Ballard Designs JM100 User manual

PRODUCTS ARE NOT INTENDED
FOR COMMERCIAL USE.
UPDATED: 11-11-2020 Page 1 of 7
PRODUCT NAME: Sunday Daybed with Cushion and Canopy
ITEM NUMBER: JM100
ASSEMBLED DIMENSIONS: 76”H x 82”W x 43 1/3”D
MADE IN VIETNAM
Prevent accidentally discarding small parts or
hardware. Retain all carton contents until assembly
and installation are complete.
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
DO NOT USE POWER TOOLS FOR ASSEMBLY
Over-tightening will strip wood and/or break parts.
Gently Hand Tighten Each Component Together

Page 2 of 6
Ltr.
A 2
B
Extra Large Screws (100mm)
Large Screws (90mm)10
Qty. Hardware Included
Ltr.
M4
L 1
K 1
J 1
I1
Qty. Components
C 4 Medium Screws (50mm)
REQUIRED TOOLS:
Allen Wrench (included),
Rubber Mallet
-Assembly requires 2 people
D 4
E
Small Screws (30mm)
Connector Brackets2
F 10
G 2
H1
Wooden Plugs
Allen Wrench
Right Assembly (K)
Left Assembly (J)
Back (I)
Seat (H)
Panel Rods (M)
Cleaning and Care
Occasionally wipe or hose down to remove dirt and debris.
Promply remove spills.
Do not use harsh chemicals or abrasive cleaners.
Cross Bar (L)
N
O
P
2
1
1
Side Panels (N)
Top Panel (O)
Cushion (P)
DO NOT USE POWER TOOLS
FOR ASSEMBLY
Gently Hand Tighten
Components
Assemble in location for intended use.
Customer Service: 800-367-2810
Online: www.ballarddesigns.com

Assemble in location for intended use.
Page 3 of 6
Place Hooks (A) into holes on top of Right Arm (I) and Left Arm (J). Thread and firmly
STEP 1: Orient Seat (H) and Back (I) as illustrated then insert Extra Large Screws (A) through Seat
and into Back. Fully tighten using Allen Wrench (G).
STEP 2: Orient and attach Left Assembly (J) to Seat/Back. Insert Large Screws (B) as illustrated and
tighten using Allen Wrench (G). Further secure using Medium Screws (C) inserted and tightened as
illustrated.
Next, attach Cross Bar (L) as illustrated and secure using Large Screw (B). Tighten using Allen
Wrench (G).
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
(H)
(I)
(A)
(J)
(B)
(B)
(B)
(B) (H)
(C)
(C)
(L)

Page 4 of 6
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
STEP 3: Orient and attach Right Assembly (K) to Seat/Back. Insert Large Screws (B) as illustrated
and tighten using Allen Wrench (G). Further secure using Medium Screws (C) inserted and tightened
as illustrated.
Next, attach Cross Bar (L) as illustrated and secure using Large Screw (B). Tighten using Allen
Wrench (G).
(B)
(B)
(C)
(L)
(K)
STEP 4: Turn Daybed Assembly upright onto its Legs. Secure Back (I) to Left and Right Assemblies
(J,K) by attaching Connector Brackets (E) as illustrated using Small Screws (D). Fully tighten using Allen
Wrench (G).
(J)
(K)
(D)
(E)
(E)
(E)
(D)
(D)

Page 5 of 6
(F)
(F)
(M)
Attach Chains (G) to Hooks (A).
STEP 5: COVER VISIBLE HOLES. Insert a Wooden Plug (F) into each hole on side of Right Arm (I)
and Left Arm (J). NOTE: A Rubber Mallet may be required to gently tap and seat Plug.
STEP 6: Insert Panel Rods (M) into pockets on edge of each Side Panel (N) (Fig. 1) then fit Rod
ends into LOWER notches on top of Left and Right Assemblies (J,K) (Fig. 2).
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
(F)
(F)
(F)
Fig. 1
Fig. 2
(M)
(N)
(M)
(J)
(K)
Hang Side Panels in
LOWER NOTCH

(M)
Page 6 of 6
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
Fig. 2
(M)
(O)
Fig. 1
STEP 7: Insert remaining Panel Rods (M) into end pockets on Top Panel (O) (Fig. 1) then fit Rod ends
into UPPER notches on top of Left and Right Assemblies (J,K) (Fig. 2)
Hang Top Panel in
UPPER NOTCH
(J)
(K)
STEP 8: Place Cushion (P) onto Daybed.
(P)