BEC 6300VNL User manual

Version 8.25.16
BEC 6300VNL
GigaConnect®
Wireless Broadband Router
Quick Start Guide

BEC 6300VNL 4G/LTE VoIP Wireless Broadband Router
1
Package Contents
BEC 6300VNL 3G/EVDO VoIP Wireless Broadband Router
This Quick Start Guide
RJ-45 Ethernet cable
Two 3G/EVDO detachable antennas
Power adapter

Warning
Do not use the router in high humidity or high temperatures.
Do not use the same power source for the router as other equipment.
Do not open or repair the case yourself. If the router is too hot, turn off
the power immediately and have it repaired at a qualified service center.
Avoid using this product and all accessories outdoors.
Attention
Place the router on a stable surface.
Only use the power adapter that comes with the package. Using a
different voltage rating power adaptor may damage the router.
PLEASE READ THE QUICK START GUIDE AND FOLLOW THE STEPS
CAREFULLY. THIS QUICK START GUIDE WILL HELP YOU INSTALL
THE DEVICE PROPERLY AND AVOID IMPROPER USAGE. IF YOU
NEED MORE INFORMATION ON THIS SOFTWARE CONFIGURATION,
PLEASE REFER TO THE USER MANUAL ON CD-ROM.

Quick Start Guide
2
Front Panel LEDs
LED
STATUS
DESCRIPTION
Power
Green
System is up and ready
Red
Boot failure
Battery
Green
UPS is functioning properly
Orange
UPS battery failure. Need to replace a new battery
Orange blinking
UPS AC power failure and battery functioning properly
Off
Device powered by the DC power adaptor
EWAN
Lit up
BEC 6300VNL is successfully connected with a broadband connection
device.
Green
Transmission speed is at Gigabit speed (1000Mbps)
Orange
Transmission speed is at 10/100Mbps
Blinking
Data being transmitted/received
Ethernet Port
LAN 1 ~ 3
Green
Transmission speed is at Gigabit speed (1000Mbps)
Orange
Transmission speed is at 10/100Mbps
Blinking
Data being transmitted/received
USB
Green
Connecting to a USB dongle or a hard drive.
Wireless/WPS
Green
Wireless connection established
Green blinking
Data being transmitted / received
Orange
WPS configuration is in progress
Phone
Green
Successfully registered and ready to be used.
Orange
Phone is off-hook, in-use
LTE
(Received
Signal
Strength
Indicator)
Green
RSSI greater than -69 dBm. Excellent signal condition
Green
Flashing quickly
RSSI from -81 to -69 dBm. Good signal condition
Orange
Flashing quickly
RSSI from -99 to -81 dBm. Fair signal condition.
Orange
Flashing slowly
RSSI less than -99 dBm. Poor signal condition.
Orange
No signal and the 3G/EVDO module is in service
Off
No 3G/EVDO module or 3G/EVDO module fails
Internet
Green
IP connected and traffic is passing through the device.
Red
IP request failed.
Off
BEC 6300VNL is either in bridged mode or WAN connection not ready.

BEC 6300VNL 4G/LTE VoIP Wireless Broadband Router
3
Rear Panel Connectors
PORT
MEANING
1
LTE Antenna
Screw the supplied LTE antennas onto the antenna connectors on both sides.
2
SIM Card Slot
Insert the mini SIM card (2FF) with the gold contact facing down.
Push the mini SIM card (2FF) inwards to eject it
3
Phone (1X-2X)
Connect your analog phone to this port with a RJ-11 cable.
4
USB
Connect an external USB dongle / hard drive for storage, network sharing, etc.
5
Gigabit
LAN Ethernet
(1~3)
Connect a UTP Ethernet cable (Cat-5 or Cat-5e) to one of the four LAN ports when
connecting to a PC or an office/home network of 10Mbps /100Mbps /1000Mbps
6
Gigabit EWAN
Connect to Fiber/ Cable/ xDSL Modem with a RJ-45 cable
7
UPS Jack
The 4-pin connectors are used to power the device with an external UPS battery
backup.
8
Reset
After the device is powered on, press it the reset button for 10 seconds to restore to
factory default settings (this is used when you cannot login to the router, e.g. forgot
your password)
9
WPS &
Wireless On/Off
By controlling the pressing time, users can achieve two different effects:
(1) WPS*: Press &hold the button for a few seconds to trigger WPS function.
(2) Wireless ON/OFF button: Press & hold the button for 10 seconds to turn On/Off
wireless.
*Please refer to the WPS section in the User Manual.
10
Power Jack (DC)
Connect the supplied Power Adapter to this jack.
11
Power Source
Power ON/OFF switch
(1) with Power Switch ON: power up by the supplied DC power adaptor
(2) with Power Switch OFF: power up by the UPS battery unit
1
2
8
9
1
1
1
3
5
7
4
6

Quick Start Guide
4
Hardware Connection
Hardware Installation
1. Power Connection
Select power source from using a (1) DC power adapter or (2) UPS (Uninterruptible
Power Supply)
1.1 Using the Supplied AC/DC Power Adaptor
Plug in the supplied power adapter to the wall jack, the other side to the 6300VNL then
power it ON the by pressing the Power On/Off button.
1.2 Using a UPS Battery Unit (Optional)
Power OFF the power source button and plug the uninterruptible power supply (UPS) to
the device; it’s an electrical apparatus that can provide emergency power when the main
power source fails. <Please refer to User Manual for detailed instruction.>

BEC 6300VNL 4G/LTE VoIP Wireless Broadband Router
5
2. LAN Connection
Connect the supplied RJ-45 Ethernet cable to one of the Ethernet ports, and the other
side to the PC’s Ethernet interface.
3. WAN Link Interface and Connection
BEC 6300VNL supports failover and fallback on multiple WAN interfaces, 4G LTE, EWAN
and USB 3G/4G LTE. Please refer to User Manual for detailed Internet setup.
3.1 3G/EVDO Connection
Slide the SIM card into the card slot of the device with the gold contact facing down. Make
sure that the SIM card has been slid into the bottom of the slot with a click. When removing
the SIM card, press the SIM card again it will be ejected from the card slot.
3.2 EWAN Connection (Optional)
Connect RJ-45 Ethernet cable to the EWAN port, and connect the other side to another
alternative broadband device, such as Cable Modem, VDSL, Fiber Modem or PON optic
lines.
WARNING: Please power off the device before inserting or removing the
SIM card.

Quick Start Guide
6
4. USB for Network File Sharing (Optional)
BEC 6300VNL has built-in FTP and Samba Servers, Simply plug in an external USB HD
then follow the instruction setup in the User Guide.
Connecting to the Router
The default IP of modem is 192.168.1.254 with subnet 255.255.255.0. Make sure the attached
PC to this router is in the same subnet and has an IP address in the range between 192.168.1.1
~ 192.168.1.253.
Open a web browser and type http://192.168.1.254 in the URL address bar.
The login prompt will appear. Input the default username (admin) and password (admin) for
Account type, Administrator. *This username / password may vary by different Internet Service Providers.
Quick Setup Your Router
Step 1: Change administration password
Setup a new password for “admin” account for device management. The default password is
“admin”. Click Continue to go on to the next step.
*The password may vary by different Internet Service Providers.
Step 2: Time Zone configuration
URL Address bar: type
http://192.168.1.254
New Password: assign a new,
unique password
Confirm Password: re-enter the
new password again
Next Step: click Next

BEC 6300VNL 4G/LTE VoIP Wireless Broadband Router
7
Enable and select your Time Zone then click Continue to go on to the next step.
Step 3: Setup Wireless Connection
Step 4: WAN / Internet Connection Setup
Select the appropriate WAN protocol then fill out the information provided by your ISP in all
relevant parameters.
Example: WAN Interface in EWAN mode.
Step 5: Save Confirmation Settings
Click “Next” to save and complete the Quick Setup.
You should now be able to access to the Internet.
Access Point: select Activated
SSID: Assign an unique name
Channel: pick from 1~11
Security Type: select a mode
- Disable (No security)
- WPA
- WPA2 (Most secure one)
- WPA / WPA2 (auto detect WPA mode with
wireless clients)
- WEP (Less secure one)
Pre-Shared Key: key for wireless authentication
- WPA / WAPA2 Share Key: Assign a key
between 8 ~ 63 characters.
- WEP: select Open System, use default WEP
Key 1then assign 26 Hex codes
Next Step: click Next
Protocol: select one of them
- Dynamic IP Address (Obtain an IP
automatically)
- Static IP Address (Manually assign an IP)
- PPPoE
- Bridge Mode
Net Step: click Continue
Time Zone: select your time zone
Next Step: click Next

Quick Start Guide
8
Troubleshooting
1. None of the LEDs are on when you turn on the router.
Check the connection between the adapter and the router. If the error persists, you may have
a hardware problem. In this case you should contact technical support.
2. You have forgotten your router login and/or password.
Try the default login and password, please refer to User Manual. If this fails, you can restore
your router to its factory settings by holding the Reset button on the back of your router for 6
seconds or more.
3. Can’t ping any PCs on the LAN.
Check the Ethernet LEDs on the front panel. The LED should be on for a port that has a PC
connected. If it is off, check the cables between your router and the PC. Make sure you have
uninstalled any software firewall for troubleshooting. Verify that the IP address and the subnet
mask are consistent between the router and the workstations.
Product Support and Contact Information
Most problems can be solved by referring to the Troubleshooting section in the User Manual.If
you have other inquiries or need further technical support, please contact Cellcom at 800-236-
0055 or visit us at www.bectechnologies.net.