Ballard Designs JC334 User manual

PRODUCT NAME: Ceylon Porch Swing
ITEM NUMBER: JC334
ASSEMBLED DIMENSIONS : 28.7”H x 65”W X 37”D
PRODUCTS ARE NOT INTENDED
FOR COMMERCIAL USE.
UPDATED: 8/15/2019 Page 1 of 6
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
MADE IN VIETNAM

Customer Service: 800-367-2810
Online: www.ballarddesigns.com Page 2 of 6
REQUIRED TOOLS:
-Screwdriver
-Wrench (included)
-Allen Wrench (included)
-Assembly requires 2 people.
-Installation requires a
licensed contractor*
Ltr.
A 2 Short Eye Bolt
B2Long Eye Bolt
C 4 Washer
D8Nut
E2110mm Screw
F 2 25mm Screw
L - Bracket
G2
H 4 70mm Screw
Left Arm (O)
Right Arm (P)
Seat (R)
Qty. Hardware Included
Ltr.
K 4
O 1
P 1
Q 1
R 1
S 1
J 4
I 90mm Screw
4
Qty. Components
Remove all parts, hardware and
protective packaging from
carton and carefully arrange
on a clean, level, padded surface.
NOTE: To prevent accidentally
discarding small parts or
hardware, retail all carton
contents unti assembly and
installation are complete.
Wooden Plug
Chain
Wrench
Allen Wrench
4
1
2
L
M
N
50mm Screw
ASSEMBLE SWING IN AREA FOR INTENDED USE
Back (Q)
Cushion (S)

Page 3 of 6
STEP 1: Insert a Short Eye Bolt (A) into Left Arm (O) and Right Arm (P) as shown below. Add Washer (C)
followed by two Nuts (D). Use Wrench (M) to fully and firmly tighten.
NOTE: Two nuts are required to prevent Eye Bolt from coming loose over time.
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
(C)
(Q)
(D)
STEP 2: Attach Long Eye Bolt (B) to Back (Q) as shown below. Add Washer (C) followed by two
Nuts (D). Use Wrench (M) to fully and firmly tighten.
(A)
(O) (P)
(D) (C)
(B)

Page 4 of 6
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
STEP 3: Gently fit dowel on end of Seat (R) into hole on Left Arm (O) and Right Arm (P). Position
L-Bracket (G) as illustrated then insert 110mm Screw (E) from side into Seat. Add 25mm Screw (F) to
bottom and tighten both using Allen Wrench (N). Finally, fully secure Seat to both arm by inserting 70mm
Screws (H) through Seat and into Arms as illustrated. Use Allen Wrench to full and firmly tighten.
STEP 4: Attach Back (G) to Left (O) and Right (P) arms using 90mm Screws (I). Tighten using Allen
Wrench (N). Attach Seat (R) to Back using 50mm Screws (J). Firmly tighten using Allen Wrench.
(G)
(O)
(P)
(I)
(R)
(J)
(J)
(I)
(R)
(O)
(P)
(G)
(E)
(F)
(R)

Page 5 of 6
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
STEP 5: Insert Wood Plugs (K) into all screw holes on back of Swing.
STEP 6: Swing can support up to 800 lbs. *To prevent personal or property damage, all swings
should be installed by a Licensed Building Contractor. Hanging hardware is not included as it
needs to be determined on site. Building support beams must be adequately designed and/or
reinforced to support at least the rating of the swing. Connect Chains (L) to Eye Bolts (A,B).
(K)
WARNING
Falling Hazard
SWING MUST BE SUPPORTED BY ADEQUATE STRUCTURE
Consult with a Licensed Building Contractor before installation.

Page 6 of 6
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
STEP 7: Place Seat Cushion (S) onto Swing
Cleaning and Care
Please refer to care instructions on product hang tag.
(S)