Bally MONTE CARLO S6000 User manual

BALLY S6000 MONTE CARLO - QUICK SET-UP GUIDE
1) If this is a ew set up, begi with setti g up the progressive Cham II board. Make sure the
Mikoh Cham II Eprom is i stalled o the board as ofte times it is removed by the casi o for security
reaso s. If this is a pre-ru i g machi e a d you have allowed your rechargeable battery to die o your
Cham II board the proceed to Step 2. If your Cham II is fu ctio i g properly a d showi g your correct
jackpot amou t i the display wi dow the proceed to Step 5 below.
2) Make sure the display is hooked up a d the power up the Mikoh box. Set up the o -board
optio s usi g the toggle switch a d butto s with the display powered o . Use the followi g setti gs:
Me u = SYST
Test = OFF
Birth = OFF
Save to = RAMD
Show load = YES
Show C1 = YES
Symbol = NONE
Sou d = Disable
Me u = ADDR
GRADDR = 4
ID ADDR = 64
RTE ADDR = OFF
MACH ADDR = 2

Me u = DISP
JP Limit = NO
#displays = 1
JP Group = SA0
Mfile = 4
ODSpeed = 10
Fo t1 = FLIP18
Size = 60
3) You ow eed to program the parameters o your Cham II. If you wa t us to set up the Cham II
board a d charge (re-charge) the battery for you, ship the u it alo g with a $40 payme t for services
a d retur shippi g expe se. Or, if you ca do this yourself, co ect the serial cable from your
computer to the Cham II a d start the PSP3.0 program. If you require the PSP program a d diagram for
buildi g the cable co tact us. O ce the program is started e ter the "Jackpot Programmi g" sectio a d
e ter the followi g parameters:
F3 = SINGLE
F4 = M-08
F5 = 3 SEC
F6 = JP0
F7 = $$$$
F8 = MS-00
E ter the desired base Jackpot "base" a d "curre t" values. Hidde Jackpot should be zero. Jackpot
limit should be 999,999. I creme t 1, I suggest 12000. I creme t 2 leave at zero.
After all the i formatio is ready, press F1 to se d to the display. Verify that the correct jackpot amou t
is ow displayed a d there are o "C" errors.
4) Rei stall the Cham II i to the top box of the machi e a d reco ect all har esses to the display
a d fi ally, rei stall the glass i to the machi e bei g careful ot to pi ch a y of the Cham II wires.

5) Remove the mai computer board a d test the battery with your volt meter. If it is below 3.1
volts it eeds to be replaced. A ew battery should read 3.6 volts or higher. Note that batteries o Bally
S6000 boards require extreme heat to remove properly. We have our statio set at 415 degrees for
proper removal. If you are usi g a less sophisticated "home use" device where you ca ot co trol
temperature, we advise that i stead of removi g the curre t battery e tirely, cut the leads, removi g
the battery a d leavi g it's soldiered leads i place. Shorte the leads o your ew battery a d soldier
to the existi g leads.
Now study the board a d i sure the followi g setti gs are i place, ote this is assumi g you are 25 ce t
de omi atio a d you are usi g a WBA bill validator. Co tact us if you have somethi g else.
DS1
1=ON
2=ON
3=ON
4=ON
5=OFF
6=ON
7=ON
8=ON
DS2
1=OFF
2=OFF
3=ON
4=OFF
5=ON
6=OFF
7=ON
8=ON
DS3
ALL ON
Now look at your jumpers:
JW1 = OFF
JW2 = RIGHT 2 PINS COVERED
JW3 = RIGHT 2 PINS COVERED
JW4 = BOTTOM 2 PINS COVERED
JW5 = LEFT 2 PINS COVERED
JW6 = RIGHT 2 PINS COVERED
JW7 = OFF
JW8 = LEFT 2 PINS COVERED
JW9 = BOTTOM 2 PINS COVERED
JW11 = RIGHT 2 PINS COVERED
JW12 = ON
JW13 = TOP 2 PINS COVERED
JW14 = TOP 2 PINS COVERED
JW15 = OFF
JW16 = RIGHT 2 PINS COVERED
JW18 = OFF
JW20 = ON

6) If ot already placed, i stall the perso ality chips U18 a d U20 chips o the board. Remove the
"mai s" U28 a d U43 chips. Temporarily i stall the U28 a d U43 Clear chips i their positio s. Place
the board back i to the machi e. Press a d co ti ue to hold the "Test" a d "Pseudo Coi " butto s o
the board a d power o . Co ti ue to hold u til the butto s o the deck flash o a d off co ti uously.
Let go of the butto s a d power the machi e off. Replace the origi al U28 a d U43 mai s back i to the
machi e.
7) After the board is place back i to the machi e, i sure that the small cable is i stalled at the
fro t left of the board. Power the machi e back o leavi g the door ope . After it boots back up the
display o the reel glass will show a bu ch of umber with the far left o e flashi g. Press the "cha ge /
atte da t" butto o e time to clear. The display should go to "50". Press the test butto o the board
co ti uously u til the display reads "11d". O ce you see 11d, stop pressi g the butto . The display will
cha ge to 27 o the left a d 001 o the right.
You must ow go through the parameter a d cha ge the setti gs for each. The umber o the left is
the parameter a d o the right is its curre t optio setti g. Read carefully....to cycle to the ext
parameter press the Bet Max butto . To cha ge the curre t setti g o the parameter you are looki g at
press the Spi butto . Most setti gs you will ot cha ge....a d leave as the default, o ly cha ge the
o es listed below. Cycle to each parameter listed below a d cha ge from the default setti g to the ew
o e listed.
If you have coin mechanics:
Parameter Setti g
9 4
2 4
7 1
56 160
78lo 1
51 5000
58 1000

73 0
61 1
81 1
If you do not have coin mechanics, and you are hand pay only:
Parameter Setti g
9 4
2 4
7 1
56 0
78lo 1
51 5000
58 1000
73 0
61 1
81 0