button for 3 seconds, it will automatically save
your choice and turn off.
12. MEASURING HUMAN TEMPERATURE
Tips for measuring human temperature
Bear in mind that the thermometer needs to have been in the room in
which the measurement is taken for at least 30 minutes before use.
NOTE:
Attempting to take temperature readings from sites on the body
other than the forehead may produce inaccurate results.
If the patient’s skin is covered with hair, sweat, or dirt, clean the area
and wait 10 minutes before taking a measurement.
Ensure that the thermometer is held firmly during measurement and
that the patient does not move until the measurement is complete.
Movement can impact the measurement.
If the probe is placed at an angle close to the forehead measurement,
the reading will be affected by surrounding temperature.
Babies’ skin reacts very quickly to the ambient temperature.
Therefore, do not take their temperature with the MED-3000
infrared thermometer during or after breastfeeding, because the skin
temperature may then be lower than the internal body temperature.
Readings taken while asleep should not be compared directly to
readings taken while awake, as body temperature while asleep is
typically lower.
Avoid measuring temperature in 30 minutes after exercise, bathing,
or returning from outdoor.
4. CONTRAINDICATIONS
Contraindications: are not revealed.
5. PRODUCT IDENTIFICATION
Tracking Light (LED)
Measurement
Sensor
Mode Switch
Battery Cover
LCD Display
ON Button/
Measurement /
Memory/ Settup
6. DESCRIPTION OF LCD DISPLAY
Object mode Body mode
Temperature
reading
Temperature
unit
Battery
indication
Memory
indication
7. WHAT IS A “NORMAL” TEMPERATURE?
The temperature in the forehead and temple area differs from
the internal temperature, which is taken orally or rectally.
Vasoconstriction, an effect which constricts the blood vessels and
cools the skin, can occur during the early stages of a fever. In this case,
the temperature measured by the MED-3000 Infrared thermometer
may be unusually low. If the measurement therefore does not
match the patient’s own perception or is unusually low, repeat the
measurement every 15 minutes. As a reference, you can also measure
the internal body temperature using a conventional oral or rectal
thermometer. Body temperature can vary from one individual/ person
to next. It also varies by location on the body and time of day. Below
show the statistical normal ranges from different sites. Please keep
in mind that temperatures measured from different sites, even at
the same time, should not be directly compared. Fever indicates that
the body temperature is higher than normal. This symptom may be
caused by infection, overdressing or immunization. Some people
may not experience fever even when they are ill. These include, but
are not limited to, infants younger than 3 months old, persons with
compromised immune systems, persons taking antibiotics, steroids
or antipyretics (aspirin, ibuprofen, acetaminophen), or persons with
certain chronic illnesses. Please consult your physician when you feel
ill even if you do not have fever.
Normal Temperature Range of various body sites
Oral 36,4 - 37,6°C
Rectal/ Ear 36,7 - 38,2°C
Axillary 35,8 - 37,3°C
8. BATTERY INSTALLATION/ REPLACEMENT
Low battery warning:
The thermometer comes with two 1.5 V AAA alkaline batteries. The
thermometer will display “ “ to alert you when its power is
getting low. Please follow the steps below to replace new batteries
immediately.
Replacing the Battery:
1. Gently slide the battery cover back.
2. Carefully remove the old batteries and properly discard.
3. Insert new batteries (two 1.5V AAA size alkaline batteries) according
to the proper polarity.
4.Slide the battery cover back on.
NOTE:
1. Although the thermometer works when “ “ appearing, we still
recommend that you change the batteries.
Measuring Human Temperature
Taking a Measurement
1. Press ON Button to turn on the thermometer first. The unit will run
a self-test and the LCD will briefly display all of its symbols during
this time.
2. Push the Mode switch to select Body mode.
The device sounds one short beep when it is turned on and the
temperature unit (°C or °F) flashes to confirms the readiness to
perform the measurement.
3. Position the thermometer at a distance within 3 cm from the center
of the patient’s forehead. Make sure the probe is flat and close to
the forehead, not at an angle.
4.Press and release the ON Button. The measurement result will be
done in 1 second. The reading is shown together with LCD lighting
and one long beep informs about the temperature measurement,
and after a while another, short, confirming the saving of the result
to the memory and readiness for the next measurement.
~3 cm
5.If the reading is ≤37,4°C, the display will stay green.
If the reading is ≥37,5°C - ≤37,9°C (≥99,5°F - ≤100,2°F), the display will
turn yellow.
If the reading is >37,9°C (100,2°F), the display will show together
with red LCD and six short beeps.
6.Press the ON Button to turn off the unit, or leave it idle for 10
seconds, the unit will switch off automatically.
13. MEASURING OBJECT/ LIQUID TEMPERATURE
Taking a Measurement
1. Press ON Button to turn on the thermometer first. The unit will run
a self-test and the LCD will briefly display all of its symbols during
this time.
2. Push the Mode switch to select Object mode.
The device sounds two short beeps indicating that the object mode
is turned on and the temperature unit flashes.
3. Position the thermometer at a distance within 3 cm from the object.
Make sure the probe is flat and close to the object, not at an angle.
4.Press and release the ON Button. The measurement result will be
done in 1 second. The reading is shown together with LCD lighting
and one long beep informs about the temperature measurement,
and after a while another, short, confirming the saving of the result
to the memory and readiness for the next measurement.
5.Press the ON Button to turn off the unit, or leave it idle for 10
seconds, the unit will switch off automatically.
14. MEMORY FUNCTION
Memory Recall
You can recall up to 25 measurements currently stored in memory to
share with your physician or trained healthcare professional.
1. Be sure the thermometer is OFF before recalling the memory. Press
for 2 seconds the ON Button to enter the memory mode.
2. Each time you press the Button, a result will be displayed in the
order of dates (latest result shown first), together with “MEM” and
number (from 1 to 25).
3. The symbol or symbol will appear with each measurement
stored in memory to indicate whether a body or object temperature
was taken. Body Mode measurements: LCD backlight will turn green,
yellow or red according to the memory reading.
4.Exit the memory. Long press ON Button to exit the memory or keep
the thermometer in idle for 10 seconds to switch off automatically.
Instructions for use
MED-3000
Infrared thermometer
EN
1. INTRODUCTION
Dear consumer!
We congratulate you with a B.Well infrared thermometer buying!
Thank you for choosing our product!
MED-3000 advantages include:
1. 3 in 1 thermometer
Human body/ object/ ambient temperature
2.One-second reading
3.Accurate and reliable
4.Traffic lights backlight
(Human Body Mode)
5.Tracking light
6.25-memory recall
7. Large LCD Display
8.°C/°F Switchable function
2. INTENDED PURPOSE
The device is intended for the intermittent measurement and
monitoring of human body temperature from forehead measurement
at home, clinics and hospital.
A control measurement using a conventional thermometer is
recommended in the following cases:
1. If the reading is surprisingly low.
2. For new-born infants up to 100 days old.
3. For children under three years of age who have a weakened immune
system or who react unusually in the presence or absence of fever.
3. PRECAUTIONS
When using this product, please be sure to follow all the notes listed
below. Any action against these notices may cause injury or affect the
accuracy.
1. Close supervision is necessary when the thermometer is used by, on,
or near children, handicapped persons or invalids.
2. Use the thermometer only for the intended use described in this
manual.
3. Do not use the thermometer if it is not working properly, or if it has
suffered any damage.
Cautions and Warnings
As with any thermometer, proper technique is crucial to obtaining
accurate temperature readings.
Please read this manual thoroughly and carefully before using.
Always operate the thermometer in an operating temperature
range 5°C to 40°C (41°F to 104°F), and relative humidity 15 to 93%.
Always store the thermometer in a cool and dry place -25°C to 70°C
(-13°F to 158°F) and relative humidity 15% to 93%.
The device requires no calibration.
The device contains no user serviceable parts.
The user must check that the equipment functions safely and see
that it is in proper working condition before being use.
The manufacturer does not require such preventive inspections by
other persons.
No modification of this equipment is allowed.
The device is not suitable for use in the presence of flammable
anesthetic mixtures with air or with oxygen or nitrous oxide.
Do not clean or maintenance the device is in use.
Avoid direct sunlight.
Avoid dropping the thermometer, if it happens and you think the
thermometer may be damaged, please contact customer services
immediately.
Do not touch the lens.
Do not disassemble the thermometer.
Basic safety precautions should always be observed, especially
when the thermometer is used on or near children and disabled
persons.
This thermometer is not intended to substitute for a
consultation with your physician.
Under any circumstances, the temperature taking result is ONLY
for reference. Before taking any medical action, please consult your
physician.
When the measured temperature falls within the fever temperature
range of >37.9°C (100.2°F) and <42.9°C (109.3°F), as indicated by the
red LCD on display, please consult with your physician immediately.
This thermometer and the subject must remain in a stable
environment for at least 30 minutes before measuring the
temperature.
2. It is recommended to remove the batteries if the unit will not be used
for an extended period of time.
3. The batteries should be kept away out of children’s reach. If they are
swallowed, promptly see a doctor for help.
4.Dispose of used batteries in accordance with the applicable legal
regulations. Never dispose of batteries in the normal household
waste.
9. SWITCHING BETWEEN FAHRENHEIT AND CELSIUS
This thermometer can display results in either degrees Celsius (°C) or
degrees Fahrenheit (°F).
1. Be sure the thermometer is OFF before selecting the temperature
unit.
2. Long-press the ON Button for 8 seconds until the signal °C or °F
displayed on the LCD panel as figure shown. Re-press the ON Button
to select °C or °F unit.
3. Long-press the ON Button for 3 seconds, it will automatically save
your choice and turn off.
Celsius / °C Fahrenheit / °F
10. TURNING ON THE TRACKING LIGHT
This thermometer provides Tracking Light (LED Light) to help users
placing the thermometer at the correct position.
1. Be sure the thermometer is OFF.
2. Long-press the ON Button for 10 seconds until signal displayed
on the LCD panel.
3. Short press the ON Button to turn on or off LED light – when LED is
turned on, the blue light will indicate, while it is turned off there is no
light.
4.Long-press the ON Button for 3 seconds, it will automatically save
your choice and turn off.
11. SWITCHING BETWEEN MEASURING MODES
Following modes can be selected:
1. Body Mode
This mode is used to measure the
forehead temperature.
2.Object Mode
This mode is used to measure the
object temperature.
Choose the mode you need using a slider on the side of the device.
Silent mode
Beeps may be switched off:
1. Be sure the infrared thermometer is off.
2. Hold the ON Button for about 12 seconds after “ON” shows on the
LCD panel. (Note: keep holding the button when “°C/°F” is displayed
on the LCD panel).
3. Press the ON Button again to turn ON the beep.
4.Then long-press the Button for 3 seconds, it will automatically save
your choice and turn off.
12. MEASURING HUMAN TEMPERATURE
Tips for measuring human temperature
Bear in mind that the thermometer needs to have been in the room in
which the measurement is taken for at least 30 minutes before use.
NOTE:
Attempting to take temperature readings from sites on the body
other than the forehead may produce inaccurate results.
If the patient’s skin is covered with hair, sweat, or dirt, clean the area
and wait 10 minutes before taking a measurement.
Ensure that the thermometer is held firmly during measurement and
that the patient does not move until the measurement is complete.
Movement can impact the measurement.
If the probe is placed at an angle close to the forehead measurement,
the reading will be affected by surrounding temperature.
Babies’ skin reacts very quickly to the ambient temperature.
Therefore, do not take their temperature with the MED-3000
infrared thermometer during or after breastfeeding, because the skin
temperature may then be lower than the internal body temperature.
Readings taken while asleep should not be compared directly to
readings taken while awake, as body temperature while asleep is
typically lower.
Avoid measuring temperature in 30 minutes after exercise, bathing,
or returning from outdoor.
4. CONTRAINDICATIONS
Contraindications: are not revealed.
5. PRODUCT IDENTIFICATION
Tracking Light (LED)
Measurement
Sensor
Mode Switch
Battery Cover
LCD Display
ON Button/
Measurement /
Memory/ Settup
6. DESCRIPTION OF LCD DISPLAY
Object mode Body mode
Temperature
reading
Temperature
unit
Battery
indication
Memory
indication
7. WHAT IS A “NORMAL” TEMPERATURE?
The temperature in the forehead and temple area differs from
the internal temperature, which is taken orally or rectally.
Vasoconstriction, an effect which constricts the blood vessels and
cools the skin, can occur during the early stages of a fever. In this case,
the temperature measured by the MED-3000 Infrared thermometer
may be unusually low. If the measurement therefore does not
match the patient’s own perception or is unusually low, repeat the
measurement every 15 minutes. As a reference, you can also measure
the internal body temperature using a conventional oral or rectal
thermometer. Body temperature can vary from one individual/ person
to next. It also varies by location on the body and time of day. Below
show the statistical normal ranges from different sites. Please keep
in mind that temperatures measured from different sites, even at
the same time, should not be directly compared. Fever indicates that
the body temperature is higher than normal. This symptom may be
caused by infection, overdressing or immunization. Some people
may not experience fever even when they are ill. These include, but
are not limited to, infants younger than 3 months old, persons with
compromised immune systems, persons taking antibiotics, steroids
or antipyretics (aspirin, ibuprofen, acetaminophen), or persons with
certain chronic illnesses. Please consult your physician when you feel
ill even if you do not have fever.
Normal Temperature Range of various body sites
Oral 36,4 - 37,6°C
Rectal/ Ear 36,7 - 38,2°C
Axillary 35,8 - 37,3°C
8. BATTERY INSTALLATION/ REPLACEMENT
Low battery warning:
The thermometer comes with two 1.5 V AAA alkaline batteries. The
thermometer will display “ “ to alert you when its power is
getting low. Please follow the steps below to replace new batteries
immediately.
Replacing the Battery:
1. Gently slide the battery cover back.
2. Carefully remove the old batteries and properly discard.
3. Insert new batteries (two 1.5V AAA size alkaline batteries) according
to the proper polarity.
4.Slide the battery cover back on.
NOTE:
1. Although the thermometer works when “ “ appearing, we still
recommend that you change the batteries.
Measuring Human Temperature
Taking a Measurement
1. Press ON Button to turn on the thermometer first. The unit will run
a self-test and the LCD will briefly display all of its symbols during
this time.
2. Push the Mode switch to select Body mode.
The device sounds one short beep when it is turned on and the
temperature unit (°C or °F) flashes to confirms the readiness to
perform the measurement.
3. Position the thermometer at a distance within 3 cm from the center
of the patient’s forehead. Make sure the probe is flat and close to
the forehead, not at an angle.
4.Press and release the ON Button. The measurement result will be
done in 1 second. The reading is shown together with LCD lighting
and one long beep informs about the temperature measurement,
and after a while another, short, confirming the saving of the result
to the memory and readiness for the next measurement.
~3 cm
5.If the reading is ≤37,4°C, the display will stay green.
If the reading is ≥37,5°C - ≤37,9°C (≥99,5°F - ≤100,2°F), the display will
turn yellow.
If the reading is >37,9°C (100,2°F), the display will show together
with red LCD and six short beeps.
6.Press the ON Button to turn off the unit, or leave it idle for 10
seconds, the unit will switch off automatically.
13. MEASURING OBJECT/ LIQUID TEMPERATURE
Taking a Measurement
1. Press ON Button to turn on the thermometer first. The unit will run
a self-test and the LCD will briefly display all of its symbols during
this time.
2. Push the Mode switch to select Object mode.
The device sounds two short beeps indicating that the object mode
is turned on and the temperature unit flashes.
3. Position the thermometer at a distance within 3 cm from the object.
Make sure the probe is flat and close to the object, not at an angle.
4.Press and release the ON Button. The measurement result will be
done in 1 second. The reading is shown together with LCD lighting
and one long beep informs about the temperature measurement,
and after a while another, short, confirming the saving of the result
to the memory and readiness for the next measurement.
5.Press the ON Button to turn off the unit, or leave it idle for 10
seconds, the unit will switch off automatically.
14. MEMORY FUNCTION
Memory Recall
You can recall up to 25 measurements currently stored in memory to
share with your physician or trained healthcare professional.
1. Be sure the thermometer is OFF before recalling the memory. Press
for 2 seconds the ON Button to enter the memory mode.
2. Each time you press the Button, a result will be displayed in the
order of dates (latest result shown first), together with “MEM” and
number (from 1 to 25).
3. The symbol or symbol will appear with each measurement
stored in memory to indicate whether a body or object temperature
was taken. Body Mode measurements: LCD backlight will turn green,
yellow or red according to the memory reading.
4.Exit the memory. Long press ON Button to exit the memory or keep
the thermometer in idle for 10 seconds to switch off automatically.
Instructions for use
MED-3000
Infrared thermometer
EN
Memory Deletion
1. Remove one of the batteries, long press the ON Button.
2. Reload the battery until “ ” on the LCD screen.
Automatically on the 26th measurement: when the 25 memories have
been used up, any new measurement will be recorded and the oldest
memory deleted without you having to do anything.
NOTE:
All the readings will be cleared no matter record in Body Mode or
Object Mode.
15. CLEANING INSTRUCTIONS
For the device disinfection, 75% alcohol (available in the pharmacy)
can be used.
Measurement Sensor:
Please wipe with a clean and dry cotton swab to clean the Sensor on
the inside. Do not use water, the Sensor is not waterproof.
Thermometer:
Use a soft and dry cloth to clean the thermometer body. Do not use
abrasive cleaners. The body of the thermometer is not water-resistant.
Never put the thermometer under a running tap or submerge it into
water.
Store the thermometer in a cool and dry location. Free from dust and
away from direct sunlight. Do not expose the thermometer to extreme
temperatures, humidity, or shock.
16. TROUBLESHOOTING
FAULT OR
FAULT SYMBOL FAULT DESCRIPTION CORRECTIIVE
MEASURE
No display On
the LCD pane.
The battery has run
out. Incorrect battery
polarity.
Replace the
battery.
Please note:
The (+) side of
the battery must
face Positive (+)
indication on the
device.
Measurement
not possible (or
an abnormal
value is
displayed).
The thermometer is not
ready.
Wait until
the °C symbol is
displayed.
An abnormal
temperature
value is
displayed.
The Sensor is dirty or
damaged.
Clean the Sensor
or get it repaired.
The thermometer was
removed too early
(before the beep sound).
Wait until you
hear the beep
before removing
the thermometer
from the forehead.
or
symbol is
displayed.
The temperature
measured is outside the
measuring range.
Body Mode:
LO – temperature
<32°C (89.6°F).
HI – temperature
≥42,9°C (109.3°F)
Object Mode:
LO – temperature
<0°C (32°F).
HI – temperature
≥100°C (212°F).
Check that the
probe tip is clean
and that the
thermometer is
properly placed
on the forehead.
Symbol is
displayed. The battery has run out. Replace the
battery.
Err
Symbol is
displayed.
The ambient
temperature is
outside the operating
temperature range or is
changing too fast.
To ensure accurate
measurement, let
the thermometer
rest at operating
temperature for
30 minutes prior
to use.
22. SYMBOL INFORMATION
IP20
FOLLOW INSTRUCTIONS BEFORE USE
MANUFACTURER’S NAME
ARTICLE NUMBER
SERIAL NUMBER
TYPE BF EQUIPMENT
DISPOSAL FOR SEPARATE COLLECTION
CE MARK (0044)
OPERATING CONDITION,
TEMPERATURE 5˚C ~ 40˚C
STORAGE CONDITION,
TEPERATURE -25˚C ~ 70˚C
KEEP DRY
HOUSING INGRESS PROTECTION RATE: IP20
0044
40
5
-25
70
17. APPLIED STANDARDS
Device Standards:
Device Corresponds to the requirements of the standard for infrared
thermometers
IEC 60601-1:2012
IEC 60601-1-2:2014
ISO 80601-2-56:2009
Classification:
Anti-electric Shock Type: Internally powered equipment
Applied part: Type BF
Mode of operation: Continuous Operation
EMC: type B class I
Electromagnetic Compatibility:
Device fulfills the stipulations of the standard IEC 60601-1-2
The stipulations of EU-Directive 93/42/EEC for Medical Devices
Class Ila have been fulfilled.
18. PRODUCT SPECIFICATIONS
Measurement range:
Human Body:
Object:
32,0 ~ 42,9°C (89,6°F ~ 109,3°F)
0,0°C ~ 100°C (32,0°F ~ 211,8°F)
Accuracy:
For Body mode:
For Object mode:
±0,2°C (±0,4°F):
36,0°C ~ 39,0°C (96,8°F ~ 102,2°F)
±0,3°C (±0,5°F): out of the range
±1°C (±2°F):
0°C ~ 60,0°C (32,0°F ~ 140,0°F)
±4°C (±7,2°F): out of the range
Display resolution: 0,1°C or 0,1°F
Temperature unit: Default °C or Default °F
Operation Distance: 3 cm
Traffic lights backlight
(Body mode), Indicator
light range:
Green: <37,5°C (<99,5°F);
Yellow: ≥37,5°C - ≤37,9°C (≥99,5°F -
≤100,2°F);
Red: >37,9°C (>100,2°F)
Beeps definition: Power on and ready for working: a
short beep
Measurement finished:
1 long beep ≤37,9°C (100,2°F)
6 short beeps >37,9°C (100,2°F)
Memory: 25 mesurements
Auto shut-off: about 10 seconds after no using
Batteries: 2 x 1.5V AAA size alkaline batteries
Dimensions (L×W×H): 142,5 mm × 38 mm × 40 mm
Weight: 76g (Net: 54g)
Operating environment: Temperature:
+5°C ~ +40°C (41°F ~ 104°F);
Humidity:
15% ~ 93 % RH (non-condensing);
70Kpa-106Kpa.
Transport and Storage
environment:
Temperature:
-25°C ~ +70°C (-13°F ~ 158°F);
Humidity:
15% ~ 93% RH (non-condensing).
19. THERMOMETER SET
Thermometer set:
1. Thermometer
2. Battery 2 x 1.5V AAA size alkaline batteries
3. Soft bag
4.Instructions for use
20. UTILIZATION
The unit must be utilized in accordance with current standards
separately from domestic wastes. For utilizing it is necessary to
contact special organizations licensed to make utilization.
21. WARRANTY
Warranty period is 2 years from the date of purchase.
This warranty doesn’t cover any damages caused by improper
using, and also battery, protective cover and packaging. When a
manufacturing defect is revealed during the warranty period a faulty
unit would be repaired or, if repairing is impossible, replaced with
another one.
Manufacturing date is on the unit in a serial number: last 2 figures of
the year, then month number.
The manufacturer may change units partially or completely if
necessary, without prior notice.
ELECTROMAGNETIC COMPATIBILITY INFORMATION
Manufacturer’s Declaration of the Electromagnetic
Compatibility
Table 1
Guidance and manufacturer’s declaration –
еlectromagnetic emissions
Emissions test Compliance
RF emissions
CISPR 11 Group 1
RF emissions
CISPR 11 Class B
Harmonic emissions
IEC 61000-3-2 Not application
Voltage fluctuations/ flicker emissions
IEC 61000-3-3 Not application
Table 2
Guidance and manufacturer’s declaration –
еlectromagnetic immunity
Immunity test IEC 60601-1-2
Test level Compliance level
Electrostatic discharge
(ESD)
IEC 61000-4-2
±8 kV contact
±2 kV, ±4 kV, ±8 kV,
±15 kV air
±8 kV contact
±2 kV, ±4 kV, ±8 kV,
±15 kV air
Electrical fast transient/
burst
IEC 61000-4-4
Power supply lines: ±2 kV
input/output lines: ±1 kV Not application
Surge
IEC 61000-4-5
line(s) to line(s): ±1 kV.
line(s) to earth: ±2 kV.
100 kHz repetition
frequency
Not application
Voltage dips, short
interruptions and voltage
variations on power supply
input lines
IEC 61000-4-11
0% 0.5 cycle
At 0°, 45 °, 90 °,
135 °, 180 °, 225 °, 270 °
and 315 °
0% 1 cycle
And
70% 25/30 cycles
Single phase: at 0
0% 300 cycle
Not application
Power frequency
magnetic field
IEC 61000-4-8
30 A/m
50Hz/60Hz
30 A/m
50Hz/60Hz
Conduced RF
IEC 61000-4-6
150KHz to 80MHz:
3Vrms
6Vrms (in ISM and
amateur radio bands)
80% Am at 1kHz
Not application
Radiated RF
IEC 61000-4-3
10 V/m
80 MHz – 2,7 GHz
80 % AM at 1 kHz
10 V/m
80 MHz – 2,7 GHz
80 % AM at 1 kHz
NOTE UTis the a.c. mians voltage prior to application of the test level.
Remark In the presence of strong electromagnetic field (Horizontal/Vertical,
80MHz~180MHz and 1.4GHz~2GHz, 10V/m applied on the product), it will have
a change from 0.1°C to 0.3°C of the measured value. In case of malfunction due
to these strong electromagnetic fields, user need to wait till resume normal
operation without intervene.
IM_MED-3000_EN_5120
B.Well Swiss AG
Bahnhofstr. 24, 9443 Widnau, Switzerland
www.bwell-swiss.ch
Table 3
Guidance and manufacturer’s declaration –
electromagnetic Immunity
Radiated RF
IEC61000-4-3
(Test
specifications
for ENCLOSURE
PORT IMMUNITY
to RF wireless
communications
equipment)
Test
Frequency
(MHz)
Band
(MHz) Service
Modulation
Modulation
(W)
Distance
(m)
IMMUNITY
TEST
LEVEL
(V/m)
385 380 –
390 TETRA 400
Pulse
modulation
18 Hz
1,8 0.3 27
450 380 –
390
GMRS 460,
FRS 460
FM
± 5 kHz
deviation
1 kHz sine
2 0.3 28
710
704 –
787
LTE Band
13, 17
Pulse
modulation
217 Hz
0,2 0.3 9745
780
810
800 –
960
GSM
800/900,
TETRA 800,
iDEN 820,
CDMA 850,
LTE Band 5
Pulse
modulation
18 Hz
2 0.3 28
870
930
1720
1 700 –
1 990
GSM 1800;
CDMA
1900;
GSM 1900;
DECT;
LTE Band 1,
3, 4, 25;
UMTS
Pulse
modulation
217 Hz
2 0.3 28
1845
1970
Last revision 2020-W51
Memory Deletion
1. Remove one of the batteries, long press the ON Button.
2. Reload the battery until “ ” on the LCD screen.
Automatically on the 26th measurement: when the 25 memories have
been used up, any new measurement will be recorded and the oldest
memory deleted without you having to do anything.
NOTE:
All the readings will be cleared no matter record in Body Mode or
Object Mode.
15. CLEANING INSTRUCTIONS
For the device disinfection, 75% alcohol (available in the pharmacy)
can be used.
Measurement Sensor:
Please wipe with a clean and dry cotton swab to clean the Sensor on
the inside. Do not use water, the Sensor is not waterproof.
Thermometer:
Use a soft and dry cloth to clean the thermometer body. Do not use
abrasive cleaners. The body of the thermometer is not water-resistant.
Never put the thermometer under a running tap or submerge it into
water.
Store the thermometer in a cool and dry location. Free from dust and
away from direct sunlight. Do not expose the thermometer to extreme
temperatures, humidity, or shock.
16. TROUBLESHOOTING
FAULT OR
FAULT SYMBOL FAULT DESCRIPTION CORRECTIIVE
MEASURE
No display On
the LCD pane.
The battery has run
out. Incorrect battery
polarity.
Replace the
battery.
Please note:
The (+) side of
the battery must
face Positive (+)
indication on the
device.
Measurement
not possible (or
an abnormal
value is
displayed).
The thermometer is not
ready.
Wait until
the °C symbol is
displayed.
An abnormal
temperature
value is
displayed.
The Sensor is dirty or
damaged.
Clean the Sensor
or get it repaired.
The thermometer was
removed too early
(before the beep sound).
Wait until you
hear the beep
before removing
the thermometer
from the forehead.
or
symbol is
displayed.
The temperature
measured is outside the
measuring range.
Body Mode:
LO – temperature
<32°C (89.6°F).
HI – temperature
≥42,9°C (109.3°F)
Object Mode:
LO – temperature
<0°C (32°F).
HI – temperature
≥100°C (212°F).
Check that the
probe tip is clean
and that the
thermometer is
properly placed
on the forehead.
Symbol is
displayed. The battery has run out. Replace the
battery.
Err
Symbol is
displayed.
The ambient
temperature is
outside the operating
temperature range or is
changing too fast.
To ensure accurate
measurement, let
the thermometer
rest at operating
temperature for
30 minutes prior
to use.
22. SYMBOL INFORMATION
IP20
FOLLOW INSTRUCTIONS BEFORE USE
MANUFACTURER’S NAME
ARTICLE NUMBER
SERIAL NUMBER
TYPE BF EQUIPMENT
DISPOSAL FOR SEPARATE COLLECTION
CE MARK (0044)
OPERATING CONDITION,
TEMPERATURE 5˚C ~ 40˚C
STORAGE CONDITION,
TEPERATURE -25˚C ~ 70˚C
KEEP DRY
HOUSING INGRESS PROTECTION RATE: IP20
0044
40
5
-25
70
17. APPLIED STANDARDS
Device Standards:
Device Corresponds to the requirements of the standard for infrared
thermometers
IEC 60601-1:2012
IEC 60601-1-2:2014
ISO 80601-2-56:2009
Classification:
Anti-electric Shock Type: Internally powered equipment
Applied part: Type BF
Mode of operation: Continuous Operation
EMC: type B class I
Electromagnetic Compatibility:
Device fulfills the stipulations of the standard IEC 60601-1-2
The stipulations of EU-Directive 93/42/EEC for Medical Devices
Class Ila have been fulfilled.
18. PRODUCT SPECIFICATIONS
Measurement range:
Human Body:
Object:
32,0 ~ 42,9°C (89,6°F ~ 109,3°F)
0,0°C ~ 100°C (32,0°F ~ 211,8°F)
Accuracy:
For Body mode:
For Object mode:
±0,2°C (±0,4°F):
36,0°C ~ 39,0°C (96,8°F ~ 102,2°F)
±0,3°C (±0,5°F): out of the range
±1°C (±2°F):
0°C ~ 60,0°C (32,0°F ~ 140,0°F)
±4°C (±7,2°F): out of the range
Display resolution: 0,1°C or 0,1°F
Temperature unit: Default °C or Default °F
Operation Distance: 3 cm
Traffic lights backlight
(Body mode), Indicator
light range:
Green: <37,5°C (<99,5°F);
Yellow: ≥37,5°C - ≤37,9°C (≥99,5°F -
≤100,2°F);
Red: >37,9°C (>100,2°F)
Beeps definition: Power on and ready for working: a
short beep
Measurement finished:
1 long beep ≤37,9°C (100,2°F)
6 short beeps >37,9°C (100,2°F)
Memory: 25 mesurements
Auto shut-off: about 10 seconds after no using
Batteries: 2 x 1.5V AAA size alkaline batteries
Dimensions (L×W×H): 142,5 mm × 38 mm × 40 mm
Weight: 76g (Net: 54g)
Operating environment: Temperature:
+5°C ~ +40°C (41°F ~ 104°F);
Humidity:
15% ~ 93 % RH (non-condensing);
70Kpa-106Kpa.
Transport and Storage
environment:
Temperature:
-25°C ~ +70°C (-13°F ~ 158°F);
Humidity:
15% ~ 93% RH (non-condensing).
19. THERMOMETER SET
Thermometer set:
1. Thermometer
2. Battery 2 x 1.5V AAA size alkaline batteries
3. Soft bag
4.Instructions for use
20. UTILIZATION
The unit must be utilized in accordance with current standards
separately from domestic wastes. For utilizing it is necessary to
contact special organizations licensed to make utilization.
21. WARRANTY
Warranty period is 2 years from the date of purchase.
This warranty doesn’t cover any damages caused by improper
using, and also battery, protective cover and packaging. When a
manufacturing defect is revealed during the warranty period a faulty
unit would be repaired or, if repairing is impossible, replaced with
another one.
Manufacturing date is on the unit in a serial number: last 2 figures of
the year, then month number.
The manufacturer may change units partially or completely if
necessary, without prior notice.
ELECTROMAGNETIC COMPATIBILITY INFORMATION
Manufacturer’s Declaration of the Electromagnetic
Compatibility
Table 1
Guidance and manufacturer’s declaration –
еlectromagnetic emissions
Emissions test Compliance
RF emissions
CISPR 11 Group 1
RF emissions
CISPR 11 Class B
Harmonic emissions
IEC 61000-3-2 Not application
Voltage fluctuations/ flicker emissions
IEC 61000-3-3 Not application
Table 2
Guidance and manufacturer’s declaration –
еlectromagnetic immunity
Immunity test IEC 60601-1-2
Test level Compliance level
Electrostatic discharge
(ESD)
IEC 61000-4-2
±8 kV contact
±2 kV, ±4 kV, ±8 kV,
±15 kV air
±8 kV contact
±2 kV, ±4 kV, ±8 kV,
±15 kV air
Electrical fast transient/
burst
IEC 61000-4-4
Power supply lines: ±2 kV
input/output lines: ±1 kV Not application
Surge
IEC 61000-4-5
line(s) to line(s): ±1 kV.
line(s) to earth: ±2 kV.
100 kHz repetition
frequency
Not application
Voltage dips, short
interruptions and voltage
variations on power supply
input lines
IEC 61000-4-11
0% 0.5 cycle
At 0°, 45 °, 90 °,
135 °, 180 °, 225 °, 270 °
and 315 °
0% 1 cycle
And
70% 25/30 cycles
Single phase: at 0
0% 300 cycle
Not application
Power frequency
magnetic field
IEC 61000-4-8
30 A/m
50Hz/60Hz
30 A/m
50Hz/60Hz
Conduced RF
IEC 61000-4-6
150KHz to 80MHz:
3Vrms
6Vrms (in ISM and
amateur radio bands)
80% Am at 1kHz
Not application
Radiated RF
IEC 61000-4-3
10 V/m
80 MHz – 2,7 GHz
80 % AM at 1 kHz
10 V/m
80 MHz – 2,7 GHz
80 % AM at 1 kHz
NOTE UTis the a.c. mians voltage prior to application of the test level.
Remark In the presence of strong electromagnetic field (Horizontal/Vertical,
80MHz~180MHz and 1.4GHz~2GHz, 10V/m applied on the product), it will have
a change from 0.1°C to 0.3°C of the measured value. In case of malfunction due
to these strong electromagnetic fields, user need to wait till resume normal
operation without intervene.
IM_MED-3000_EN_5120
B.Well Swiss AG
Bahnhofstr. 24, 9443 Widnau, Switzerland
www.bwell-swiss.ch
Table 3
Guidance and manufacturer’s declaration –
electromagnetic Immunity
Radiated RF
IEC61000-4-3
(Test
specifications
for ENCLOSURE
PORT IMMUNITY
to RF wireless
communications
equipment)
Test
Frequency
(MHz)
Band
(MHz) Service
Modulation
Modulation
(W)
Distance
(m)
IMMUNITY
TEST
LEVEL
(V/m)
385 380 –
390 TETRA 400
Pulse
modulation
18 Hz
1,8 0.3 27
450 380 –
390
GMRS 460,
FRS 460
FM
± 5 kHz
deviation
1 kHz sine
2 0.3 28
710
704 –
787
LTE Band
13, 17
Pulse
modulation
217 Hz
0,2 0.3 9745
780
810
800 –
960
GSM
800/900,
TETRA 800,
iDEN 820,
CDMA 850,
LTE Band 5
Pulse
modulation
18 Hz
2 0.3 28
870
930
1720
1 700 –
1 990
GSM 1800;
CDMA
1900;
GSM 1900;
DECT;
LTE Band 1,
3, 4, 25;
UMTS
Pulse
modulation
217 Hz
2 0.3 28
1845
1970
Last revision 2020-W51
Memory Deletion
1. Remove one of the batteries, long press the ON Button.
2. Reload the battery until “ ” on the LCD screen.
Automatically on the 26th measurement: when the 25 memories have
been used up, any new measurement will be recorded and the oldest
memory deleted without you having to do anything.
NOTE:
All the readings will be cleared no matter record in Body Mode or
Object Mode.
15. CLEANING INSTRUCTIONS
For the device disinfection, 75% alcohol (available in the pharmacy)
can be used.
Measurement Sensor:
Please wipe with a clean and dry cotton swab to clean the Sensor on
the inside. Do not use water, the Sensor is not waterproof.
Thermometer:
Use a soft and dry cloth to clean the thermometer body. Do not use
abrasive cleaners. The body of the thermometer is not water-resistant.
Never put the thermometer under a running tap or submerge it into
water.
Store the thermometer in a cool and dry location. Free from dust and
away from direct sunlight. Do not expose the thermometer to extreme
temperatures, humidity, or shock.
16. TROUBLESHOOTING
FAULT OR
FAULT SYMBOL FAULT DESCRIPTION CORRECTIIVE
MEASURE
No display On
the LCD pane.
The battery has run
out. Incorrect battery
polarity.
Replace the
battery.
Please note:
The (+) side of
the battery must
face Positive (+)
indication on the
device.
Measurement
not possible (or
an abnormal
value is
displayed).
The thermometer is not
ready.
Wait until
the °C symbol is
displayed.
An abnormal
temperature
value is
displayed.
The Sensor is dirty or
damaged.
Clean the Sensor
or get it repaired.
The thermometer was
removed too early
(before the beep sound).
Wait until you
hear the beep
before removing
the thermometer
from the forehead.
or
symbol is
displayed.
The temperature
measured is outside the
measuring range.
Body Mode:
LO – temperature
<32°C (89.6°F).
HI – temperature
≥42,9°C (109.3°F)
Object Mode:
LO – temperature
<0°C (32°F).
HI – temperature
≥100°C (212°F).
Check that the
probe tip is clean
and that the
thermometer is
properly placed
on the forehead.
Symbol is
displayed. The battery has run out. Replace the
battery.
Err
Symbol is
displayed.
The ambient
temperature is
outside the operating
temperature range or is
changing too fast.
To ensure accurate
measurement, let
the thermometer
rest at operating
temperature for
30 minutes prior
to use.
22. SYMBOL INFORMATION
IP20
FOLLOW INSTRUCTIONS BEFORE USE
MANUFACTURER’S NAME
ARTICLE NUMBER
SERIAL NUMBER
TYPE BF EQUIPMENT
DISPOSAL FOR SEPARATE COLLECTION
CE MARK (0044)
OPERATING CONDITION,
TEMPERATURE 5˚C ~ 40˚C
STORAGE CONDITION,
TEPERATURE -25˚C ~ 70˚C
KEEP DRY
HOUSING INGRESS PROTECTION RATE: IP20
0044
40
5
-25
70
17. APPLIED STANDARDS
Device Standards:
Device Corresponds to the requirements of the standard for infrared
thermometers
IEC 60601-1:2012
IEC 60601-1-2:2014
ISO 80601-2-56:2009
Classification:
Anti-electric Shock Type: Internally powered equipment
Applied part: Type BF
Mode of operation: Continuous Operation
EMC: type B class I
Electromagnetic Compatibility:
Device fulfills the stipulations of the standard IEC 60601-1-2
The stipulations of EU-Directive 93/42/EEC for Medical Devices
Class Ila have been fulfilled.
18. PRODUCT SPECIFICATIONS
Measurement range:
Human Body:
Object:
32,0 ~ 42,9°C (89,6°F ~ 109,3°F)
0,0°C ~ 100°C (32,0°F ~ 211,8°F)
Accuracy:
For Body mode:
For Object mode:
±0,2°C (±0,4°F):
36,0°C ~ 39,0°C (96,8°F ~ 102,2°F)
±0,3°C (±0,5°F): out of the range
±1°C (±2°F):
0°C ~ 60,0°C (32,0°F ~ 140,0°F)
±4°C (±7,2°F): out of the range
Display resolution: 0,1°C or 0,1°F
Temperature unit: Default °C or Default °F
Operation Distance: 3 cm
Traffic lights backlight
(Body mode), Indicator
light range:
Green: <37,5°C (<99,5°F);
Yellow: ≥37,5°C - ≤37,9°C (≥99,5°F -
≤100,2°F);
Red: >37,9°C (>100,2°F)
Beeps definition: Power on and ready for working: a
short beep
Measurement finished:
1 long beep ≤37,9°C (100,2°F)
6 short beeps >37,9°C (100,2°F)
Memory: 25 mesurements
Auto shut-off: about 10 seconds after no using
Batteries: 2 x 1.5V AAA size alkaline batteries
Dimensions (L×W×H): 142,5 mm × 38 mm × 40 mm
Weight: 76g (Net: 54g)
Operating environment: Temperature:
+5°C ~ +40°C (41°F ~ 104°F);
Humidity:
15% ~ 93 % RH (non-condensing);
70Kpa-106Kpa.
Transport and Storage
environment:
Temperature:
-25°C ~ +70°C (-13°F ~ 158°F);
Humidity:
15% ~ 93% RH (non-condensing).
19. THERMOMETER SET
Thermometer set:
1. Thermometer
2. Battery 2 x 1.5V AAA size alkaline batteries
3. Soft bag
4.Instructions for use
20. UTILIZATION
The unit must be utilized in accordance with current standards
separately from domestic wastes. For utilizing it is necessary to
contact special organizations licensed to make utilization.
21. WARRANTY
Warranty period is 2 years from the date of purchase.
This warranty doesn’t cover any damages caused by improper
using, and also battery, protective cover and packaging. When a
manufacturing defect is revealed during the warranty period a faulty
unit would be repaired or, if repairing is impossible, replaced with
another one.
Manufacturing date is on the unit in a serial number: last 2 figures of
the year, then month number.
The manufacturer may change units partially or completely if
necessary, without prior notice.
ELECTROMAGNETIC COMPATIBILITY INFORMATION
Manufacturer’s Declaration of the Electromagnetic
Compatibility
Table 1
Guidance and manufacturer’s declaration –
еlectromagnetic emissions
Emissions test Compliance
RF emissions
CISPR 11 Group 1
RF emissions
CISPR 11 Class B
Harmonic emissions
IEC 61000-3-2 Not application
Voltage fluctuations/ flicker emissions
IEC 61000-3-3 Not application
Table 2
Guidance and manufacturer’s declaration –
еlectromagnetic immunity
Immunity test IEC 60601-1-2
Test level Compliance level
Electrostatic discharge
(ESD)
IEC 61000-4-2
±8 kV contact
±2 kV, ±4 kV, ±8 kV,
±15 kV air
±8 kV contact
±2 kV, ±4 kV, ±8 kV,
±15 kV air
Electrical fast transient/
burst
IEC 61000-4-4
Power supply lines: ±2 kV
input/output lines: ±1 kV Not application
Surge
IEC 61000-4-5
line(s) to line(s): ±1 kV.
line(s) to earth: ±2 kV.
100 kHz repetition
frequency
Not application
Voltage dips, short
interruptions and voltage
variations on power supply
input lines
IEC 61000-4-11
0% 0.5 cycle
At 0°, 45 °, 90 °,
135 °, 180 °, 225 °, 270 °
and 315 °
0% 1 cycle
And
70% 25/30 cycles
Single phase: at 0
0% 300 cycle
Not application
Power frequency
magnetic field
IEC 61000-4-8
30 A/m
50Hz/60Hz
30 A/m
50Hz/60Hz
Conduced RF
IEC 61000-4-6
150KHz to 80MHz:
3Vrms
6Vrms (in ISM and
amateur radio bands)
80% Am at 1kHz
Not application
Radiated RF
IEC 61000-4-3
10 V/m
80 MHz – 2,7 GHz
80 % AM at 1 kHz
10 V/m
80 MHz – 2,7 GHz
80 % AM at 1 kHz
NOTE UTis the a.c. mians voltage prior to application of the test level.
Remark In the presence of strong electromagnetic field (Horizontal/Vertical,
80MHz~180MHz and 1.4GHz~2GHz, 10V/m applied on the product), it will have
a change from 0.1°C to 0.3°C of the measured value. In case of malfunction due
to these strong electromagnetic fields, user need to wait till resume normal
operation without intervene.
IM_MED-3000_EN_5120
B.Well Swiss AG
Bahnhofstr. 24, 9443 Widnau, Switzerland
www.bwell-swiss.ch
Table 3
Guidance and manufacturer’s declaration –
electromagnetic Immunity
Radiated RF
IEC61000-4-3
(Test
specifications
for ENCLOSURE
PORT IMMUNITY
to RF wireless
communications
equipment)
Test
Frequency
(MHz)
Band
(MHz) Service
Modulation
Modulation
(W)
Distance
(m)
IMMUNITY
TEST
LEVEL
(V/m)
385 380 –
390 TETRA 400
Pulse
modulation
18 Hz
1,8 0.3 27
450 380 –
390
GMRS 460,
FRS 460
FM
± 5 kHz
deviation
1 kHz sine
2 0.3 28
710
704 –
787
LTE Band
13, 17
Pulse
modulation
217 Hz
0,2 0.3 9745
780
810
800 –
960
GSM
800/900,
TETRA 800,
iDEN 820,
CDMA 850,
LTE Band 5
Pulse
modulation
18 Hz
2 0.3 28
870
930
1720
1 700 –
1 990
GSM 1800;
CDMA
1900;
GSM 1900;
DECT;
LTE Band 1,
3, 4, 25;
UMTS
Pulse
modulation
217 Hz
2 0.3 28
1845
1970
Last revision 2020-W51
Memory Deletion
1. Remove one of the batteries, long press the ON Button.
2. Reload the battery until “ ” on the LCD screen.
Automatically on the 26th measurement: when the 25 memories have
been used up, any new measurement will be recorded and the oldest
memory deleted without you having to do anything.
NOTE:
All the readings will be cleared no matter record in Body Mode or
Object Mode.
15. CLEANING INSTRUCTIONS
For the device disinfection, 75% alcohol (available in the pharmacy)
can be used.
Measurement Sensor:
Please wipe with a clean and dry cotton swab to clean the Sensor on
the inside. Do not use water, the Sensor is not waterproof.
Thermometer:
Use a soft and dry cloth to clean the thermometer body. Do not use
abrasive cleaners. The body of the thermometer is not water-resistant.
Never put the thermometer under a running tap or submerge it into
water.
Store the thermometer in a cool and dry location. Free from dust and
away from direct sunlight. Do not expose the thermometer to extreme
temperatures, humidity, or shock.
16. TROUBLESHOOTING
FAULT OR
FAULT SYMBOL FAULT DESCRIPTION CORRECTIIVE
MEASURE
No display On
the LCD pane.
The battery has run
out. Incorrect battery
polarity.
Replace the
battery.
Please note:
The (+) side of
the battery must
face Positive (+)
indication on the
device.
Measurement
not possible (or
an abnormal
value is
displayed).
The thermometer is not
ready.
Wait until
the °C symbol is
displayed.
An abnormal
temperature
value is
displayed.
The Sensor is dirty or
damaged.
Clean the Sensor
or get it repaired.
The thermometer was
removed too early
(before the beep sound).
Wait until you
hear the beep
before removing
the thermometer
from the forehead.
or
symbol is
displayed.
The temperature
measured is outside the
measuring range.
Body Mode:
LO – temperature
<32°C (89.6°F).
HI – temperature
≥42,9°C (109.3°F)
Object Mode:
LO – temperature
<0°C (32°F).
HI – temperature
≥100°C (212°F).
Check that the
probe tip is clean
and that the
thermometer is
properly placed
on the forehead.
Symbol is
displayed. The battery has run out. Replace the
battery.
Err
Symbol is
displayed.
The ambient
temperature is
outside the operating
temperature range or is
changing too fast.
To ensure accurate
measurement, let
the thermometer
rest at operating
temperature for
30 minutes prior
to use.
22. SYMBOL INFORMATION
IP20
FOLLOW INSTRUCTIONS BEFORE USE
MANUFACTURER’S NAME
ARTICLE NUMBER
SERIAL NUMBER
TYPE BF EQUIPMENT
DISPOSAL FOR SEPARATE COLLECTION
CE MARK (0044)
OPERATING CONDITION,
TEMPERATURE 5˚C ~ 40˚C
STORAGE CONDITION,
TEPERATURE -25˚C ~ 70˚C
KEEP DRY
HOUSING INGRESS PROTECTION RATE: IP20
0044
40
5
-25
70
17. APPLIED STANDARDS
Device Standards:
Device Corresponds to the requirements of the standard for infrared
thermometers
IEC 60601-1:2012
IEC 60601-1-2:2014
ISO 80601-2-56:2009
Classification:
Anti-electric Shock Type: Internally powered equipment
Applied part: Type BF
Mode of operation: Continuous Operation
EMC: type B class I
Electromagnetic Compatibility:
Device fulfills the stipulations of the standard IEC 60601-1-2
The stipulations of EU-Directive 93/42/EEC for Medical Devices
Class Ila have been fulfilled.
18. PRODUCT SPECIFICATIONS
Measurement range:
Human Body:
Object:
32,0 ~ 42,9°C (89,6°F ~ 109,3°F)
0,0°C ~ 100°C (32,0°F ~ 211,8°F)
Accuracy:
For Body mode:
For Object mode:
±0,2°C (±0,4°F):
36,0°C ~ 39,0°C (96,8°F ~ 102,2°F)
±0,3°C (±0,5°F): out of the range
±1°C (±2°F):
0°C ~ 60,0°C (32,0°F ~ 140,0°F)
±4°C (±7,2°F): out of the range
Display resolution: 0,1°C or 0,1°F
Temperature unit: Default °C or Default °F
Operation Distance: 3 cm
Traffic lights backlight
(Body mode), Indicator
light range:
Green: <37,5°C (<99,5°F);
Yellow: ≥37,5°C - ≤37,9°C (≥99,5°F -
≤100,2°F);
Red: >37,9°C (>100,2°F)
Beeps definition: Power on and ready for working: a
short beep
Measurement finished:
1 long beep ≤37,9°C (100,2°F)
6 short beeps >37,9°C (100,2°F)
Memory: 25 mesurements
Auto shut-off: about 10 seconds after no using
Batteries: 2 x 1.5V AAA size alkaline batteries
Dimensions (L×W×H): 142,5 mm × 38 mm × 40 mm
Weight: 76g (Net: 54g)
Operating environment: Temperature:
+5°C ~ +40°C (41°F ~ 104°F);
Humidity:
15% ~ 93 % RH (non-condensing);
70Kpa-106Kpa.
Transport and Storage
environment:
Temperature:
-25°C ~ +70°C (-13°F ~ 158°F);
Humidity:
15% ~ 93% RH (non-condensing).
19. THERMOMETER SET
Thermometer set:
1. Thermometer
2. Battery 2 x 1.5V AAA size alkaline batteries
3. Soft bag
4.Instructions for use
20. UTILIZATION
The unit must be utilized in accordance with current standards
separately from domestic wastes. For utilizing it is necessary to
contact special organizations licensed to make utilization.
21. WARRANTY
Warranty period is 2 years from the date of purchase.
This warranty doesn’t cover any damages caused by improper
using, and also battery, protective cover and packaging. When a
manufacturing defect is revealed during the warranty period a faulty
unit would be repaired or, if repairing is impossible, replaced with
another one.
Manufacturing date is on the unit in a serial number: last 2 figures of
the year, then month number.
The manufacturer may change units partially or completely if
necessary, without prior notice.
ELECTROMAGNETIC COMPATIBILITY INFORMATION
Manufacturer’s Declaration of the Electromagnetic
Compatibility
Table 1
Guidance and manufacturer’s declaration –
еlectromagnetic emissions
Emissions test Compliance
RF emissions
CISPR 11 Group 1
RF emissions
CISPR 11 Class B
Harmonic emissions
IEC 61000-3-2 Not application
Voltage fluctuations/ flicker emissions
IEC 61000-3-3 Not application
Table 2
Guidance and manufacturer’s declaration –
еlectromagnetic immunity
Immunity test IEC 60601-1-2
Test level Compliance level
Electrostatic discharge
(ESD)
IEC 61000-4-2
±8 kV contact
±2 kV, ±4 kV, ±8 kV,
±15 kV air
±8 kV contact
±2 kV, ±4 kV, ±8 kV,
±15 kV air
Electrical fast transient/
burst
IEC 61000-4-4
Power supply lines: ±2 kV
input/output lines: ±1 kV Not application
Surge
IEC 61000-4-5
line(s) to line(s): ±1 kV.
line(s) to earth: ±2 kV.
100 kHz repetition
frequency
Not application
Voltage dips, short
interruptions and voltage
variations on power supply
input lines
IEC 61000-4-11
0% 0.5 cycle
At 0°, 45 °, 90 °,
135 °, 180 °, 225 °, 270 °
and 315 °
0% 1 cycle
And
70% 25/30 cycles
Single phase: at 0
0% 300 cycle
Not application
Power frequency
magnetic field
IEC 61000-4-8
30 A/m
50Hz/60Hz
30 A/m
50Hz/60Hz
Conduced RF
IEC 61000-4-6
150KHz to 80MHz:
3Vrms
6Vrms (in ISM and
amateur radio bands)
80% Am at 1kHz
Not application
Radiated RF
IEC 61000-4-3
10 V/m
80 MHz – 2,7 GHz
80 % AM at 1 kHz
10 V/m
80 MHz – 2,7 GHz
80 % AM at 1 kHz
NOTE UTis the a.c. mians voltage prior to application of the test level.
Remark In the presence of strong electromagnetic field (Horizontal/Vertical,
80MHz~180MHz and 1.4GHz~2GHz, 10V/m applied on the product), it will have
a change from 0.1°C to 0.3°C of the measured value. In case of malfunction due
to these strong electromagnetic fields, user need to wait till resume normal
operation without intervene.
IM_MED-3000_EN_5120
B.Well Swiss AG
Bahnhofstr. 24, 9443 Widnau, Switzerland
www.bwell-swiss.ch
Table 3
Guidance and manufacturer’s declaration –
electromagnetic Immunity
Radiated RF
IEC61000-4-3
(Test
specifications
for ENCLOSURE
PORT IMMUNITY
to RF wireless
communications
equipment)
Test
Frequency
(MHz)
Band
(MHz) Service
Modulation
Modulation
(W)
Distance
(m)
IMMUNITY
TEST
LEVEL
(V/m)
385 380 –
390 TETRA 400
Pulse
modulation
18 Hz
1,8 0.3 27
450 380 –
390
GMRS 460,
FRS 460
FM
± 5 kHz
deviation
1 kHz sine
2 0.3 28
710
704 –
787
LTE Band
13, 17
Pulse
modulation
217 Hz
0,2 0.3 9745
780
810
800 –
960
GSM
800/900,
TETRA 800,
iDEN 820,
CDMA 850,
LTE Band 5
Pulse
modulation
18 Hz
2 0.3 28
870
930
1720
1 700 –
1 990
GSM 1800;
CDMA
1900;
GSM 1900;
DECT;
LTE Band 1,
3, 4, 25;
UMTS
Pulse
modulation
217 Hz
2 0.3 28
1845
1970
Last revision 2020-W51
Table of contents
Other B.Well Thermometer manuals
