Bartec MC 9090ex RFID/LF User manual

English
Mobile Computer
MC 9090ex RFID/LF
MC 9090ex RFID/HF
MC 9090ex RFID/UHF
Type 17-A1.9-R.../H.…...
Document no. 11-A119-7D0003
Status: 4 August 2010
This appendix contains information on the RFID devices.
A further applicable document is the user manual for
the MC 9090ex Mobile Computer for
- ATEX Zone 1 or
- UL Class I, Div 1 and
- UL Class I, II, III Div 1
Appendix A
Supplement for User Manual
ATEX Zone 1
UL Class I Division 1
UL Class I, II, III Division 1

Contents MC 9090ex Mobile Computer
RFID
Technical data subject to change without notice.
Issue 08/2010
1Product Description.............................................................................................................................. 1
2Safety Instructions................................................................................................................................ 2
2.1 Warnings about the Mobile Computers........................................................................................2
2.2 Warnings for Use of Wireless Devices.........................................................................................2
2.2.1 Radio Frequency Interference Requirements - FCC ........................................................2
2.2.2 Radio Frequency Interference Requirements – Canada ..................................................3
2.3 Warnings for screen protection .................................................................................................... 3
3Technical Data....................................................................................................................................... 4
3.1 RFID/LF Internal Module/only UL.................................................................................................4
3.1.1 Explosion Protection .........................................................................................................4
3.1.2 General Data ....................................................................................................................4
3.1.3 Radio Data Transmission RFID/LF (Internal module)........................................................4
3.1.4 Standards supported by firmware ......................................................................................4
3.2 RFID/LF External Module/ATEX and UL......................................................................................5
3.2.1 Explosion Protection.........................................................................................................5
3.2.2 General Data ....................................................................................................................5
3.2.3 Radio Data Transmission RFID/LF (External module)......................................................5
3.2.4 Standards supported by firmware.....................................................................................5
3.3 RFID/HF External Module/ATEX and UL.....................................................................................6
3.3.1 Explosion Protection.........................................................................................................6
3.3.2 General Data ....................................................................................................................6
3.3.3 Radio Data Transmission RFID/HF External Module .......................................................6
3.3.4 Standards supported by Firmware....................................................................................6
3.4 RFID/UHF External Module/ATEX and UL ..................................................................................7
3.4.1 Explosion Protection.........................................................................................................7
3.4.2 General Data ....................................................................................................................7
3.4.3 Radio Data Transmission RFID/UHF External Module.....................................................7
3.5 RFID/UHF External Module + External Antenna..........................................................................8
3.5.1 Explosion Protection.........................................................................................................8
3.5.2 General Data ....................................................................................................................8
3.5.3 Radio Data Transmission RFID/UHF External Module + External Antenna .....................8
3.6 Information on Applied Directives, Standards, Marking and In-Process Inspections ................... 9
3.6.1 Product Marking on Mobile Computer MC 9090ex RFID (UL Class I Division 1)...............9
3.6.2 Product Marking on Mobile Computer MC 9090ex RFID (UL Class I, II, III Division 1).... 11
3.6.3 Product Marking on Mobile Computer MC 9090ex RFID (ATEX Zone 1) ........................13
4Commissioning ................................................................................................................................... 15
4.1 MC 9090ex Manual and Software for Windows Mobile from Motorola........................................ 15
4.2 MC 9090ex RFID Documentation from BARTEC........................................................................15
4.3 MC 9090ex RFID Software .........................................................................................................15
5Additional Information........................................................................................................................ 16
5.1 Order numbers MC 9090ex (ATEX Zone 1)................................................................................16
5.2 Order numbers MC 9090ex (UL Class I Division 1) ....................................................................17
5.3 Order numbers MC 9090ex (UL Class I, II, III Division 1)............................................................18
Appendix - Declaration of Conformity ..................................................................................................19-22

Appendix A
Additional Description MC 9090ex Mobile Computer RFID
Technical data subject to change without notice.
Issue 08/2010 Page 1 of 22
1Product Description
The MC 9090ex RFID mobile computer is a compact portable device and is designed by
BARTEC for use in hazardous areas. Accordingly, the extensive communication
options, already standard in other areas, are available to the user in hazardous areas
also.
The MC 9090ex RFID mobile computer is available in two versions, with pistol grip
(MC 9090ex Gun) and without (MC 9090ex Brick). In these versions, the MC 9090ex is a
compact unit for scanning bar codes and RFID tags reliably.
The scan trigger is ideally positioned on the device, which allows bar codes and RFID
tags to be captured easily. The integrated radio module ensures a real-time exchange
of data with the host system.
The MC 9090ex RFID combines the advantages of the Microsoft Pocket PC Platform
with the strengths of the Intel® XScale™ PXA270 processor with 624 MHz.
The large, easy-to-read 1/4 VGA colour display is equipped with touch screen
technology. The device works with the IEEE802.11 a/b/g (direct sequence) radio
standard.

Appendix A
Additional Description MC 9090ex Mobile Computer RFID
Page 2 of 22 Technical data subject to change without notice.
Issue 08/2010
2
2Safety Instructions
MC 9090ex mobile computer types 17-A119-R ** 6/H *******, type 17-A119-R ** 7 *******
with external RFID/UHF antenna may not be used in processes that generate high
charge levels.
High charge levels can occur in particular with electrostatic painting, pneumatically
conveyed dust, flowing liquids and droplets, mechanically driven belts, brushes and foils
etc.
2.2 Warnings for Use of Wireless Devices
Please observe all warning notices with regard to the usage of wireless devices.
2.2.1 Radio Frequency Interference Requirements - FCC
Note: This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However there is
no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
¨Reorient or relocate the receiving antenna.
¨Increase the separation between the equipment and receiver.
¨Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
¨Consult the dealer or an experienced radio/tv technician for help.
2.1 Warnings about the Mobile Computers

Appendix A
Additional Description MC 9090ex Mobile Computer RFID
Technical data subject to change without notice.
Issue 08/2010 Page 3 of 22
FCC Note according to 15.21
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
Radio Transmitters (Part 15)
This device complies with Part 15 of the FCC rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
2.2.2 Radio Frequency Interference Requirements – Canada
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Radio Transmitters
This device complies with RSS 210 of Industry & Science Canada. Operation is subject
to the following two conditions:
(1) this device may not cause harmful interference and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
Label Marking: The Term "IC:" before the radio certification only signifies that "Industry
Canada" technical specifications were met.
2.3 Warnings for screen protection
The screen protection type 17-A1Z0-0003 of the MC 9090ex Mobile Computer
types 17-A119-H ****/ ******* may be used only in the gas group IIB Ex.

Appendix A
Additional Description MC 9090ex Mobile Computer RFID
Page 4 of 22 Technical data subject to change without notice.
Issue 08/2010
4
3Technical Data
3.1.1 Explosion Protection
Types 17-A129-R*04/H *******
Ex protection type Class I Division 1 Groups C and D
Certification UL file E226123
Types 17-A169-R*04/H *******
Ex protection type Class I Division 1 Groups C and D
Class II Division 1 Groups F and G
Class III Division 1
Certification UL file E226123
3.1.2 General Data
Ambient temperature -20 °C to +40 °C -4 °F to +104 °F
Weight including battery
MC9090ex-K
MC9090ex-G
approx. 700 g approx. 24 oz
approx. 830 g approx. 29 oz
3.1.3 Radio Data Transmission RFID/LF (Internal module)
Nominal writing distance approx. 5 cm approx. 1.9 inch
Antenna Integrated in the device as a ferrite
antenna or air coil antenna
Frequency range 125/134 kHz
Transmitting power 100 mW ± 2 dB
3.1.4 Standards supported by firmware
Firmware version
Btrw-rw.V.1.40.frm
Firmware version
Btrw-hdx.V.1.40.frm
Firmware version
Btrw-ti.V.1.40.frm
HITAG S256 HDX - RO EM 4450/4550
HITAG S 2 kbit HDX (Multipage) EM4xxx (UNIQUE)
HITAG 1 EM4xxx (UNIQUE) FDX-B
HITAG 2 FDX-B BDE
Q5 BDE ISO 11784/5
ATA5567 ISO 117845 ISO Animal
EM4305 ISO Animal
3.1 RFID/LF Internal Module/only UL

Appendix A
Additional Description MC 9090ex Mobile Computer RFID
Technical data subject to change without notice.
Issue 08/2010 Page 5 of 22
3.2.1 Explosion Protection
Types 17-A119-R..1/H.......
Ex protection type II 2G Ex q [ib] IIC T4
Certification PTB 05 ATEX 2055
Types 17-A129-R..1/H.......
Ex protection type Class I Division 1 Groups C and D
Certification UL file E226123
Types 17-A169-R..1/H.......
Ex protection type Class I Division 1 Groups C and D
Class II Division 1 Groups F and G
Class III Division 1
Certification UL file E226123
3.2.2 General Data
Ambient temperature -20 °C to +40 °C -4 °F to +104 °F
Dimension (length x width x height)
MC 9090ex-K
MC 9090ex-G
231x91x105 mm 9.1x3.6x4.1 inches
231x91x193 mm 9.1x3.6x7.6 inches
Weight including battery (ATEX)
MC 9090ex-K
MC 9090ex-G
approx. 1320 g approx. 46 oz
approx. 1400 g approx. 49 oz
Weight including battery (UL)
MC 9090ex-K
MC 9090ex-G
approx. 1040 g approx. 40 oz
approx. 1170 g approx. 41 oz
3.2.3 Radio Data Transmission RFID/LF (External Module)
Nominal writing distance approx. 5 cm approx. 1.9 inches
Antenna Integrated in the device as ferrite antenna
or air coil antenna
Frequency range 125/134 kHz
Transmitting power 100 mW ± 2dB
3.2.4 Standards supported by firmware
Firmware version
Btrw-rw.V.1.40.frm
Firmware version
Btrw-hdx.V.1.40.frm
Firmware version
Btrw-ti.V.1.40.frm
HITAG S256 HDX - RO EM 4450/4550
HITAG S 2 kbit HDX (Multipage) EM4xxx (UNIQUE)
HITAG 1 EM4xxx (UNIQUE) FDX-B
HITAG 2 FDX-B BDE
Q5 BDE ISO 11784/5
ATA5567 ISO 117845 ISO Animal
EM4305 ISO Animal
3.2 RFID/LF External Module/ATEX and UL

Appendix A
Additional Description MC 9090ex Mobile Computer RFID
Page 6 of 22 Technical data subject to change without notice.
Issue 08/2010
6
3.3.1 Explosion Protection
Types 17-A119-R..2/H.......
Ex protection type II 2G Ex q [ib] IIC T4
Certification PTB 05 ATEX 2055
Types 17-A129-R..2/H.......
Ex protection type Class I Division 1 Groups C and D
Certification UL file E226123
Types 17-A169-R..2/H.......
Ex protection type Class I Division 1 Groups C and D
Class II Division 1 Groups F and G
Class III Division 1
Certification UL file E226123
3.3.2 General Data
Ambient temperature -20 °C to +40 °C -4 °F to +104 °F
Dimension (length x width x height)
MC 9090ex-K
MC 9090ex-G
231x91x105 mm 9.1x3.6x4.1 inches
231x91x193 mm 9.1x3.6x7.6 inches
Weight including battery (ATEX)
MC 9090ex-K
MC 9090ex-G
approx. 1320 g approx. 46 oz
approx. 1400 g approx. 49 oz
Weight including battery (UL)
MC 9090ex-K
MC 9090ex-G
approx. 1040 g approx. 40 oz
approx. 1170 g approx. 41 oz
3.3.3 Radio Data Transmission RFID/HF External Module
Supported standards HF ISO 15693
HF ISO 14443
Nominal reader calibration width
HF ISO 15693
HF ISO 14443
approx. 7 to 12 cm approx. 2.75 to 4.72”
approx. 1 to 6 cm approx. 0.4 to 2.36 inches
(with tags in cheque card format)
Nominal writing distance
HF ISO 15693
HF ISO 14443
approx. 7 to 12 cm approx. 2.75 to 4.72”
approx. 1 to 6 cm approx. 0.4 to 2.36 inches
(with tags in cheque card format)
Antenna integrated
Frequency range 13.56 MHz
Transmitting power 250 mW ± 2 dB
3.3.4 Standards Supported by Firmware
ISO14443-A compatible ISO14443-B compatible ISO15693 compatible
e.g. mifare, mifare Ultra
Light, my-d proximity e.g. I-Code SLI, Tag-IT HFI,
my-d vicinity, STM LRI512
I-Code 1 (optional)
3.3 RFID/HF External Module/ATEX and UL