Ballard Designs BUNNY WILLIAMS JM113 User manual

Prevent accidentally discarding small parts or
hardware. Retain all carton contents until assembly
and installation are complete.
DO NOT USE POWER TOOLS FOR ASSEMBLY
Over-tightening will strip wood and/or break parts.
Gently Hand Tighten Hardware and Components
PRODUCTS ARE NOT INTENDED
FOR COMMERCIAL USE.
UPDATED: 1-11-2022 Page 1 of 5
PRODUCT NAME: BW Kent Arbor
ITEM NUMBER: JM113
ASSEMBLED DIMENSIONS : 108”H x 92”W x 62”D
MADE IN VIETNAM
Customer Service: 800-367-2810
Online: www.ballarddesigns.com

Page 2 of 5
Ltr.
A28
B 20
Qty. Hardware Included
Ltr.
D
E
4
4
Qty. Components
C32
REQUIRED TOOLS:
Allen Wrench (included)
-Two person assembly suggested.
Remove all parts, hardware and
protective packaging from carton
and carefully arrange on a clean,
level, padded surface.
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
Do not over-torque assembly bolts!
Over tightening may cause wood to crack,
embedded nuts to pull out or other damage.
Avoid power tools. Hand tighten only.
CAUTION
Allen Bolt
M6 x 55mm
Allen Screw
M7 x 70mm
Allen Bolt
M6 x 40mm
Allen Screw
M7 x 50mm
Allen Wrench
F
G
H
I
J
K
L
M
N
O
1
4
2
2
4
4
4
2
2
2
Cleaning and Care
Occasionally wipe or hose down to remove dirt and debris.
Promptly remove spills.
Do not use harsh chemicals or abrasive cleaners.
Arched Top (F)
Top Brackets (G)
Left Sides (H)
Right Sides (I)
Brackets (J)
Single Hole
Brackets (L)
Three Holes
Finials (K)
Side Panels (M)
Top Sides (N)
Seats (O)
Assemble in location for intended use.

STEP 1: Invert Arched Top (F) onto a level, padded surface and attach a Top Bracket (G) to each
corner using four Allen Screws (A) as illustrated. Hand tighten until secured.
STEP 2: Locate a Left and Right Side (H,I). Note that each Side has a high and low upright. Attach
Bracket (J) to higher upright and secure by inserting and tightening a Finial (K) until secured. Next,
attach Bracket (L) to lower upright and secure using three Allen Screws (A). Hand tighten until secured.
IMPORTANT: Take note of illustration for this step to ensure proper assembly.
NOTICE: Steps 2 through 5 are repeated to create both LEFT and RIGHT Side Assemblies.
Page 3 of 5
(G)
(F)
(A) x 4
(H) (I)
(J)
(K)
(L)
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
Assemble in location for intended use.
Higher Upright
Lower Upright
(A) x 3

STEP 3: Place a Side Panel (M) onto a level, padded surface then orient Left Panel (H) as illustrated.
Use four Allen Bolts (C) in the middle section and one Allen Bolt (B) at each end (top and bottom). Fully
tighten all Bolts using Allen Wrench (E).
(C)
(B)
(H)
(I)
(M)
(B)
STEP 4: Carefully fit Right Side (I) onto opposite side of Side Panel (M). Secure using four Allen
Bolts (C) in the middle section and one Allen Bolt (B) at each end (top and bottom). Fully tighten
all Bolts using Allen Wrench (E).
(C)
(B)
(B)
Page 4 of 5
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
Assemble in location for intended use.

(F)
(D)
(C)
(B)
(N)
(O)
(B)
Page 5 of 5
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
STEP 5: Complete Side Assembly by adding Seat (O) and securing with six Allen Bolts (B), three on
each side as illustrated. Add Top Side (N) and secure using two Allen Screws (D) on each side as
illustrated. Fully tighten all Bolts and Screws using Allen Wrench (E).
STEP 6: On a level surface, carefully stand each Side Assembly and with at least two people lift
and fit Arched Top (F) onto Side Assemblies as illustrated. Secure using four Allen Bolts (C)
inserted from lower side into each corner hole in Bracket (L). Fully tighten using Allen Wrench (E).
REPEAT STEPS 2 THROUGH 5 TO CREATE REMAINING SIDE ASSEMBLY.
STOP
(C)
(C)