Bartec TC77ex-NI Installation guide

BARTECGmbH
Max-Eyth-Straße 16 Fon: [phone] Support: [email protected]om
97980 Bad Mergentheim Fax: [phone] Download: http://automation.bartec.de
GERMANY Internet: www.bartec.com
FAQ - Frequently Asked Questions
Mobile Computer & Touch Computer
Touch Modes
Relevant for
 Touch Computer TC77ex-NI
 Mobile Computer MC93ex-NI
Status: March 2021
Reservation: Technical data subject to change without notice. Changes, errors and
misprints may not be used as a basis for any claim for damages.

Table of content Mobile Computer & Touch Computer
FAQ: Touch Modes
1/5 Subject to technical changes.
09/2020
Subject to technical changes.
03/2021
1.Information of this FAQ........................................................................................................................2
1.1Reference documents......................................................................................................2
2.About Touch Mode ...............................................................................................................................3
3.Note about setup procedure of Touch Mode......................................................................................3
4.Setup of Touch Mode ...........................................................................................................................4

Mobile Computer & Touch Computer
FAQ: Touch Modes FAQ
Subject to technical changes.
03/2021
2/5
1. Information of this FAQ
Read carefully before commissioning the device.
The FAQ is an additional description to the available Quick Start Guide and part of the device.
The FAQ is directed at all persons who are entrusted with handling the device.
Knowledge of the safety instructions and warnings in this FAQ and strict compliance with them
is essential for safe handling.
‒ Carefully read the FAQ and especially the safety instructions before using the device.
‒
Make the FAQ accessible to all people who are entrusted with handling the device.
Warnings are used in this FAQ - Frequently Asked Questions to warn of the risks of damage to
property and personal injuries.
1.1 Reference documents
All documents are available online from the following websites:
‒ BARTEC:www.bartec.com orhttps://automation.bartec.de/mobileE.htm
Document BARTEC Explanation
Quick Start Guide of:
 Touch Computer TC77ex-NI
 Mobile Computer MC93ex-NI
It contains:
 Guidelines on commissioning and the safe use of
hand-held scanners (including installation, safety
information related to explosion protection and
information regarding programming)
Product Reference Guide (Zebra):
 Touch Computer TC77ex-NI
 Mobile Computer MC93ex-NI
It contains:
 Guidelines for commissioning and general use of the
devices (including installation, settings and
information on programming)
Symbol Explanation
Important advice and information for the effective, efficient and environmentally
sound use of the product.

FAQ Mobile Computer & Touch Computer
FAQ: Touch Modes
3/5 Subject to technical changes.
09/2020
Subject to technical changes.
03/2021
2. About Touch Mode
The touch mode of the devices is in default set to "finger only" to be able to operate the
touch screen optimally with the fingers.
3. Note about setup procedure of Touch Mode
The following description is written for Android 10 on Touch Computer TC77ex-NI and Mobile Computer
MC93ex-NI.
The procedure can vary on other Android versions or devices.
The correct procedure is always described in the appropriate Product Reference Guide of Zebra.

Mobile Computer & Touch Computer
FAQ: Touch Modes FAQ
Subject to technical changes.
03/2021
4/5
4. Setup of Touch Mode
The device display is able to detect touches using a finger, a conductive-tip stylus, or gloved finger.
A glove can be made of medical latex, leather, cotton, or wool. For optimal performance use a
BARTEC certified and specified stylus.
1. Go to “Settings” 2. Scroll down and select “Display”
3. Touch Display > “Advanced” 4. Select “Touch panel mode”

FAQ Mobile Computer & Touch Computer
FAQ: Touch Modes
5/5
Subject to technical changes.
09/2020
Subject to technical changes.
03/2021
5. Select the touch mode for your application.
 Glove and Finger (Screen Protector off) to use a finger or a gloved finger on the screen without a
screen protector.
 Stylus and Finger (Screen Protector off) to use a finger or a stylus on the screen without a
screen protector.
 Finger Only to use a finger on the screen.
 Glove and Finger (Screen Protector on) to use a finger or a gloved finger on the screen with a
screen protector.
 Stylus and Finger (Screen Protector on) to use a finger or a stylus on the screen with a screen
protector.
 Finger and Stylus to use a finger or a stylus on the screen.
 Finger and Glove to use a finger or a gloved finger on the screen.
Example for MC93
ex
-NI with Android 10 and Build number 10-16-10.00-QG-U00-STD-HEL-04
Default setting is “Finger only” mode
6. Leave menu with touch on “Home Menu”