Baicells BS6430E User manual

LTE-Turbo BS
Configuration Guide
for BS6430E
Document Version: 01
All rights reserved © Baicells Technologies Co., Ltd.

About This Document
This document describes the configuration of the LteTurbo BaseStation for software version
BaiAP_LT_1.2.x. It is a guide that how to configure the device after its installation
completes.
Copyright Notice
Baicells Technologies, Inc., copyrights the information in this document. No part of this
document may be reproduced in any form or means without the prior written consent of
Baicells Technologies, Inc.
Disclaimer
The information in this document is subject to change at any time without notice. For more
information, please consult with a Baicells technical engineer or the support team.
Revision Record
Date
Version
Description
08 Oct, 2021
01
Initial released.
Contact Us
Baicells Technologies Co., Ltd.
Baicells Technologies North America, Inc.
China
North America
Address
9-10F,1stBldg.,No.81BeiqingRoad,Haidian
District,Beijing,China
555 Republic Dr., #200, Plano, TX 75074,
USA
Phone
400-108-0167
[phone]
Email
[e-mail] or
[e-mail]
[e-mail] or
[e-mail]
Website
www.Baicells.com
https://na.Baicells.com

1
Menu
1. Configuration Overview ..............................................................................................2
2. Installation ...................................................................................................................2
Part & Materials ........................................................................................................ 2
Led.............................................................................................................................. 4
3. Login Web Client.........................................................................................................6
Web Client Environmental Requirements............................................................... 6
Connect Web Client to Base Station........................................................................ 6
Set Up Client Computer ............................................................................................ 6
Log In.......................................................................................................................... 8
4. Wizard ........................................................................................................................10
First Page ................................................................................................................. 10
Second Page ............................................................................................................ 10
5. Overview Info .............................................................................................................12
6. WAN/VLAN Setting ...................................................................................................14
7. Network Management Setting ..................................................................................14
8. Turbo Wireless Setting .............................................................................................15
9. Ngmwan Setting ........................................................................................................15
10. Lte Basic Setting .......................................................................................................16
11. Lte Core Network Setting .........................................................................................17
12. Lte Sync Setting ........................................................................................................17
13. Log Setting ................................................................................................................18
14. Upgrade .....................................................................................................................18
15. Restore Factory Setting............................................................................................19
16. NTP Config ................................................................................................................19
17. Diagnostics ................................................................................................................20
18. Certificate...................................................................................................................20
19. License.......................................................................................................................21
20. Reboot........................................................................................................................21

1.Configuration Overview
The Baicells LteTurbo BS is loaded with its own GUI for configuring its operating
parameters. You can log in to the GUI either locally through the Local Maintenance
Terminal (LMT), which is an Ethernet port, or remotely via IP address. You can also use
the Baicells Operations Management Console (OMC) to configure the eNB; this
document, however, focuses only on using the eNB GUI.
After the LteTurbo base station is powered on, it is necessary to configure the base
station to access the user and provide data service.
NOTE: Before configuring the BS’s data, data planning needs to be done first. The data to configure
includes local parameters and connecting parameters. These parameters are either provided by the
user or determined after negotiation with the customers. The data to prepare include IP address, wifi
parameters, ngmwan parameters, software version, and so on.
The LteTurbo base station needs to configure at least the wifi name, password, and
working frequency.
2.Installation
Part & Materials
Item
Qty
Picture
Nova430T unit
1

Power Cable
1
PoE Power Adaptor
1
You will need standard tools, Ethernet cable, ground wire, and RJ-45 connectors for
installing and connecting the outdoor unit.
The Port with lable “WAN” is the PoE port,Picture as follows:

Led
The LED lamp indicated the current base station status with 4 lights: PWR, RUN, ACT,
BHL (see figure below)
⚫PWR
Green light on Power Supply is normal
Green light off Power Supply is wrong
⚫RUN
Red light flashes,Green light off Upgrading…
Red light on,Green light off wifi not work
Red light off,Green light on wifi work,no station connected
Red light off,Green light flashes wifi work,some stations connected
⚫ACT
Green light off enodeb is abnormal
Green light flashes enodeb is normal
⚫BHL
Green light off WAN port(Fiber or Copper) has no IP

Green light on WAN port(Fiber or Copper) has IP and Communication
is good.
Note: The status of the lamp is meaningless during the start-on process,
and wait for the start-on (5 minutes) before checking the LED status.

6
3.Login Web Client
Web Client Environmental Requirements
Table 3-1 describes the requirements on computer of the client.
Table 3-1 Environmental Requirements of the Client
Item
Description
CPU
Above Intel Core 1GHz
Memory
Above 2G RAM
Hard disk
No less than 100 MB space available
Operating system
Microsoft: Windows XP, Windows Vista or Windows7
Mac: MacOSX10.5 or above
Screen resolution
Above 1024 x 768
Browser
Chrome 6 or higher
Connect Web Client to Base Station
Connect the Ethernet interface of the computer to the LAN interface of the base
station through the Ethernet cable.
Set Up Client Computer
Before logging into the Web client, the client computer’s IP address needs to be set
up first so that the connection between the client and the server is possible. Take
Windows 7 as an example:
1. Click “Start>Control Panel” and later “Network and Internet” in the window
that pops up.
2. Click “View network status and tasks” and later “Local Connectivity” in the
window that pops up.
3. In “Status of Local Connectivity”, click “Properties” to see the “Properties of
Local Connectivity” pop-up window.
4. Select “Internet Protocol Version (TCP/IPV4)” and click “Properties” to see
the pop-up window as Figure 3-.

7
Figure 3-1 Internet Protocol Version (TCP/IPV4)
Select either “Obtain an IP address automatically” or “Use the following IP
address”:
If “Obtain an IP address automatically” selected, go directly to step 7
If “Use the following IP address” selected, follow step 5 ~ step 7
NOTE: In general, if the auto obtaining fails, one needs to set up the IP address manually.
5. Select “Use the following IP address”.
6. Input IP address, subnet mask, and default gateway, and then click “OK”.
IP address: 192.168.150. XXX: (recommended XXX: 100~254)
Because the LAN interface of the base station uses the IP address of
192.168.150.1, others should avoid using this address.
Subnet mask: 255.255.255.0
Default gateway: 192.168.150.1
7. In the command window, execute ping 192.168.150.1 and check whether the
connection between the client computer and the server works or not.

8
Log In
1. Open a web browser, and enter http://192.168.150.1, as shown in Figure 3-1.
Figure 3-1 GUI Login
2. Input user name, password, and click “Login”. The homepage is given in Figure 3-2.

9
Figure 3-2 GUI Homepage
NOTE: The information may vary by product type or software version.
The front page shows the information as the basic information and status
information of the LteTurbo base station.The status information is dynamically
refreshed, refreshed every 3 seconds.
On the left side of the home page is the navigation pane, showing the information as
Status-> Overview.On the top of home page,showing the Basic information of the
base station, such as device model, hardware version, software version, SN model.
The status information area displays the WLAN connection status, rate statistics,
LAN port connection status, and a list of connection devices.

10
4.Wizard
The first login will automatically pop up the wizard page, and you can also manually click
the "Basic Settings" -> "Wizard" menu to pop up the wizard page.The wizard contains
two parts:
First Page
In this page, you can set the network management address and other information, and
then you can choose the auto or manual button, as shown in the figure below:
Second Page
Auto setting is not supported by current version.
Manual setting page is show as follows:

11

12
5.Overview Info
The overview page include such information:
1. Basic Information -- Include SW/HW Version, SN
2. Lte PRB Usage
3. Turbo Rate Curve
4. Device Status:
Turbo switch,OMC Status,Cell Status,CA Status,Halob Status,Turbo
Connection,Turbo Setting

13
Numbers of online devices of various types
LTE Turbo UE: support Turbo and LTE
LTE UE: only support LTE
Virtual Networks: virtual devices, not support now
Public Services: only support WiFi
Status of services
Gray line: not open
Blue tape fork: opened but not connected
Blue line: opened and connected
5. Device Health
Contains four parts: equipment health, network health, business health, interference
detection
Device health includes running time, CPU load and other information is not
supported

14
6.WAN/VLAN Setting
Support for dynamic / static IP configuration, VLAN configuration, dns configuration, mtu
configuration
7.Network Management Setting
Support Config Network Management URL

15
8.Turbo Wireless Setting
9.Ngmwan Setting
ngmwan setting items：
select nw ifnames
select ngmwan interface
ip addr
config server ip
net mask
subnet mask
mode
server
one client
only support one client
bind port
bind port
log
enable/disable log

16
auto peer
auto setting peer
dhcp
enable dhcp server
dhcp startip
dhcp start ip
dhcp endip
dhcp end ip
dhcp mask
dhcp mask
10. Lte Basic Setting
SAS Setting
Select “USA-FCC(CBRS)” in box ,
SAS Setting will be shown below.

17
11. Lte Core Network Setting
12. Lte Sync Setting

18
13. Log Setting
14. Upgrade