BABI Alert Plus User manual

BABI ALERT PLUS
Instruction Manual

About the product
Babi Alert Plus Key Ring Device is an accessory device that
operates with the phone App as a reminder device in the
case that the user leaves both their mobile phone and infant
unattended. When the user moves away from the car the
device will sound an alarm and flash a LED light until the
baby is removed or the alarm has been cancelled. If this
alarm is not resolved then the mobile app will send an alarm
message and GPS co-ordinates o the others users. Without
the App the Babi Alert Plus is the principle alarm device.
The key ring device must be paired with the app and can
handle up to four seat pads simultaneously.
What’s in the box
Babi Alert Plus Key Ring Device x 1
Key Ring and rope x 1
Instruction Manual x 1
1
Note: Please read this manual carefully
before use the device, and observe the safety
rules listed and keep it for future reference.

Product Specification
Product Name Babi Alert Plus
Product Code BAP1001
Dimension Ф48 * 15mm
Operating temperature -20°C to +60°C
Rated Voltage DC 3V
Rated Power ≤50mW
Communication
Technology Bluetooth Low Energy
Input Power
(Replaceable)
Primary 3V CR2450
battery (not rechargeable)
2

LED indicator/Switch
Speaker
Coin opener Battery
replacement door
3
Product Specification

To turn on the device:
Press down the Switch for 1 second. To
confirm that the device is working
properly a red LED will flash once. If the
battery has less than 20% charge, the
product sound an alert and will flash a
red LED light continuously to warn the
user that the battery needs replacing.
To activate the Alert device:
The Alert device it needs to be paired
with the mobile phone App.
1. Press on the heart on the
BABI Logo on the Home page of
the App. A photo of the device
will automatically appear in
black and white.
How to use the Babi Alert Plus
When the Babi Alert Plus Device is used with the Babisit App
it will work as a secondary alarm. However when it used
without the App, Babi Alert Plus is the Primary alarm.
USING THE DEVICE WITH THE APP
1
4

2. Press the “CONNECT” bar to automatically pair the
device with the Smart Cushion via the App. When the
device is paired, the photo of the device will change
from black and white to full color.
3. Press “BACK” bar to return to the main menu, where a
green battery icon will have appeared above the BABI
logo, this is a battery charge level indicator of the
accessory paired device.
2
3
5

The now paired device, is now fully operational and will always
be connected to the Mobile Phone App on standby. In the case
that the mobile phone and infant have been left in unattended.
When the user walks away from the car about 12-15 meters the
Alert keyring device will go into an Alarm state and sound an
audio alert and flash its LED Light continuously. The device will
keep in this ALERT Alarm state until the button is either pressed
to deactivate it or the Infant is removed from the Baby Car Seat.
If the alarm is not be resolved by removing the Mobile App will
proceed to send an ALARM notification message with the GPS
coordinates, to all the preset associated users for example:
“( NAME ) WAS ABANDONED AT GPS 22.3213 N 113.9433 E”.
The associated users can then open a map and see the exact
position of where the infant has been left and a rescue can be
put into action.
Device Battery Check :At any time if user presses the button for
1 second, the led will flash from 1 to 4 times indicating the
charge status of the battery. If the led flashes only once, the
battery will need to be replaced.
6

3
USING THE DEVICE WITHOUT THE APP
Without the App Babi Alert Plus will act as the Primary alarm and
sound an alarm when the user moves away from the vehicle and
has left an infant unattended in the vehicle. An audio and visual
alarm is raised that will remain in an alarm state until the child is
removed from the BABI Smart cushion or manually cancelled.
(Note: One BABI Alert Plus device can be work used with up to 4BABI
Smart Cushions when used without the App).
The device must be paired with the Babi smart cushion. To do
this: 1. Press the button for 1 second to turn on the device, a
beep sound will confirm the device is turned on.
Once the device is on, to pair it with the cushion:
2. Press the button again for 6 seconds to turn on the pairing
mode (this is only required the first time the device is paired with the cushion).
3. Press the BABI Logo in center of the Babi Cushion until a beep
sound is heard. This alert indicates the alert device is now
connected to the smart cushion and is ready for use. 7
1 & 2

Additional Notes for the BABI Alert Plus Device:
-In normal function the led light will flash every 8 to 10
seconds this indicates that the battery is full. If the
led light flashes very fast continuously the battery
needs to be replaced.
-To cancel an Alarm press the button on the device for
1 Second.
‐If the pairing communication connection is lost for
any reason the device will go into alarm mode.
‐To cancel this paired connection the button must be
held down for 6 seconds at power on.
Warranty
The product is guaranteed against any non-conformity
defect within normal operational conditions of use. The
warranty shall not therefore apply in the case of damages
caused by improper use, wear or accidental damage
events.
Note: The battery is not included in the warranty as it is a
consumable item that needs to be replacd when required.
8

Declaration of compliance
BABI Ltd declare that this Babi Alert Plus key ring device
complies with and conforms to all the necessary EU
regulations and legislations. The product is CE and FCC
certified and is ROHS compliant.
Manufacturer
BABI. Ltd
20F Mongkok Commercial Centre,
16 Argyle Street, Mongkok,
Kowloon, Hong Kong
MADE IN CHINA
NOTE: A Lithium battery is used in this device. Please ensure
that when a new battery is installed that the battery is placed
the correct way. Please dispose of old battery carefully and in
special waste container.
Customer Support
For additional information and assistance, please contact
us by sending us an email to this address:
[email protected] 9

www.babisit.com
Made in PRC by BABI Ltd Hong Kong

FCC Statement
This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates
uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
•Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The device can be used
in portable exposure condition without restriction.
ISED Statement
‐English: This device complies with Industry Canada license‐exempt RSS standard(s).
Operation is subject to the following two conditions: (1) This device may not cause interference,
and (2) This device must accept any interference, including interference that may cause
undesired operation of the device. The digital apparatus complies with Canadian CAN ICES‐3
(B)/NMB‐3(B).
‐French: Le présentappareilestconforme aux CNR d'Industrie Canada applicables aux appareils
radio exempts de licence. L'exploitationestautorisée aux deux conditions suivantes: (1) l'appareil
ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareildoit accepter tout
brouillageradioélec triquesubi, mêmesi le brouillageest susceptible d'encompromettre le
fonctionnement.
This radio transmitter (ISED certification number: 26215-BAP1001) has been approved by
Industry Canada to operate with the antenna types listed with the maximum permissible gain
indicated. Antenna types not included in this list, having a gain greater than the maximum gain
indicated for that type, are strictly prohibited for use with this device.
Le présent émetteur radio (ISED certification number: 26215-BAP1001) a été approuvé par
Industrie Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un
gain admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est
supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur.