iDataLink maestro Rr User manual

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in
are the properties of their respective owners.
WARNING
Pressing the printer icon or “quick printing” this document will print
all of the guides in this compilation.
Open the Bookmarks menu and find your vehicle OR scroll
down until you find the install guide for your vehicle.
Print only the pages for your vehicle using the advanced
options in the Print menu.
Install your Maestro RR according to the guide for your vehicle.
HOW TO USE THIS INSTALL GUIDE
1
2
3
SELECT VEHICLE
PRINT PAGES NEEDED

OPTIONAL ACCESSORIES
None
PROGRAMMED FIRMWARE
ADS-RR(SR)-CHR02-AS
PRODUCTS REQUIRED
iDatalink Maestro RR Radio Replacement Interface
iDatalink Maestro CH2 Installation Harness
INSTALL GUIDE
CHRYSLER 300
BASE 20052007
retains steering wheel controls and more!
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here
in are the properties of their respective owners.

ADS-RR(SR)-CHR02-AS maestro.idatalink.com
chrysler 300 Base 2005-2007
Automotive Data Solutions Inc. © 2017 2
WELCOME
NEED HELP?
Congratulations on the purchase
of your iDatalink Maestro RR Radio
replacement solution. You are
now a few simple steps away from
enjoying your new car radio with
enhanced features.
Before starting your installation,
please ensure that your iDatalink
Maestro module is programmed
with the correct firmware for your
vehicle as per the Getting Started
section, and that you carefully
review the Installation Diagram and
Vehicle Wire Reference Chart.
Please note that Maestro RR will
only retain functionalities that
were originally available in the
vehicle.
1 866 427-2999
[email protected]
maestro.idatalink.com/support
www.12voltdata.com/forum
DURING INSTALLATION
Installation Instructions 3
Wiring Diagram 4

ADS-RR(SR)-CHR02-AS maestro.idatalink.com
chrysler 300 Base 2005-2007
Automotive Data Solutions Inc. © 2017 3
INSTALLATION INSTRUCTIONS
STEP 1
• Remove the factory radio.
• Access the main 22 pin factory radio connector (2.1) and
determine if you have a factory amplifier.
If you have wires in PIN 7, 8, 9 and 10, you don’t have a
factory amplifier.
If you don’t have wires in PIN 7, 8, 9 and 10, you have a
factory amplifier.
• Unbox the aftermarket radio and locate its main harness.
• Connect the wires shown on the next page from
aftermarket radio main harness to the CH2 T-harness and
match the wire functions.
STEP 2
If the vehicle DOES have a factory amplifier:
• Plug the female BLACK connector to the male WHITE
connector of your CH2 T-harness.
• Plug the female WHITE connector to the male BLACK
connector of your CH2 T-harness.
If the vehicle DOES NOT have a factory amplifier:
• Plug the female BLACK connector to the male BLACK
connector of your CH2 T-harness.
• Plug the female WHITE connector to the male WHITE
connector of your CH2 T-harness.
STEP 3
• Connect the factory harness to the CH2 T-harness.
STEP 4
• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Plug the Steering Wheel Control cable to the aftermarket
radio.
STEP 5
• Connect all the harnesses to the Maestro RR module then
proceed to module setup.
The module is now ready to be used.
Insert the aftermarket radio in the dashboard housing and
test all the functionalities.
Reassemble the dashboard carefully.
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key
to the OFF position then disconnect all connectors from
the module. Press and hold the module’s programming
button and connect all the connectors back to the module.
Wait, the module’s LED will flash RED rapidly (this may
take up to 10 seconds). Release the programming button.
Wait, the LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail
“[email protected]”. Visit us at “maestro.idatalink.
com/support” and “www.12voltdata.com/forum/”
1
Fig. 2.1
45671121 3
15 16 17 18
8 9 10
19 20 21 221312 14

ADS-RR(SR)-CHR02-AS maestro.idatalink.com
chrysler 300 Base 2005-2007
Automotive Data Solutions Inc. © 2017 4
C
AF
G
C
A
G
F
1
E
E
WIRING DIAGRAM
STEP 1
STEP 2
STEP 3
STEP 4
STEP 5
MAESTRO RR MODULE
WHITE - LF SPEAKER (+)
WHITE/BLACK - LF SPEAKER (-)
GRAY - RF SPEAKER (+)
GRAY/BLACK - RF SPEAKER (-)
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE/BLACK - RR SPEAKER (-)
YELLOW - 12V (+)
BLACK - GROUND
RED - ACCESSORY (+)
BROWN (NOT CONNECTED)
WHITE
WHITE
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
BLUE/WHITE - AMP. TURN ON (+)
MAIN
HARNESS
PURPLE - RR SPEAKER (+)
CH2 T-HARNESS
FACTORY RADIO
HARNESS
WIRES FROM
VEHICLE
PINK - VEHICLE SPEED (CONNECT IF THERE IS A MATCH)
WHITEWHITE
BLACKBLACK
BLACK
BLACK
CONNECT TO
AFTERMARKET RADIO
STEERING WHEEL
CONTROL CABLE
CONNECTION NOT REQUIRED
N.C.
CONNECTIONS WITH AMP
CONNECTIONS WITHOUT AMP

OPTIONAL ACCESSORIES
None
PROGRAMMED FIRMWARE
ADS-RR(SR)-CHR02-AS
PRODUCTS REQUIRED
iDatalink Maestro RR Radio Replacement Interface
iDatalink Maestro CH2 Installation Harness
INSTALL GUIDE
CHRYSLER PT CRUISER
BASE 20062010
retains steering wheel controls and more!
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here
in are the properties of their respective owners.

ADS-RR(SR)-CHR02-AS maestro.idatalink.com
chrysler Pt cruiser Base 2006-2010
Automotive Data Solutions Inc. © 2017 2
WELCOME
NEED HELP?
Congratulations on the purchase
of your iDatalink Maestro RR Radio
replacement solution. You are
now a few simple steps away from
enjoying your new car radio with
enhanced features.
Before starting your installation,
please ensure that your iDatalink
Maestro module is programmed
with the correct firmware for your
vehicle as per the Getting Started
section, and that you carefully
review the Installation Diagram and
Vehicle Wire Reference Chart.
Please note that Maestro RR will
only retain functionalities that
were originally available in the
vehicle.
1 866 427-2999
[email protected]
maestro.idatalink.com/support
www.12voltdata.com/forum
DURING INSTALLATION
Installation Instructions 3
Wiring Diagram 4

ADS-RR(SR)-CHR02-AS maestro.idatalink.com
chrysler Pt cruiser Base 2006-2010
Automotive Data Solutions Inc. © 2017 3
INSTALLATION INSTRUCTIONS
STEP 1
• Remove the factory radio.
• Access the main 22 pin factory radio connector (2.1) and
determine if you have a factory amplifier.
If you have wires in PIN 7, 8, 9 and 10, you don’t have a
factory amplifier.
If you don’t have wires in PIN 7, 8, 9 and 10, you have a
factory amplifier.
• Unbox the aftermarket radio and locate its main harness.
• Connect the wires shown on the next page from
aftermarket radio main harness to the CH2 T-harness and
match the wire functions.
STEP 2
If the vehicle DOES have a factory amplifier:
• Plug the female BLACK connector to the male WHITE
connector of your CH2 T-harness.
• Plug the female WHITE connector to the male BLACK
connector of your CH2 T-harness.
If the vehicle DOES NOT have a factory amplifier:
• Plug the female BLACK connector to the male BLACK
connector of your CH2 T-harness.
• Plug the female WHITE connector to the male WHITE
connector of your CH2 T-harness.
STEP 3
• Connect the factory harness to the CH2 T-harness.
STEP 4
• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Plug the Steering Wheel Control cable to the aftermarket
radio.
STEP 5
• Connect all the harnesses to the Maestro RR module then
proceed to module setup.
The module is now ready to be used.
Insert the aftermarket radio in the dashboard housing and
test all the functionalities.
Reassemble the dashboard carefully.
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key
to the OFF position then disconnect all connectors from
the module. Press and hold the module’s programming
button and connect all the connectors back to the module.
Wait, the module’s LED will flash RED rapidly (this may
take up to 10 seconds). Release the programming button.
Wait, the LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail
“[email protected]”. Visit us at “maestro.idatalink.
com/support” and “www.12voltdata.com/forum/”
1
Fig. 2.1
45671121 3
15 16 17 18
8 9 10
19 20 21 221312 14

ADS-RR(SR)-CHR02-AS maestro.idatalink.com
chrysler Pt cruiser Base 2006-2010
Automotive Data Solutions Inc. © 2017 4
C
AF
G
C
A
G
F
1
E
E
WIRING DIAGRAM
STEP 1
STEP 2
STEP 3
STEP 4
STEP 5
MAESTRO RR MODULE
WHITE - LF SPEAKER (+)
WHITE/BLACK - LF SPEAKER (-)
GRAY - RF SPEAKER (+)
GRAY/BLACK - RF SPEAKER (-)
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE/BLACK - RR SPEAKER (-)
YELLOW - 12V (+)
BLACK - GROUND
RED - ACCESSORY (+)
BROWN (NOT CONNECTED)
WHITE
WHITE
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
BLUE/WHITE - AMP. TURN ON (+)
MAIN
HARNESS
PURPLE - RR SPEAKER (+)
CH2 T-HARNESS
FACTORY RADIO
HARNESS
WIRES FROM
VEHICLE
PINK - VEHICLE SPEED (CONNECT IF THERE IS A MATCH)
WHITEWHITE
BLACKBLACK
BLACK
BLACK
CONNECT TO
AFTERMARKET RADIO
STEERING WHEEL
CONTROL CABLE
CONNECTION NOT REQUIRED
N.C.
CONNECTIONS WITH AMP
CONNECTIONS WITHOUT AMP

OPTIONAL ACCESSORIES
None
PROGRAMMED FIRMWARE
ADS-RR(SR)-CHR02-AS
PRODUCTS REQUIRED
iDatalink Maestro RR Radio Replacement Interface
iDatalink Maestro CH2 Installation Harness
INSTALL GUIDE
DODGE CALIBER
BASE 20072008
retains steering wheel controls and more!
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here
in are the properties of their respective owners.

ADS-RR(SR)-CHR02-AS maestro.idatalink.com
dodge caliBer Base 2007-2008
Automotive Data Solutions Inc. © 2017 2
WELCOME
NEED HELP?
Congratulations on the purchase
of your iDatalink Maestro RR Radio
replacement solution. You are
now a few simple steps away from
enjoying your new car radio with
enhanced features.
Before starting your installation,
please ensure that your iDatalink
Maestro module is programmed
with the correct firmware for your
vehicle as per the Getting Started
section, and that you carefully
review the Installation Diagram and
Vehicle Wire Reference Chart.
Please note that Maestro RR will
only retain functionalities that
were originally available in the
vehicle.
1 866 427-2999
[email protected]
maestro.idatalink.com/support
www.12voltdata.com/forum
DURING INSTALLATION
Installation Instructions 3
Wiring Diagram 4

ADS-RR(SR)-CHR02-AS maestro.idatalink.com
dodge caliBer Base 2007-2008
Automotive Data Solutions Inc. © 2017 3
INSTALLATION INSTRUCTIONS
STEP 1
• Remove the factory radio.
• Access the main 22 pin factory radio connector (2.1) and
determine if you have a factory amplifier.
If you have wires in PIN 7, 8, 9 and 10, you don’t have a
factory amplifier.
If you don’t have wires in PIN 7, 8, 9 and 10, you have a
factory amplifier.
• Unbox the aftermarket radio and locate its main harness.
• Connect the wires shown on the next page from
aftermarket radio main harness to the CH2 T-harness and
match the wire functions.
STEP 2
If the vehicle DOES have a factory amplifier:
• Plug the female BLACK connector to the male WHITE
connector of your CH2 T-harness.
• Plug the female WHITE connector to the male BLACK
connector of your CH2 T-harness.
If the vehicle DOES NOT have a factory amplifier:
• Plug the female BLACK connector to the male BLACK
connector of your CH2 T-harness.
• Plug the female WHITE connector to the male WHITE
connector of your CH2 T-harness.
STEP 3
• Connect the factory harness to the CH2 T-harness.
STEP 4
• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Plug the Steering Wheel Control cable to the aftermarket
radio.
STEP 5
• Connect all the harnesses to the Maestro RR module then
proceed to module setup.
The module is now ready to be used.
Insert the aftermarket radio in the dashboard housing and
test all the functionalities.
Reassemble the dashboard carefully.
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key
to the OFF position then disconnect all connectors from
the module. Press and hold the module’s programming
button and connect all the connectors back to the module.
Wait, the module’s LED will flash RED rapidly (this may
take up to 10 seconds). Release the programming button.
Wait, the LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail
“[email protected]”. Visit us at “maestro.idatalink.
com/support” and “www.12voltdata.com/forum/”
1
Fig. 2.1
45671121 3
15 16 17 18
8 9 10
19 20 21 221312 14

ADS-RR(SR)-CHR02-AS maestro.idatalink.com
dodge caliBer Base 2007-2008
Automotive Data Solutions Inc. © 2017 4
C
AF
G
C
A
G
F
1
E
E
WIRING DIAGRAM
STEP 1
STEP 2
STEP 3
STEP 4
STEP 5
MAESTRO RR MODULE
WHITE - LF SPEAKER (+)
WHITE/BLACK - LF SPEAKER (-)
GRAY - RF SPEAKER (+)
GRAY/BLACK - RF SPEAKER (-)
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE/BLACK - RR SPEAKER (-)
YELLOW - 12V (+)
BLACK - GROUND
RED - ACCESSORY (+)
BROWN (NOT CONNECTED)
WHITE
WHITE
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
BLUE/WHITE - AMP. TURN ON (+)
MAIN
HARNESS
PURPLE - RR SPEAKER (+)
CH2 T-HARNESS
FACTORY RADIO
HARNESS
WIRES FROM
VEHICLE
PINK - VEHICLE SPEED (CONNECT IF THERE IS A MATCH)
WHITEWHITE
BLACKBLACK
BLACK
BLACK
CONNECT TO
AFTERMARKET RADIO
STEERING WHEEL
CONTROL CABLE
CONNECTION NOT REQUIRED
N.C.
CONNECTIONS WITH AMP
CONNECTIONS WITHOUT AMP

OPTIONAL ACCESSORIES
None
PROGRAMMED FIRMWARE
ADS-RR(SR)-CHR02-AS
PRODUCTS REQUIRED
iDatalink Maestro RR Radio Replacement Interface
iDatalink Maestro CH2 Installation Harness
INSTALL GUIDE
DODGE CHARGER
BASE 20062007
retains steering wheel controls and more!
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here
in are the properties of their respective owners.

ADS-RR(SR)-CHR02-AS maestro.idatalink.com
dodge charger Base 2006-2007
Automotive Data Solutions Inc. © 2017 2
WELCOME
NEED HELP?
Congratulations on the purchase
of your iDatalink Maestro RR Radio
replacement solution. You are
now a few simple steps away from
enjoying your new car radio with
enhanced features.
Before starting your installation,
please ensure that your iDatalink
Maestro module is programmed
with the correct firmware for your
vehicle as per the Getting Started
section, and that you carefully
review the Installation Diagram and
Vehicle Wire Reference Chart.
Please note that Maestro RR will
only retain functionalities that
were originally available in the
vehicle.
1 866 427-2999
[email protected]
maestro.idatalink.com/support
www.12voltdata.com/forum
DURING INSTALLATION
Installation Instructions 3
Wiring Diagram 4

ADS-RR(SR)-CHR02-AS maestro.idatalink.com
dodge charger Base 2006-2007
Automotive Data Solutions Inc. © 2017 3
INSTALLATION INSTRUCTIONS
STEP 1
• Remove the factory radio.
• Access the main 22 pin factory radio connector (2.1) and
determine if you have a factory amplifier.
If you have wires in PIN 7, 8, 9 and 10, you don’t have a
factory amplifier.
If you don’t have wires in PIN 7, 8, 9 and 10, you have a
factory amplifier.
• Unbox the aftermarket radio and locate its main harness.
• Connect the wires shown on the next page from
aftermarket radio main harness to the CH2 T-harness and
match the wire functions.
STEP 2
If the vehicle DOES have a factory amplifier:
• Plug the female BLACK connector to the male WHITE
connector of your CH2 T-harness.
• Plug the female WHITE connector to the male BLACK
connector of your CH2 T-harness.
If the vehicle DOES NOT have a factory amplifier:
• Plug the female BLACK connector to the male BLACK
connector of your CH2 T-harness.
• Plug the female WHITE connector to the male WHITE
connector of your CH2 T-harness.
STEP 3
• Connect the factory harness to the CH2 T-harness.
STEP 4
• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Plug the Steering Wheel Control cable to the aftermarket
radio.
STEP 5
• Connect all the harnesses to the Maestro RR module then
proceed to module setup.
The module is now ready to be used.
Insert the aftermarket radio in the dashboard housing and
test all the functionalities.
Reassemble the dashboard carefully.
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key
to the OFF position then disconnect all connectors from
the module. Press and hold the module’s programming
button and connect all the connectors back to the module.
Wait, the module’s LED will flash RED rapidly (this may
take up to 10 seconds). Release the programming button.
Wait, the LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail
“[email protected]”. Visit us at “maestro.idatalink.
com/support” and “www.12voltdata.com/forum/”
1
Fig. 2.1
45671121 3
15 16 17 18
8 9 10
19 20 21 221312 14

ADS-RR(SR)-CHR02-AS maestro.idatalink.com
dodge charger Base 2006-2007
Automotive Data Solutions Inc. © 2017 4
C
AF
G
C
A
G
F
1
E
E
WIRING DIAGRAM
STEP 1
STEP 2
STEP 3
STEP 4
STEP 5
MAESTRO RR MODULE
WHITE - LF SPEAKER (+)
WHITE/BLACK - LF SPEAKER (-)
GRAY - RF SPEAKER (+)
GRAY/BLACK - RF SPEAKER (-)
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE/BLACK - RR SPEAKER (-)
YELLOW - 12V (+)
BLACK - GROUND
RED - ACCESSORY (+)
BROWN (NOT CONNECTED)
WHITE
WHITE
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
BLUE/WHITE - AMP. TURN ON (+)
MAIN
HARNESS
PURPLE - RR SPEAKER (+)
CH2 T-HARNESS
FACTORY RADIO
HARNESS
WIRES FROM
VEHICLE
PINK - VEHICLE SPEED (CONNECT IF THERE IS A MATCH)
WHITEWHITE
BLACKBLACK
BLACK
BLACK
CONNECT TO
AFTERMARKET RADIO
STEERING WHEEL
CONTROL CABLE
CONNECTION NOT REQUIRED
N.C.
CONNECTIONS WITH AMP
CONNECTIONS WITHOUT AMP

OPTIONAL ACCESSORIES
None
PROGRAMMED FIRMWARE
ADS-RR(SR)-CHR02-AS
PRODUCTS REQUIRED
iDatalink Maestro RR Radio Replacement Interface
iDatalink Maestro CH2 Installation Harness
INSTALL GUIDE
DODGE DAKOTA
BASE 20052007
retains steering wheel controls and more!
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here
in are the properties of their respective owners.

ADS-RR(SR)-CHR02-AS maestro.idatalink.com
dodge dakota Base 2005-2007
Automotive Data Solutions Inc. © 2017 2
WELCOME
NEED HELP?
Congratulations on the purchase
of your iDatalink Maestro RR Radio
replacement solution. You are
now a few simple steps away from
enjoying your new car radio with
enhanced features.
Before starting your installation,
please ensure that your iDatalink
Maestro module is programmed
with the correct firmware for your
vehicle as per the Getting Started
section, and that you carefully
review the Installation Diagram and
Vehicle Wire Reference Chart.
Please note that Maestro RR will
only retain functionalities that
were originally available in the
vehicle.
1 866 427-2999
[email protected]
maestro.idatalink.com/support
www.12voltdata.com/forum
DURING INSTALLATION
Installation Instructions 3
Wiring Diagram 4

ADS-RR(SR)-CHR02-AS maestro.idatalink.com
dodge dakota Base 2005-2007
Automotive Data Solutions Inc. © 2017 3
INSTALLATION INSTRUCTIONS
STEP 1
• Remove the factory radio.
• Access the main 22 pin factory radio connector (2.1) and
determine if you have a factory amplifier.
If you have wires in PIN 7, 8, 9 and 10, you don’t have a
factory amplifier.
If you don’t have wires in PIN 7, 8, 9 and 10, you have a
factory amplifier.
• Unbox the aftermarket radio and locate its main harness.
• Connect the wires shown on the next page from
aftermarket radio main harness to the CH2 T-harness and
match the wire functions.
STEP 2
If the vehicle DOES have a factory amplifier:
• Plug the female BLACK connector to the male WHITE
connector of your CH2 T-harness.
• Plug the female WHITE connector to the male BLACK
connector of your CH2 T-harness.
If the vehicle DOES NOT have a factory amplifier:
• Plug the female BLACK connector to the male BLACK
connector of your CH2 T-harness.
• Plug the female WHITE connector to the male WHITE
connector of your CH2 T-harness.
STEP 3
• Connect the factory harness to the CH2 T-harness.
STEP 4
• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Plug the Steering Wheel Control cable to the aftermarket
radio.
STEP 5
• Connect all the harnesses to the Maestro RR module then
proceed to module setup.
The module is now ready to be used.
Insert the aftermarket radio in the dashboard housing and
test all the functionalities.
Reassemble the dashboard carefully.
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key
to the OFF position then disconnect all connectors from
the module. Press and hold the module’s programming
button and connect all the connectors back to the module.
Wait, the module’s LED will flash RED rapidly (this may
take up to 10 seconds). Release the programming button.
Wait, the LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail
“[email protected]”. Visit us at “maestro.idatalink.
com/support” and “www.12voltdata.com/forum/”
1
Fig. 2.1
45671121 3
15 16 17 18
8 9 10
19 20 21 221312 14