BEC 6800RUL User manual

BEC 6800RUL
4G/ LTE Outdoor Router
Quick Start Guide

BEC 6800RUL 4G/LTE Outdoor Router
1
Package Contents
BEC 6800RUL
4G/LTE Outdoor
Router
This Quick
Installation Guide
CD containing User
Manual
M25 Cable Gland
25ft Outdoor LAN
cable
PoE Injector
Grounding Cable
Mounting Kit
PLEASE READ THE QUICK START GUIDE AND FOLLOW THE
STEPS CAREFULLY. THIS QUICK START GUIDE WILL HELP YOU
INSTALL THE DEVICE PROPERLY AND AVOID IMPROPER USAGE.
IF YOU NEED MORE INFORMATION ON THIS SOFTWARE
CONFIGURATION, PLEASE REFER TO THE USER MANUAL ON
CD-ROM.

Quick Start Guide
2
Hardware Overview
CONNECTORS
DESCRIPTION
SIM/ Reset
Insert the SIM card into the SIM slot; press the reset button to reset device
or restore to factory default settings
LAN(PoE)
Connect to a computer/ Passive PoE using an Ethernet cable.
LED Description:
LED
DESCRIPTION
LED
1. Power
Lit green when system power on.
2. LAN(PoE)
Lit green when the LAN port is connected to an Ethernet device. Blink
when data is being transmitted/ received
3. Boot LED
Lit green means system boot up successfully.
4. LTE
Lit green when 4G/LTE service is ready to precede the dial-up.
5. Internet
Lit green when Internet is available.

BEC 6800RUL 4G/LTE Outdoor Router
3
Mounting Kit Installation
1. Attach the Articulation Pole to the Enclosure
Attach the articulation pole to the back of the BEC 6800RUL using M6*16 screws and
washers.
2. Mounting on Wall or a Pole
2.1 Mounting on Wall
Fix the T-formed Bracket to the wall using wood/ drywall screws.
2.2 Mounting on a Pole
2.2.1a Mounting for pole smaller than 1.5” (38mm)
Attach the T-formed Bracket and the W-bar to the pole then use M6x60 bolts, spring washer
and washer to fix the mounting kit onto the pole.
Dual-Polarized Antenna
Cross-Polarized Antenna
A -45 or +45 degree adjustment

Quick Start Guide
4
2.2.1b Mounting for pole larger than 1.5” (38mm)
Fix the T-formed Bracket to the pole by using the stainless hose clamp.
2.2.1 Mounting BEC 6800RUL on a Pole with T-formed Bracket
Attach the articulation pole to the T-formed bracket by using M8x40 bolts, nut, spring washer
and washer.
Dual-Polarized Antenna –The original of the source position, the nominal position, is seeing BEC
logo when facing toward the 6800RUL,

BEC 6800RUL 4G/LTE Outdoor Router
5
3. Position Adjustment
3.1 Using a Embedded Directional Antenna
3.1.1 Find the location and best angle for getting the strongest signal from the base station.
The CPE must be directed towards the nearest base station.
3.3.2 Adjusting CPE position to get a better reception and/or fine-tuning the CPE orientation
(in horizontal/vertical position or 45 degree angle position) to have the best signal
strength
Cross-Polarized Antenna –From the nominal position, adjusting and rotating the 6800RUL-45 or
+45, anticlockwise or clockwise, degree angle.

Quick Start Guide
6
3.2 Using two (2) Omni Directional Antennas
3.2.1 Find the location and best angle for getting the strongest signal from the base station.
The CPE must be directed towards the nearest base station.
3.3 Using an External Yagi Antenna
Find a good spot to mount the Yagi antenna, such as a chimney or rooftop, to avoid trees,
building, and any metal objects. The Yagi antenna must be directly pointing to the nearest
base station for strongest signals.
4 Grounding the CPE to Complete the Installation
Attach the grand cable to the CPE and tighten the screw

BEC 6800RUL 4G/LTE Outdoor Router
7
Connecting to the Router
1. Power on your LTE router
Step 1: Assemble M25 cable gland
Step 2: Unscrew the LAN (PoE) port and insert the supplied outdoor Ethernet cable (RJ-45)
through material A-D, and then connect the RJ-45 Ethernet cable into the CPE port.
Step 3:
3.1: Insert ○ Cat the back end of ○ D
3.2: clip ○ B on ○ C
3.3: keep ○ B close to ○ D
3.4: then tighten ○ A .
Step 4: Insert the other end of outdoor Ethernet cable (RJ-45) to the supplied PoE injector
P+D/OUT port. Connect another Ethernet cable (RJ-45) directly to the Data/IN port and
the other end of cable to a switch or broadband router. Plug the PoE power cable to an
electrical outlet to power on your LTE router.

Quick Start Guide
8
2. Set up your LTE Internet Connection
Step 1: Unscrew the cap of SIM card slot.
Step 2: Slide the SIM card into the card slot of the device. Make sure that the SIM card is
slid into the bottom of the slot with a click.