Bachmann Williams GENESIS User manual

– Page 1 of 2 –
Bachmann Industries, Inc.
1400 East Erie Avenue, Philadelphia, PA 19124 USA
www.bachmanntrains.com
Customer Service Telephone [phone]
GENESIS DUMMY DIESEL LOCOMOTIVE INSTRUCTIONS
Thank you for purchasing a Williams by Bachmann® locomotive. This locomotive has been manufactured to provide
years of use and enjoyment. Please follow the simple instructions below.
Before operating, please lightly lubricate the points shown in the diagram below. Do not over-lubricate and take extra care
to avoid getting lubricants on the wheel surfaces.
1. For the axles and coupler pivot points Marked A, we recommend that you lubricate with a small amount of light
oil such as Bachmann E-Z Lube® #99984 Light Gear Oil. Do not over-lubricate.
2. For areas that require electrical flow, such as roller pick-ups Marked B, please use Bachmann E-Z Lube®
#99981 Conductive Contact Lube. Never use any Teflon® based oil on these areas because this type oil has
insulating properties.

– Page 2 of 2 – Printed In China
OPERATION
After unpacking the locomotive, make sure that the uncoupling plunger is in the correct position with the pin inserted in
the knuckle (see figure 1). Failure to do so will allow the uncoupling plunger to contact the center rail and a direct short
will occur when power is applied to the track.
Uncoupling
This dummy locomotive is equipped with operating knuckle couplers at both ends. To uncouple, position the uncoupling
plunger over the center of electro-magnetic track uncoupling section and activate the magnet.
PERIODIC MAINTENANCE
Disassembly Instructions
You will have to remove the body shell for bulb replacement, or to install a power upgrade kit. The body shell is attached
with four screws on the bottom of the locomotive frame. The screws are located in each corner of the frame. When you re-
attach body shell, please be careful not to over-tighten the screws.
Lubrication
We recommend that you lubricate as directed on page 1 every 10 hours of operation.
Light Bulb Replacement
This locomotive uses a 12 volt bayonet style bulb. The standard replacement bulb number is 53.
Power Upgrade Kit
A power upgrade kit, Williams by Bachmann® #00241, is available to convert this dummy unit into a powered unit.
Please follow the installation instructions that are included with the kit.

Bachmann Industries, Inc.
Genesis (dummy) Parts List Rev 08.14.08 Printed in China
,
1400 East Erie Ave, Philadelphia, PA 19124 USA
www.bachmanntrains.com
Customer Service Tele
p
hone 800-356-3910
P
art
N
um
b
e
r
D
escr
i
pt
i
on
N
um
b
er
U
se
d
GENESIS BODY & BODY PARTS
691-M014B Metal Frame 1
1
-
30100DFT
Screw(Mounts Body to Frame)
4
1
-
30100DFT
Screw(Mounts
Body
to
Frame)
4
691-01-01 Body Shell 1
322-02-01 Ornamental Horn 2
691-X001 Front Window Glass 1
691-X002R1 Side Window Glass 2
691-X003 Rear Window Glass 4
691-03-01 Fuel Tank 1
690-02-06 Lar
g
e Lens 2
690 02 06
Large
Lens
2
690-02-07 Small Lens 6
1-26060DPM Screw(Mounts Fuel Tank to Frame) 2
TRUCK PARTS
293-M023FR1 Flanged Wheel 8
293-M029NR5 Axle 4
1-30140DPM Truck Mounting Screw 2
293-E001 Operating Coupler Assembly 2
691-02-01 Front Pilot 1
335-04-01 Rear Pilo
t
1
1-23040DPWB Pilot Mounting Screw 2
293-E002R1 Roller Pickup Assembly 1
293-01-02 Top Insulator for Roller Pickup 2
293-01-03 Bottom Insulator for Roller Pickup 2
1-26220DPM Roller Pickup Mounting Screw 2
691
-
02
-
02
Sideframe
4
691-02-02
Sideframe
4
1-30060DPM Sideframe / Bolster Mounting Screw 10
293-10-03BR1 Truck Mount 2
293-M013R1B Truck Bolster 2
See Diagram on opposite side for identification. Parts shown in Italics are not illustrated.
Genesis (dummy) Parts List Rev 08.14.08 Printed in China