Ballard Designs Madison Poolside Chaise JC152 User manual

PRODUCT NAME: Madison Poolside Chaise
ITEM NUMBER: JC152
DIMENSIONS OF ITEM ASSEMBLED: 42 1/2”H x 24 3/4”W X 79”L
Page 1 of 5
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
MADE IN VIETNAM
PRODUCTS ARE NOT INTENDED
FOR COMMERCIAL USE.
UPDATED: 4/11/2019

Customer Service: 800-367-2810
Online: www.ballarddesigns.com Page 2 of 5
TOOLS NEEDED:
Assembly requires 1 or
more people.
Ltr.
A 10 Allen Screws
Left Legs (G)
Cross Bars (H)
Right Legs (I)
Middle Left Leg (J) Middle Right Leg (K)
Chaise Frame (L)
Back Cover (M)
Back Supports (N)
Seat Supports (P)
Seat Cover (O)
C
D
14
B 4
25mm Allen Bolts
14
E 10 Screw Plugs
F 2 Allen Wrenches
Nuts
40mm Allen Bolts
Qty. Hardware Included
Ltr.
G 2
K 1
H 3
N 2
O 1
I 2
J 1
M
1L
1
P 2
Qty. Components

Page 3 of 5
STEP 1:
STEP 1:
Attach a Left and Right Leg (G & I) to the ends of a Crossbar (H) using Allen Screws (A) and
an Allen Wrench (F). Repeat for the remaining Left and Right Leg (G & I) and a Crossbar (H).
NOTE: Make sure the peg holes are facing the same direction.
STEP 2:
STEP 2:
Attach the Middle Left Leg (J) and Middle Right Leg (K) to the remaining Crossbar (H) using
Allen Screws (A) and an Allen Wrench (F).
STEP 3:
STEP 3:
Attach the assembly from STEP 1 to each end of the Chaise Frame (L) by screwing
the remaining Allen Screws (A) into the Left and Right Legs (G & I) using an Allen Wrench (F).
STEP 4:
STEP 4:
Attach the assembly from STEP 2 to the underside of the Chaise Frame (L) by screwing in
the 40mm Allen Bolts (B) into the Middle Left and Right Legs (J & K) using an Allen Wrench (F).
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
(J)
(I)
(G)
(G)
(I)
(G)
(H)
Peg Hole
(H)
(A)
(A)
(A)
(A)
(K)
(K)
(B)
(L)

Page 4 of 5
STEP 5: Slide the Back Supports (N) into the pockets on the edge of the Back Cover (M).
Slide the Seat Supports (P) into the pockets on the edge of the Seat Cover (O).
STEP 6: Insert the assembled Seat Cover (O) and Back Cover (M) inside channels on the sides of the
Chair Frame (L). Tighten the 25mm Allen Bolts (C) through the inside of the Chair Frame (L)
and into the Nuts (D) on the outside of the Frame (L). Use both Allen Wrenches (F) to hold
and tighten the Nuts (D) and Bolts (C).
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
(O)
(P)
(N)
(M)
Channel
(D)
(C)
(L)
(O & P)
(O & P)
(M & N)
(M & N)
(L)

Page 5 of 5
STEP 7: Turn the Chaise upright and lightly tap the Screw Plugs (E) into the screw holes on the
sides and ends.
STEP 8: Pull the back rest of the Chaise up and lock it into the desired position.
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
Clean & Care
Please refer to the care instructions on the hang tag.
(E)