banks six-gun User manual

09/14/12 PN 96808 v.14.0
Banks Six-Gun®/
EconoMind®&
Banks Brake®
For use with Six-Gun/EconoMind Selector
Switch
2003-07 Ford Power Stroke
6.0L Turbo-Diesel
THIS MANUAL IS FOR USE WITH SYSTEMS 55467, 55468, 61023 , 63743, 63745
Owner’sManual
with Installation Instructions

296808 v.14 .0
Banks iQ System
(P/N 61151-61152)
- 5” touchscreen interface that can
control the Banks Diesel Tuner and/or
SpeedBrake on the fly.
- Interchangable gauge display, read
and clear codes, monitor engine
diagnostics, log data, time your
vehicles runs and much more.
Banks Monster®Exhaust System
Sport (P/N 48790-48793)
Single and Dual (P/N 47285-47292,
47606-47609, 48783-48788)
- Increases exhaust flow, cuts
backpressure, lowers exhaust gas
temperatures (EGTs) and increases
power.
Banks Ram-Air Intake System
(P/N 42155)
- Increases your airflow over stock.
- Adds power, improves fuel economy,
lowers EGTs and reduces smoke.
High-Ram Intake
(P/N 42750-42751)
- Increases flow and provides more
uniform air distribution to the
engine for more available power at
a given boost level.
Banks Techni-Cooler®System
(P/N 25974-25975)
- Provides increased air flow to the
engine by increasing air density for
more increased power, lower EGTs
and improved fuel economy.
Banks Brake
(P/N 55467-55468)
- Increases the stopping power of
your truck and extends the service
life of your brakes
Boost and Pyro Gauges
(P/N 64507)
- Keep your engine safe by
monitoring vital engine parameters
Products available from Banks Power
for 2003-2007 Ford 6.0L

96808 v.14.0 3
Banks Billet Torque Converter
(P/N 72522)
- Higher torque capacity over stock
- Lockup clutch is slip-resistant so
transmission fluids stay cooler and
transmission life is prolonged.
Banks SpeedBrake
iQ Compatible (P/N 55455-55456)
PDA Compatible (P/N 55457-55458)
- Allows for controlled hill decent at
a user defined vehicle speed.
Banks Bullet
(P/N 66524-66525)
- Adds power safely to your vehicle
- Displays critical engine functions
- Engine safeguards
- Change power levels on-the-fly
Banks Diesel Tuner
Six-Gun w/ switch (P/N 61023)
Six-Gun w/ iQ (P/N 63749)
EconoMind w/ switch (P/N 63743-
63745)
EconoMind w/ iQ (P/N 63747-63748)
- Adds power safely to your vehicle
- Engine and transmission safeguards
- Change power levels on-the-fly
Thermocouple
- Add a temperature limiting function
to your Diesel Tuner
AutoMind Programmer
(P/N 66100)
- Contains Banks tunes that boost
your vehicles HP, Torque and MPG.
- Displays a host of critical engine
functions
- Provides “service technician”
diagnostic capabilities
- Has upgradeable functionality, so it
will never be out of date
Banks Stinger Systems
(P/N 46465-46486)
Contains:
- Ram-Air Intake system
- Monster Exhaust (single or dual)
- EconoMind Tuner w/ Banks iQ
Banks PowerPack Systems
(P/N 46497-46519)
Contains:
- Ram-Air Intake system
- Monster Exhaust (single or dual)
- EconoMind Tuner w/ Banks iQ
- High-Ram
- Techni-Cooler System
Banks Six-Gun Bundle
(P/N 46594-46613)
Contains:
- Ram-Air Intake system
- Monster Exhaust (single or dual)
- Six-Gun Tuner w/ Banks iQ
Banks Big Hoss Bundle
(P/N 46623-46643)
Contains:
- Ram-Air Intake system
- Monster Exhaust (single or dual)
- Six-Gun Tuner w/ Banks iQ
- Big Head Wastegate Actuator
- High-Ram
- Techni-Cooler System

496808 v.14 .0
Disclaimer of Liability
Gale Banks Engineering Inc., and its
distributors, employees, and dealers
(hereafter “SELLER”) shall in no way be
responsible for the product’s proper use
and service. The BUYER hereby waives
all liability claims.
The BUYER acknowledges that he/
she is not relying on the SELLER’s skill
or judgment to select or furnish goods
suitable for any particular purpose
and that there are no liabilities which
extended beyond the description
on the face hereof and the BUYER
hereby waives all remedies or liabilities,
expressed or implied, arising by law
or otherwise, (including without
any obligations of the SELLER with
respect to fitness, merchantability, and
consequential damages) whether or not
occasioned by the SELLER’s negligence.
The BUYER is responsible to fully
understand the capability and limitations
of his/her vehicle according to
manufacturer specifications and agrees
to hold the SELLER harmless from any
damage resulting from the failure to
adhere to such specifications.
The SELLER disclaims any warranty
and expressly disclaims any liability
for personal injury or damages. The
BUYER acknowledges and agrees
that the disclaimer of any liability for
personal injury is a material term for
this agreement and the BUYER agrees
to indemnify the SELLER and to hold
the SELLER harmless from any claim
related to the item of the equipment
purchased. Under no circumstances will
the SELLER be liable for any damages
or expenses by reason of the use or
sale of any such equipment.
The BUYER is responsible to obey
all applicable federal, state, and
local laws, statutes, and ordinances
when operating his/her vehicle, and
the BUYER agrees to hold SELLER
harmless from any violation thereof.
The SELLER assumes no liability
regarding the improper installation
or misapplication of its products. It is
the installer’s responsibility to check
for proper installation and if in doubt,
contact the manufacturer.
The BUYER is solely responsible for all
warranty issues from the automotive
manufacturer.
Limitation of Warranty
Gale Banks Engineering Inc. (hereafter
“SELLER”), gives Limited Warranty as
to description, quality, merchantability,
fitness for any particular purpose,
productiveness, or any other matter of
SELLER’s product sold herewith. The
SELLER shall be in no way responsible
for the product’s open use and service
and the BUYER hereby waives all rights
except those expressly written herein.
This Warranty shall not be extended
or varied except by written instrument
signed by SELLER and BUYER.
Please see enclosed warranty
information card, for warranty
information regarding your product. All
products that are in question of
Warranty must be returned shipping
prepaid to the SELLER and
THIS IS A HIGH PERFORMANCE
PRODUCT. USE AT YOUR OWN
RISK.
Do not use this product until
you have carefully read the
following agreement.
This sets forth the terms and
conditions for the use of this
product. The installation of
this product indicates that
the BUYER has read and
understands this agreement
and accepts its terms and
conditions.

96808 v.14.0 5
must be accompanied by a dated proof
of purchase receipt. All Warranty claims
are subject to approval by Gale Banks
Engineering Inc.
Under no circumstance shall the SELLER
be liable for any labor charged or travel
time incurred in diagnosis for defects,
removal, or reinstallation of this product,
or any other contingent expense.
WARNING: Below 32oF (0oC)
or above 140oF (60oC), the
Banks iQ may be susceptible
to damage as a result of
extended direct exposure to
sunlight, heat or extreme cold.
It is highly recommended that
Banks iQ be removed from
its mounting location if the
vehicle will be subjected to high
concentrations of sunlight, heat
or cold for an extended period
of time. Gale Banks Engineering
is not responsible for damage
to Banks iQ resulting from
exposure conditions.
Under no circumstances will the SELLER
be liable for any damage or expenses
incurred by reason of the use or sale of
any such equipment.
In the event that the buyer does
not agree with this agreement:
The buyer may promptly return
this product, in a new and
unused condition, with a dated
proof-of-purchase, to the place-
of-purchase within thirty (30)
days from date-of-purchase for a
full refund, less shipping and/or
restocking fee.
The installation of this product
indicates that the buyer has
read and understands this
agreement and accepts its
terms and conditions.
Table of Contents
General Installation Practices ....7
Section 1 ......................8
Installation of Wiring Harness and
Connections for Six-Gun/EconoMind
Diesel Tuner
Section 2 .....................18
Installation of Wiring Harness and
Connections for Optional Banks Brake
Section 3 .....................25
Installation of the Banks Six-Gun/
EconoMind/Brake Selector Switch &
Speed-Loader Module
Section 4 .....................30
Optional Thermocouple Installation
Section 5 .....................32
Banks Brake Operation
Section 6 .....................34
Automatic Transmission Learning
(Required for Six-Gun/EconoMind Only)
Section 7 .....................35
Checking Engine Performance
Section 8 .....................35
Clearing Learned Information
Section 9 .....................36
Troubleshooting
Section 10 ....................39
Removal of the Six-Gun/EconoMind
Diesel Tuner
Section 11 ....................40
Placement of the Banks Power Decals

696808 v.14 .0
The Banks Six-Gun/EconoMind Diesel
Tuner has six power levels that you can
adjust with the Banks iQ Dashboard PC.
Banks iQ is a versatile device that gives
you total control of your Banks Six-
Gun/EconoMind Tuner. With a touch of
your finger on the bright, full-color LCD
display, you can adjust power levels
on-the-fly, customize the gauges you
view, tune numerous performance
parameters, set system warnings
and alerts, see vital engine functions
at a glance, and more. Evaluate your
changes by running 0-60, ¼ and 1/8
mile performance tests. You can even
scan, read and clear OBDII diagnostic
trouble codes.
Banks iQ doesn’t stop there. It’s a true
in-car PC packed full of extra functions.
Listen to your favorite tunes, watch
videos, play games, review Windows®
Office documents, and more.
Expandable and upgradeable, it comes
fitted with a rechargeable battery and
includes accessory cords. You’ll quickly
discover Banks iQ is the device you’ll
use every day, both inside and outside
your car.
Each additional higher level adds
approximately 20% of the available
power increase. To prevent damage
to the factory transmission, Banks
recommends that both automatic and
manual transmission vehicles do not
exceed Level 4 while the vehicle is
experiencing load (towing, climbing a
steep grade, carrying a load, etc.).
To use the higher levels of the
Six-Gun/EconoMind Diesel Tuner
while towing or climbing, airflow
improvements must be made to lower
the exhaust gas temperature (EGT)
entering the turbo. The EGT should not
exceed 1400º F for more than a few
seconds. Elevated EGT can damage
the turbocharger and the engine.
ATTENTION!
Before proceeding with these
instructions, please carefully read
the DISCLAIMER OF LIABILITY
and LIMITATION OF WARRANTY
statement located on page 4 of
this manual.
WARNING: Banks iQ may be
susceptible to damage as a result
of extended exposure to sunlight,
heat or extreme cold. It is highly
recommended that Banks iQ
be removed from its mounting
location if the vehicle will be
subjected to high concentrations
of sunlight, heat or cold for
an extended period of time.
Gale Banks Engineering is not
responsible for damage to Banks iQ
resulting from exposure conditions.

96808 v.14.0 7
TOOLS REQUIRED:
• Inch and metric sockets
• Inch and metric combination and
open-end wrenches
• Pliers
• Ford stereo removal tool
(’03-04 model year vehicles only)
• Wire cutters
• Scissors
• Drill motor
•1⁄8” drill bit
•13⁄32” drill bit
•7⁄16” drill bit
• Tap handle
•1⁄4” NPT tap
• Foot-pound torque wrenches
• Penetrating oil or light lubricant spray
• Anti-seize compound
• Heat gun
1. Before starting work, familiarize
yourself with the installation procedure
by reading all of the instructions.
2. The exploded views provide only
general guidance. Refer to each step
and section diagram in this manual for
proper instruction.
3. Throughout this manual, the left side
of the vehicle refers to the driver side,
and the right side to the passenger side.
4. Disconnect the negative (ground)
cable from the battery (or batteries, if
there are two) before beginning work.
5. Route and tie wires and hoses a
minimum of 6” away from exhaust
heat, moving parts and sharp
edges. Clearance of 8” or more is
recommended where possible.
6. When raising the vehicle, support it
on properly weight-rated safety stands,
ramps or a commercial hoist.
Follow the manufacturer’s safety
precautions. Take care to balance the
vehicle to prevent it from slipping or
falling. When using ramps, be sure the
front wheels are centered squarely on
the topsides. When raising the front
of the vehicle, put the transmission in
park (automatic) or reverse (manual),
set the parking brake, and block the
rear wheels. When raising the back of
the vehicle, be sure the vehicle is on
level ground and the front wheels are
blocked securely.
CAUTION: Do not use floor jacks to
support the vehicle while working
under it. Do not raise the vehicle
onto concrete blocks, masonry
or any other item not intended
specifically for this use.
7. During installation, keep the work
area clean. Do not allow anything to
be dropped into intake, exhaust, or
lubrication system components while
performing the installation, as foreign
objects will cause immediate engine
damage upon start-up.
8. Save this Owner’s Manual as a
reference for system maintenance and
service.
9. Banks recommends either a Banks
IQ or a Pyrometer (EGT) gauge and
Boost gauge be installed with the Six-
Gun/EconoMind Diesel Tuner to help
monitor performance and exhaust gas
temperature of the vehicle (see part
numbers next page). To further increase
engine life by lower EGT’s, Banks also
recommends installing a Monster
Exhaust®system (see next page).
General Installation Practices

896808 v.14 .0
If Six-Gun has been previously
installed, skip to Section 2.
1. Disconnect the battery ground
cables from each of the batteries.
Secure the cables so that they do not
come in contact with the battery posts
during the installation.
2. Remove the (+) battery cable from
the driver side battery.
3. Remove the driver side plastic
battery cover, as shown in Figure 2.
This is accomplished by depressing a
tab at the front and rear of the cover.
Be careful not to damage the cover, as
it will be re-installed.
4. Remove the driver side battery hold
down clamp (8mm socket). Remove
the driver side battery.
WARNING: When lifting a battery,
excessive pressure on the end
walls could cause acid to spew
through the vent caps, resulting in
personal injury. Lift with a battery
carrier or with hands on opposite
corners. Failure to follow these
instructions may result in personal
injury.
Section 1
INSTALLATION OF WIRING HARNESS & CONNECTIONS FOR SIX-GUN/
ECONOMIND DIESEL TUNER
Banks iQ System .....................61152
Banks Monster®Exhaust:
‘03 F-250/350 Pickup
Ext cab, short bed.......................48764
‘04-07 F-250/350 Pickup
Ext cab, short bed.......................48784
‘03 F-250/350 Pickup
Ext cab, long bed ........................48766
‘04-07 F-250/350 Pickup
Ext cab, long bed ........................48786
‘03 F-250/350 Pickup
Crew cab, short bed ...................48765
‘04-07 F-250/350 Pickup
Crew cab, short bed ...................48785
‘03 F-250/350 Pickup
Crew cab, long bed.....................48767
‘04-07 F-250/350 Pickup
Crew cab, long bed ....................48787
‘03 Excursion...............................48768
‘04-07 Excursion .........................48788
Additional Equipment:
TechniCooler®(‘03-04).....................25974
TechniCooler®(‘05-07).....................25975
Gauge Assembly,
Boost and Pyro ...........................64507
Thermocouple ............................63055

96808 v.14.0 9
General Assembly: Six-Gun/EconoMind and supplied wiring harnesses
(Six-Gun shown)
Figure 2: Removal of the battery box cover

10 96808 v.14 .0
Figure 3: Six-Gun/EconoMind Diesel Tuner installed on the inner fender
(2003-04 model year vehicles only) (Six-Gun Shown)
5. Place the Six-Gun/EconoMind Diesel
Tuner in close proximity as shown in
Figure 3 for 2003-04 and Figure 4 for
2005-07. The ‘In-Cab Cable’ with the
three small connectors will be routed
into the cabin via the grommet on the
firewall. The MAP sensor harness with
the two connectors will be routed via
the firewall to its prospective location
listed in the following steps.
NOTE: (The Six-Gun/EconoMind Diesel
Tuner will be affixed to its permanent
location in step 20.)
6. Locate the Powertrain Control
Module (PCM) on the driver side of
the vehicle engine compartment (see
Figure 5).
7. Disconnect the middle connector
from the PCM by opening the
overcenter retaining clamp as shown
in Figure 5. Route the disconnected
PCM connector to the Six-Gun/
EconoMind Diesel Tuner as directed
below:
2003-04 model year vehicles: Route
the previously disconnected middle
connector under the power steering
fluid reservoir towards the Six-Gun/
EconoMind Diesel Tuner.
2005-07 model year vehicles: Route
the previously disconnected middle
connector in the most direct path
towards the Six-Gun/EconoMind Diesel
Tuner.
8. All Years: Plug the PCM connector
into the connector on the Six-Gun/
EconoMind Diesel Tuner labeled,
”VEHICLE HARNESS”.
9. Locate the supplied ‘Crossover
Cable’ wiring harness in your Six-Gun/
EconoMind tuner kit.
10. Plug the supplied ‘Crossover
Cable’ wiring harness into the Six-Gun/
EconoMind Diesel Tuner connector
labeled, “BANKS HARNESS.”
For 2005-2007 Model vehicles: Slide
Six-Gun/EconoMind Shield onto
crossover cable.

96808 v.14.0 11
Figure 4: Six-Gun/EconoMind installed on the fuse box on 2005-07 model-year vehicles
Figure 5: View of the PCM after the battery cover has been removed

12 96808 v.14 .0
Figure 6: (2005-07 model year vehicles only) Tuner Mounting
NOTE: Be sure that the seam on the
top of the shield is facing away from
the cabin (see Figure 6).
For all models, route the other end of
the ‘Crossover Cable’ to the vehicle’s
PCM middle connector labeled “C”.
Route the ‘Crossover Cable’ as directed
below:
2003-04 model year vehicles: Route
the ‘Crossover Cable’ under the power
steering fluid reservoir.
2005-07 model year vehicles: Route the
‘Crossover Cable’ to the PCM in the
most direct path possible.
11. All Years: Plug the ‘Crossover
Cable’ into the vehicle’s PCM middle
connector labeled “C”.
12. Unplug the Manifold Absolute
Pressure (MAP) sensor connector
shown in Figure 7. The MAP connector
can be unplugged by sliding the red
safety slide down, pressing the locking
button, then pulling on the connector.
13. Plug the Six-Gun/EconoMind
MAP connector into the MAP sensor.
Plug the factory MAP connector into
the Six-Gun/EconoMind MAP wiring
harness. Route the harness from the
Six-Gun/EconoMind to the MAP sensor
as shown in Figure 8. Use the supplied
zip ties to secure the MAP harness
to the factory harness. Failure to
follow the recommended harness
routing may result in a melted
harness.
14. Route the Six-Gun/EconoMind
‘In-Cab Cable’ through the firewall to
the passenger compartment. When
passing through the firewall, either
make a hole in a factory grommet or
drill a hole and use a new grommet.
If drilling, check the backside to make
sure there are no components that
may be damaged by drilling.
15. Remove the lower driver side
interior panel that allows access to the
fuse box.

96808 v.14.0 13
Figure 7: MAP sensor location
Figure 8: MAP sensor harness routing

14 96808 v.14 .0
Figure 9: OBDII interface cable
16. From inside the vehicle, continue
to pull the cable through the firewall
until it is approximately 22” inside the
cab. Secure the cable to the lower
access panel area. Take precaution to
leave the three connectors accessible
for usage further in the installation
process.
If only installing Banks Six-Gun/
EconoMind continue to step 17.
If Banks Brake is being installed, skip
to step 20.
17. Locate the ‘OBDII Interface
Cable’ in your kit. Connect the ‘OBDII
Interface Cable’ to the vehicle OBDII
connector. Use the large cable tie
in your kit as shown in Figure 9 to
secure the ‘OBDII Interface Cable’ to
the vehicle OBDII connector. Now,
connect the 8-pin connector from the
‘OBDII Interface Cable’ to the 8-pin
connector on the Six-Gun/EconoMind
‘In-Cab Cable.’ Note: If you are not
installing the optional Banks iQ then
coil up and secure cable with the RJ12
(telephone style) connector end.
18. Remove the fuse box cover,
located in the cabin compartment.
Locate the mini-fuse #22 and remove.
Install the mini-auto blade fuse tap
onto the removed mini fuse as shown
in Figure 10. Re-install the mini fuse
with the attached blade tap into
location #22 as shown in Figure 11.
19. Locate the RED single terminal
connector on the ‘OBDII Interface
Cable’ and connect it to the mini-fuse
blade tap location #22. Replace the
fuse cover and make sure not to pinch
the RED single terminal wire.

96808 v.14.0 15
Figure 10: Mini-auto blade fuse tap
Figure 11

16 96808 v.14 .0
Mounting The Six-Gun/EconoMind
Diesel Tuner
20. 2003-04 model year vehicles only:
Remove the clip shown in Figure 12
to create adequate room to mount the
Six-Gun/EconoMind Diesel Tuner to the
driver side inner fender.
21. 2003-04 four-wheel drive
vehicles: The module shown in Figure
13 will appear only in four-wheel-
drive vehicles. This may need to be
relocated to make room for the Six-
Gun/EconoMind Diesel Tuner. The
mounting location of this module by
the factory has not been consistent on
early vehicles.
NOTE: Make sure all mounting surfaces
are entirely clean and free of dirt
and oil before mounting the Six-Gun/
EconoMind Diesel Tuner. Clean and
dry as required using a cloth damped
in rubbing alcohol or similar cleaning
solution.
21. 2005-07 model year vehicles only:
Remove the adhesive backing from two
(2) dual-lock fasteners and attach them
to the Six-Gun/EconoMind shield and
the top of the fuse box.
22. Remove the adhesive backing
from the (2) dual-lock fasteners on the
back of the Six-Gun/EconoMind Diesel
Tuner and affix the tuner to:
2003-04 model year vehicles: The inner
driver side fender as shown in Figure 3
Note: Shield will not be used for
installations on 03-04 models. Shield
will only be used on 05-07 models.
2005-07 model year vehicles: The inside
roof of the Six-Gun/EconoMind shield,
that is mounted on the fuse box cover
as shown in Figure 4 & 6.
WARNING: The use of Banks Brake
is for use with installed Six-Gun/
EconoMind Tuner Package with
power level selector switch only.
-END, SECTION 1-

96808 v.14.0 17
Figure 13
Figure 12: Removal of hood latch cable clip (2003-04 model year vehicles only)

18 96808 v.14 .0
General Assembly: Banks Brake Wire Harnesses
If not installing Banks Brake, continue
to Section 3.
If an existing Six-Gun/EconoMind
Tuner has been previously
installed, verify that the Tuner has
the latest version firmware. Check
and compare to the current version
available on the Banks website.
Banks Brake may not function
properly if Six-Gun/EconoMind
Tuner firmware is not up to the
current version.
1. Remove the fuse access panel
below the steering column as shown in
Figure 14.
2. Remove the fuse box cover, located
in the cabin compartment.
If installing a Banks Brake to a
previously installed Banks Six-Gun/
EconoMind Tuner, continue to step 3.
If the Six-Gun/EconoMind is being
installed along with the Banks
Brake, skip to step 7.
Removing a Previously Installed
Banks OBD II Interface Cable
3. Locate the RED single terminal
connector on the Banks ‘OBDII
Interface Cable’ and disconnect it from
the mini-fuse blade tap location #22 if
already connected. DO NOT remove
the mini-fuse blade tap as it will be
used for the Banks Brake wire harness
installation. See Figure 15.
4. Disconnect Banks OBD II interface
cable from the vehicle OBD II
connector.
5. Disconnect the 8-pin connector
from the OBD II interface cable from
the 8-pin connector on the Six-Gun/
EconoMind in-cab cable.
Section 2
INSTALLATION OF WIRING HARNESS & CONNECTIONS FOR
OPTIONAL BANKS BRAKE

96808 v.14.0 19
Figure 15
Figure 14 Ford (’05-’07)

20 96808 v.14 .0
6. Remove the OBD II interface cable
from the vehicle.
Installing Banks Brake Wire
Harness
7. From inside the engine
compartment, locate the factory
brake pressure sensor connector on
the brake master cylinder. The brake
pressure sensor will be the connector
farthest away from the firewall. See
Figure 16. Disconnect the factory
brake pressure sensor connector.
8. Locate the Brake Pressure Sensor
harness in your kit. Connect the
female connector on the Brake
Pressure Sensor harness to the factory
male connector. Connect the male
connector on the Brake Pressure
Sensor harness to the factory female
connector.
9. Route the 2-pin connector on
the Brake Pressure Sensor harness
following the Six-Gun/EconoMind
in-cab cable through the fire wall.
Secure the wiring harness with the
supplied cable ties away from any heat
source or moving parts.
10. From under the dash, pull the
2-pin connector on the Brake Pressure
Sensor harness through the fire wall.
11. Locate the Banks Brake Wire
Harness and connect the 2-pin male
connector on the Brake Pressure
Sensor harness to the 2-pin connector
on the Banks Brake wire harness.
12. Connect the Banks Brake Wire
Harness OBD II connector to the
vehicle’s OBD II connector. Use a cable
tie, as shown in Figure 17 to secure
the Banks Brake Wire Harness to the
vehicle’s OBD II connector.
13. Locate the Fuse connector on the
Banks Brake Wire Harness and connect
it to the mini-fuse blade tap location
#22. Replace the fuse cover and make
sure not to pinch the Fuse wire.
14. Now, connect the 8-pin connector
from the Banks Brake Wire Harness to
the 8-pin connector on the Six-Gun/
EconoMind In-Cab Cable.
15. Locate the Foot Brake position
switch connector under the dash.
See Figure 18. Disconnect the foot
brake position switch connector.
Figure 16 Brake Pressure Sensor