Ballard Designs Toulouse MV362 User manual

PRODUCT NAME: Toulouse Tall Bookcase
ITEM NUMBER: MV362
DIMENSIONS OF ITEM ASSEMBLED: 84"H x 42 1/2"W x 16"D
PRODUCTS ARE NOT INTENDED
FOR COMMERCIAL USE.
UPDATED: 4/15/2015 Page 1 of 6
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
MADE IN INDIA

Customer Service: 800-367-2810
Online: www.ballarddesigns.com Page 2 of 6
TOOLS NEEDED:
-Assembly requires 2 or more people.
-Assembly requires a screwdriver.
-1/16” Drill Bit and Power Drill.
Ltr.
A 4 Allen Bolts and Cap Nuts
B 12 Allen Bolts
C 2 Wood Screws
D 1 Wrench
E 1 Allen Wrench
F 2 Anti Tip Kits
Top Fixed Shelf (G)
Middle Fixed Shelf (H)
Bottom Fixed Shelf (I)
Left Side Frame (K)
Right Side Frame (L)
X- Shape Back (M)
Left Shelf Supports (N)
Right Shelf Supports (O)
Shelf Guards (P)
Qty. Hardware Included
Ltr.
K 1
N 3
L 1
M 1
P 10
O 3
J 3
H 1
I 1
G 1
Qty. Components
Adjustable Shelves (J)
NOTE: When unpacking, lay the parts
on a padded surface such as the
packaging provided. Be sure to locate
all hardware before throwing
away any packaging.

Page 3 of 6
STEP 1:
NOTE: Assemble the Bookcase in the desired location.
Assemble Bookcase on a smooth, clean surface such as the packaging provided. Loosely
attach the Top Fixed Shelf (G) to the tops of the Left and Right Side Frames (K & L) using
the Allen Bolts (B). Then loosely attach the Bottom Fixed Shelf (I) to the bottoms of the
Side Frames using the Allen Bolts.
NOTE: Do not fully tighten the Allen Bolts.
STEP 2: Attach the X-Shape Back (M) to the Left and Right Side Frames (K & L). Align the ends of
the X-Shape to the tabs at the top and bottom of the Frames. The predrilled holes in the
X-Shape should be at the bottom of the X. The Back should be attached behind the Frame
tabs. Unscrew the assembled Allen Bolts and Cap Nuts (A) and insert the Bolts from the back
and tighten the Cap Nuts using the Wrench (D). Fully tighten the Allen Bolts (B) attaching
the Top and Bottom Fixed Shelves (G & I) with the Allen Wrench (E).
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
(G)
(B)
(G)
(L)
(L)
(K)
(L)
Predrilled
Holes
(K)
(I)
(D)
(A)
(M)
(M)

Page 4 of 6
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
(H)
STEP 3: Stand Bookcase upright and lay the Middle Fixed Shelf (H) on the center support bars of the
Left and Right Side Frames (K & L) with the notches facing the front. To get the Shelf in place,
tilt it back and lay it flat on the supports. Attach the Frames and Shelf from underneath
using the Allen Bolts (B) and Allen Wrench (E).
STEP 4: Attach the X-Shape Back (M) to the Middle Fixed Shelf (H) using the Wood Screws (C) and
a screwdriver.
NOTE: Assemble the Bookcase in the desired location.
(L)
(K)
(M)
(M)
(C)
(H)
(H)

Page 5 of 6
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
(M)(K)(I)(G)(E)(C)(A) (L)(J)(H)(F)(D)(B)
(O)
(N)
(N)
(L)
(K)
(K)
STEP 5: Insert the Left and Right Shelf Supports (N & O), with equal spacing, on the respective
Side Frames (K & L) by inserting the Shelf Support fronts into the holes in the Side Frame’s
front first and then sliding the back of the Shelf Support into the corresponding key hole in
the Side Frame’s Back. Make sure the Shelf Supports are securely locked into place and
are in a horizontal position.
STEP 6: Lay the Adjustable Shelves (J) on the Shelf Supports (N & O) with the notches facing
the front of the Side Frames. To get the Shelves in place, tilt them back and lay them flat
on the Supports.
(J)
(K)
(L)
NOTE: Assemble the Bookcase in the desired location.

2 Retention Belts
2 Brackets
Qty.
2
2
Qty.Hardware Included
Screws
Anchors
Hardware Included
Cleaning & Care:
Apply a very thin coat of wax with a soft cloth and keep away from direct sunlight.
Page 6 of 6
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
Wall
(G)
Anti Tip Installation: Screw the Brackets in the Anti Tip Kits (F) into wall studs or use
a 1/16” Drill Bit to screw a pilot hole to tap in an Anchor and screw in the Screws. The Screws should
be 2 Inches below the D-Rings already attached to the Bookcase. Align the Brackets and D-Rings
vertically and string in the Retention Belts. Confirm Straps are securely laced and locked.
NOTE: It is ideal that at least one screw goes into a stud.
(P)
(K)
(P)
NOTE: Assemble the Bookcase in the desired location.
STEP 7: Insert the Shelf Guards (P) into the Side Frames (N & O) by inserting the Guards into
the front holes of the Side Frames first and then sliding the back of the support into the
corresponding key hole in the Side Frames back. Make sure the button on the Guard
is facing inward and the Guards are in a horizontal position.