Baicells EG3015M-M30-HP User manual

EG3015M-M30-HP
Configuration Guide
Document Version: 01
All rights reserved © Baicells Technologies Co., Ltd.

About This Document
This document describes the configuration of the LteTurbo CPE for EG3015M-M30-HP. It is a
guide that how to configure the device after its installation completes.
Copyright Notice
Baicells Technologies Co., Ltd., copyrights the information in this document. No part of this
document may be reproduced in any form or means without the prior written consent of
Baicells Technologies Co., Ltd.
Disclaimer
The information in this document is subject to change at any time without notice. For more
information, please consult with a Baicells technical engineer or the support team.
Revision Record
Date Version Description
22 July, 2022 01 Initial released.
Contact Us
Baicells Technologies Co., Ltd. Baicells Technologies North America,
Inc.
China North America
Address 9-10F,1stBldg.,No.81BeiqingRoad,Haidian
District,Beijing,China
555 Republic Dr., #200, Plano, TX 75074,
USA
Phone [phone] [phone]
Email [e-mail] or
[e-mail]
[e-mail] or
[e-mail]
Website www.Baicells.com https://na.Baicells.com

1
Menu
1. Configuration Overview .................................................................................................. 1
2. Installation ....................................................................................................................... 1
Part & Materials .............................................................................................................. 1
2.1
Led .................................................................................................................................... 2
2.2
3. Configuration .................................................................................................................... 4
Status Menu ..................................................................................................................... 4
3.1
3.1.1 Overview .................................................................................................................... 4
3.1.2 Routes ...................................................................................................................... 11
Network Menu ............................................................................................................... 12
3.2
3.2.1 LAN Settings ............................................................................................................. 12
3.2.2 WAN Settings ........................................................................................................... 14
3.2.3 WLAN Settings ......................................................................................................... 17
3.2.4 Static Routes ............................................................................................................ 20
3.2.5 DMZ ......................................................................................................................... 20
LTE Menu ........................................................................................................................ 22
3.3
3.3.1 Connection Settings ................................................................................................. 22
3.3.2 Scan Mode ............................................................................................................... 24
3.3.3 APN Management ................................................................................................... 28
3.3.4 PIN Management ..................................................................................................... 29
Security Menu ................................................................................................................ 30
3.4
3.4.1 Firewall Settings ...................................................................................................... 30
3.4.2 MAC Filter ................................................................................................................ 31
3.4.3 IP Filter ..................................................................................................................... 32
3.4.4 URL Filter ................................................................................................................. 33
3.4.5 Port Forwarding ....................................................................................................... 34
3.4.6 Port Triggering ......................................................................................................... 35
3.4.7 ALG........................................................................................................................... 35

3.4.8 UPnP ........................................................................................................................ 37
3.4.9 Attack Protection ..................................................................................................... 38
VPN Menu ....................................................................................................................... 39
3.5
3.5.1 IPSec ........................................................................................................................ 39
3.5.2 OpenVPN ................................................................................................................. 41
System Menu .................................................................................................................. 43
3.6
3.6.1 NTP .......................................................................................................................... 43
3.6.2 Account .................................................................................................................... 44
3.6.3 Dynamic DNS ........................................................................................................... 45
3.6.4 WEB Setting ............................................................................................................. 48
3.6.5 FTP Auto Upgrade .................................................................................................... 49
3.6.6 TR-069 ...................................................................................................................... 50
3.6.7 SNMP ....................................................................................................................... 52
3.6.8 Restore/Update ....................................................................................................... 54
3.6.9 Ping Watchdog......................................................................................................... 55
3.6.10 SAS ......................................................................................................................... 56
3.6.11 SAS Certificates ...................................................................................................... 60
3.6.12 System Messages ................................................................................................... 61
3.6.13 Diagnosis ................................................................................................................ 61
3.6.14 Reboot ................................................................................................................... 65
Logout ............................................................................................................................. 66
3.7
4. Regulatory Compliance ................................................................................................. 67
FCC Compliance .................................................................................................................... 67

1
1. Configuration Overview
The Baicells LteTurbo CPE is loaded with its own GUI for configuring its operating
parameters. You can log in to the GUI either locally through the Local Maintenance
Terminal (LMT), which is an Ethernet port, or remotely via IP address. You can also use
the Baicells Operations Management Console (OMC) to configure the CPE; this
document, however, focuses only on using the web GUI.
2. Installation
Part & Materials
2.1
Item Qty Picture
EG3015M-M30-HP unit 1
DC Power Adaptor 1

You will need standard tools, Ethernet cable, ground wire, and RJ-45 connectors for
installing and connecting the outdoor unit.
Led
2.2
The CPE has 4 lights, divided into 5 groups according to the function:
lte signal light, power light, LTE light, WLAN light,LAN light (see
figure below).
 WLAN light
1. 8 ssids are all off, red/green off
2. Red light on during startup
Startup completed Red light off
3. One SSID is on, green on and red off
4. A user successfully accesses, 1s green flash
 Lte signal light
Strong signal green light on, red light off
weak signal red light on, green light off
 Power light
The power light is bright, indicating that the power supply is normal,
otherwise the power supply is abnormal
 LTE light

1. SIM card is abnormally red
2. Red flash without network access
3. Successful network access, green light and red light out
 Lan light
1. The speed is 10/100Mbsps, and the orange and green lights are on
at the same time
2. The speed is 1000Mbsps, and the green light is on
Note: The status of the lamp is meaningless during the start-on process,
and wait for the start-on (5 minutes) before checking the LED status.

4
3. Configuration
Status Menu
3.1
3.1.1 Overview
After logging in, the GUI opens to the Status > Overview page (Figure 3-1). This page is
a dashboard of key information regarding the CPE.

Figure 3-1 Overview
 The equipment connection status pane displays the connection status of CPE
equipment with LTE network and WAN network. The icons are described as follows:
LTE signal
For SIM card, it is gray when checking SIM / disconnect, orange
when SIM card is recognized, and red after network access.
WiFi signal: red when WiFi is on and gray when WiFi is off.
Wired interface, gray when there is no link, orange when negotiating
100M, and blue when negotiating 1000M.
LTE network bearer. It is gold in case of bearing and gray in case of
no bearing. The number next to the icon is WAN uplink and downlink
data rate.
User Number under LAN
CPE equipment icon, click to modify the equipment name.
 The Basic Info pane displays the product model, module name, LAN MAC, IMEI,
serial number, etc.

 The Wifi Config pane displays the SSIDs of the CPE device. Click the icon to
jump to the WLAN settings page for WiFi configuration.
 The LTE Signals pane shows the signal quality of primary cell. Click icon to view
LTE details, such as the CPE's SIM card status and its IMSI and IMEI numbers,
wireless frequency being used, eNB connection status, and current signal strength
and quality.
 Under WAN Throughput you will see downlink (DL) and uplink (UL) data rates for
current throughput (kbps), average rates, peak rates, and total throughput.The flow
statistics can be carried out at different times, including 2 min, 1 hour, 1 day and 7

days.
 The Device Health pane shows device health data, such as CPU Usage, Memory
Usage, USIM Status, LTE/NR Connection Time, System Up Time, etc.
 The Diagnosis pane shows Ping diagnosis results, Traceroute diagnosis results,
Ping Wathchdog configuration data. Click the displayed data to quickly enter the
configuration page.
 The WAN Connections pane displays configured APN, IP address of gateway and
DNS.

 The LAN Connections pane will show details about all smart devices currently
connected through the CPE.
 The WiFi Associated Stations pane shows the device information currently
accessing WiFi.
Refer to Table 3-1for a description of the Status fields.
Table 3-1 Status
Field Name Description
Basic Info
Product Model CPE model number
Market Name Market name of CPE products
Module Name Type of LTE module in the CPE
LAN MAC The MAC address of the LAN port. The same as the MAC on the
label.
IMEI International Mobile Equipment Identity is like a serial number for the
SIM card
SN Serial Number
Wifi Config
SSID 2.4G service set ID
5GSSID 5G service set ID
LTE Signals
USIM Status The Universal Subscriber Identity Module, or SIM, card status is
either available or not ready in the CPE

Field Name Description
IMSI The unique International Mobile Subscriber Identity (IMSI) number
associated with the SIM card in the subscriber's CPE. The IMSI
must be identifiable by the operator's LTE network in order to access
it.
LTE Mode The LTE network operates with either Time Division Duplexing
(TDD) or Frequency Division Duplexing (FDD)
IMEI International Mobile Equipment Identity is like a serial number for the
SIM card
PLMN The Public Land Mobile Number (PLMN), or operator network ID, to
which the CPE is connected
Band The range of frequencies within the band the CPE may use for
wireless communications with an eNB, expressed in MHz
Cell ID The operator's cell site ID to which the CPE is connected. A cell site
may comprise more than one eNB. Each eNB is given a PCI to
identify it.
RSRQ Reference Signal Receiving Quality indicates the quality of the
wireless signal
eNB ID The operator's cell site ID to which the CPE is connected. A cell site
may comprise more than one eNB. Each eNB is given a PCI to
identify it.
EARFCN The E-UTRA Absolute Radio Frequency Channel Number (band
and frequency) within which the CPE operates
PCI The Physical Cell Identifier (PCI) unique to each eNB. PCI indicates
to which eNB the CPE is connected. An operator can have multiple
eNBs serving the same cell.
DL Frequency The frequency, in MHz, being used in the downlink (eNB to CPE). In
LTE, the carrier frequency in the uplink and downlink is designated
by the EARFCN, which identifies the LTE band and carrier
frequency.
UL Frequency The frequency, in MHz, that the CPE is using in the uplink (CPE to
eNB). In LTE, the carrier frequency in the uplink and downlink is
designated by the EARFCN, which identifies the LTE band and
carrier frequency.
CINR The Channel Signal-to-Interference-plus-Noise Ratio reflects the
signal strength of the signal received from the two antennas in the
eNB, expressed in decibels (dB)
NOTE: Additional SINR values are reported when a transmitting
device is using more than two antennas.

Field Name Description
RSRP1 ~ RSRP4 The Signal-to-Interference-plus-Noise Ratio reflects the signal
strength of the signal received from the two antennas in the eNB,
expressed in decibels (dB)
NOTE: Additional SINR values are reported when a transmitting
device is using more than two antennas.
WAN Throughputs
DL The current downlink data throughput rate, in Kbps
UL The current uplink data throughput rate, in Kbps
Average The average DL and UL data throughput rates, in Kbps, for this CPE
in the last 3 minutes
Peak The peak DL and UL data throughput rates, in Kbps, for this CPE in
the last 3 minutes
Sum The total (sum) DL and UL data throughput rates, in Kbps
Device Health
CPU Usage CPU real-time usage rate, updated every 3s
Memory Usage The memory usage rate of CPE, updated every 3s
USIM Status The Universal Subscriber Identity Module, or SIM, card status is
either available or not ready in the CPE
Connection State Connection status between the CPE and the network –Checking
SIM, Scanning, Registering, Acquiring IP, Connected,
Disconnected.
IMSI The unique International Mobile Subscriber Identity (IMSI) number
associated with the SIM card in the subscriber's CPE. The IMSI
must be identifiable by the operator's LTE network in order to access
it.
System Up Time CPE start time
LTE/NR
Connection Time
LTE/NR network access success time
Firmware Version Version number of the module
Firmware Build
Time
Software version compilation time
Hardware Version CPE hardware version
Module Version CPE LTE module firmware version
Diagnosis
Ping Ping diagnosis results
Traceroute Traceroute diagnosis results
Ping Watchdog Ping Watchdog configuration result
WAN Connections
Profile Name APN Number
IPv4 Address/ IPv6
Address
IPv4or IPv6 address of the APN gateway

Field Name Description
IPv4 DNS/ IPv6
DNS
IPv4 or IPv6 DNS
LAN Connections
Device Name The name of each smart device connected through the CPE
MAC Address The MAC address of each smart device connected through the CPE
IP Address The IP address of each device connected through the CPE
Lease Time Amount of time a smart device’s IP address has been leased
Type Type of smart device connection
WiFi Associated Stations
SSID WIFI SSID
MAC Address MAC address of the device accessing the SSID
IP Address IP address of the device accessing the SSID
Signal The signal strength of the connected device
Noise WiFi signal noise
RX Rate Wi-Fi real-time receiving rate
TX Rate Wi-Fi real-time transmission rate
3.1.2 Routes
The Overview > Routes table lists all of the configured routing rules, including Allocation
and Retention Policy (ARP) tables and active IPv4/IPv6 routes (Figure 3-2). For each
item in the list, the IP address, MAC address, and interface type are displayed.

Figure 3-2 Routes
Network Menu
3.2
3.2.1 LAN Settings
Enter the Network > LAN host IP address, subnet mask, and the Maximum Transmission
Unit (MTU) size, in bytes (Figure 3-3). The range is 1000-2000 bytes. The default is 1500
bytes.
Figure 3-3 LAN settings
You can enable or disable the DHCP server (Figure 3-4). If enabled, enter the start and
end IP addresses, and the lease time for IP address use - from 10 minutes to 720 hours.
Optionally, you can enter one or two DNS server IP addresses, and one to three option
138 connection IP addresses for connecting to a Control and Provisioning of Wireless

Access Points (CAPWAP) server. When using option 138, the device will connect with
the server's LAN port and get an Access Controller (AC) IP address.

Figure 3-4 DHCP settings
The DHCP Reservations may be used to bind an IP address to a specific MAC address
(Figure 3-5). In the bottom half of the pane, enter the IP address and the MAC address,
and click on ADD. The IP address must be within the range of DHCP addresses. Any
configured bindings will appear at the top of the window.
Figure 3-5 Bundled Address List
3.2.2 WAN Settings
3.2.2.1 NAT Mode
The CPE will be worked at NAT mode, and only 1 APN can be configured by Default
Data bear types.

Figure 3-6 WAN Settings
DNS Mode set how to get DNS server IP:
 Automatic: automatically obtain the DNS server IP assigned by EPC. If Manually
DNS is not selected, it is automatic mode.
 Manually: manually configure the primary and standby DNS server IP.
3.2.2.2 Tunnel Mode
This CPE can support L2TP, GRE, PPTP, and VxLAN VPN type.

Figure 3-7 Tunnel Mode
3.2.2.3 Bridge Mode
When the CPE worked at Bridge mode, the WAN ports address will bridge to LAN port,
and the LAN port will work at trunk mode.