Becker C16 User manual

P5-20...L120-11
Model: C16
en Assembly and Operating Instructions
Radio controlled sun protection drives with locking
system
Important information for:
• Fitters / • Electricians / • Users
Please forward accordingly!
These instructions must be kept safe for future reference.
Becker-Antriebe GmbH
Friedrich-Ebert-Straße 2-4
35764 Sinn/Germany
www.becker-antriebe.com
2010 300 981 026/01/2022

Table of contents
General ............................................................................................................................................................................... 3
Warranty ............................................................................................................................................................................. 3
Safety instructions ............................................................................................................................................................... 4
Instructions for the user................................................................................................................................................... 4
Instructions for installation and commissioning.................................................................................................................. 4
Intended use ....................................................................................................................................................................... 6
Assembling and disassembling the plug-in connecting cable................................................................................................... 6
Assembly ............................................................................................................................................................................ 7
Commissioning.................................................................................................................................................................. 10
Programming the master transmitter .............................................................................................................................. 11
Checking that the running direction is correct.................................................................................................................. 11
Setting the limit positions............................................................................................................................................... 12
Deleting the limit positions ............................................................................................................................................. 13
Intermediate position I in the down direction.................................................................................................................... 13
Intermediate position II in the up direction ....................................................................................................................... 14
Programming additional transmitters.............................................................................................................................. 14
Deleting transmitters..................................................................................................................................................... 15
Overwriting the master .................................................................................................................................................. 16
Local operation with a single button..................................................................................................................................... 17
Programming and deleting the run times.............................................................................................................................. 18
Programming the run times............................................................................................................................................ 18
Deleting the run times ................................................................................................................................................... 18
Activating/deactivating the additional fabric untensioning function with the master transmitter................................................. 18
Disposal ............................................................................................................................................................................ 18
Maintenance ..................................................................................................................................................................... 18
Technical data dia. 35 ........................................................................................................................................................ 19
Technical data dia. 45 ........................................................................................................................................................ 19
Technical data dia. 58 ........................................................................................................................................................ 20
What to do if...?.................................................................................................................................................................. 20
Declaration of conformity ................................................................................................................................................... 21
2-en

General
These tubular drives are high-quality products with the following features:
•Optimised for sun protection applications with locking system
•Locking limit position and unlocking limit position freely programmable
•Automatic detection of upper limit position
•Several drives can be operated in parallel
•Compatible with existing drives with electronic limit switching (4-core connecting cable)
•Comprehensive range of the drive manufacturer's control units can be used
•Smooth operation of the system and the drive increases the service life
•Individual, group and central radio control
•No need to run wires to a switch or relay control device
•Any combination of drive and transmitter possible
•Simple to set the limit positions with the transmitter
•Setting of an intermediate position I in the down direction possible
•Setting of an intermediate position II in the up direction possible
•Flexible radio grouping; can be altered at any time with no need to install/uninstall
•For plug-in connecting cable
Please observe these Assembly and Operating Instructions when installing and setting the equipment.
The date of manufacture comes from the first four digits of the serial number.
The numbers 1 and 2 indicate the year and the numbers 3 and 4 indicate the calendar week.
Example: 34th calendar week in 2020
Ser. No.: 2034XXXXX
Explanation of pictograms
CAUTION CAUTION indicates a hazardous situation which, if not avoided, could
result in injury.
ATTENTION ATTENTION indicates measures that must be taken to avoid damage to
property.
Denotes user tips and other useful information.
Warranty
Structural modifications and incorrect installation which are not in accordance with these and our other instructions can result in
serious injuries, e.g., crushing of limbs. Therefore, structural modifications may only be carried out with our prior approval and
strictly in accordance with our instructions, particularly the information contained in these Assembly and Operating Instructions.
Any further processing of the products which does not comply with their intended use is not permitted.
The end product manufacturer and fitter have to ensure that all the relevant current statutory, official and, in particular, EMC regu-
lations are adhered to during utilisation of our products, especially with regard to end product manufacture, installation and cus-
tomer advice.
3-en

Safety instructions
The following safety instructions and warnings are intended to avert hazards and to prevent property damage and personal injury.
Instructions for the user
General information
•The drive must be disconnected from its power source during cleaning and maintenance and when re-
placing parts.
•All work, including maintenance and cleaning, on electrical installations as well as other system parts
must always be performed by trained technicians, in particular qualified electricians.
•Children from the age of 8 years and persons with reduced physical, sensory or mental capabilities or
lack of experience and/or knowledge may use these devices, provided they are supervised or have
been instructed in the safe use of the device, and have understood the hazards involved. Children must
not play with the device.
•Systems have to be checked regularly by authorised specialists for wear and damage.
•Always put damaged systems out of operation immediately until they are repaired by an authorised
specialist.
•Do not operate equipment if people or objects are within the danger zone.
•Observe the danger zone of the equipment during operation.
•Ensure that there is adequate clearance (at least 40 cm) between moving parts and adjacent objects.
Caution
Safety instructions for avoiding serious injuries.
•Crushing or shearing points must be avoided or protected.
Instructions for installation and commissioning
General information
•Observe the safety instructions in EN 60335-2-97. Please note that this list of safety instructions is not
exhaustive, since it would be impossible for the standard to include all sources of danger. For example,
the design of the operated product, the way the drive works in the situation it is installed in or even the
way the end product is mounted in the end user’s place of use cannot be taken into consideration by
the drive manufacturer.
If any questions or uncertainties regarding the safety instructions contained in the standard arise,
please contact the manufacturer of the part or end product in question.
•All applicable standards and regulations for electrical installation must be complied with.
•All work, including maintenance and cleaning, on electrical installations as well as other system parts
must always be performed by trained technicians, in particular qualified electricians.
•Only use spare parts, tools and accessory devices which have been approved by the drive manufac-
turer.
Unapproved third-party products or modifications to the system and its accessories represent a risk to
your safety and the safety of others. This means that the use of unapproved third-party products, or
modifications which have not been agreed with or approved by us, are prohibited. We do not accept li-
ability for damage or injury arising from such actions.
•Position switch with OFF presetting within sight of the driven product, but away from moving parts, at a
height of over 1.5 m. This must not be publicly accessible.
•Permanently mounted control devices must be positioned where they can be seen.
•Rated torque and duty cycle must be suitable for the requirements of the driven product.
Technical data - rated torque and service life can be found on the type plate of the tubular drive.
4-en

•Hazardous moving parts of the drive must be installed at a height of over 2.5 m above floor level or any
other surface from which the drive can be accessed.
•To ensure safe operation of the system after commissioning, the limit positions must be correctly set/
programmed in.
•Drives with a H05VV-F connecting cable may only be used indoors.
•Drives with a H05RR-F, S05RN-F or 05RN-F connecting cable may be used both indoors and outdoors.
•To connect the drive to the driven part, solely mechanical accessory components made by the drive
manufacturer from the current product catalogue may be used. The components must be installed in
accordance with the manufacturer's instructions.
•If the drive is used for shading solutions in a specially marked area (e.g., escape routes, hazard zones,
safety areas), compliance with all applicable regulations and standards must be ensured.
Caution
Safety instructions for avoiding serious injuries.
•When electrical or electronic equipment and units are operated, certain components,
e.g., the power supply unit, are live. Physical injuries or damage to property can result in
the event of unauthorised interventions or failure to heed warnings.
•Be careful when touching the tubular drive, as it heats up during operation for technical
reasons.
•Before installation, shut down all lines and control devices that are not essential for op-
eration.
•Crushing or shearing points must be avoided or protected.
•When installing the drive, all-pole disconnection from the mains with a contact gap of at
least 3mm per pole must be provided (EN60335).
•If the mains connecting cable is damaged, it may only be replaced by the manufacturer.
If the drive has a plug-in connecting cable, it must be replaced with the same type of
mains connecting cable, which is available from the drive manufacturer.
Attention
Safety instructions for avoiding property damage.
•Ensure that there is adequate clearance between moving parts and adjacent objects.
•The drive must not be carried by the mains connecting cable.
•All latching connections and fastening screws on the brackets must be checked to en-
sure that they are secure.
•Ensure that nothing rubs against the tubular drive, such as shading solution attach-
ments, screws, etc.
•The drive must be fitted horizontally.
5-en

Intended use
The type of tubular drive described in these instructions is intended solely for the operation of sun protection systems with locking
systems . To function properly, these tubular drives need a fixed stop in the upper limit position (retracted blind).
When mounting connection parts on the drive dia. 35 mm PXX/XX, only use screws EJOT Delta PT 40x12 WN 5454 Torx (9900 000
545 4).
It may only be used in networked systems if all the individual drives are exactly synchronised and reach the upper limit position at
the same time.
For roller shutter applications, please use only the types of tubular drive designed for this purpose.
This type of tubular drive is designed for use in single systems (one drive per barrel).
The tubular drive must not be used in potentially explosive areas.
The connecting cable is not suitable for transporting the drive. Always carry the drive by the housing tube.
Other applications, uses and modifications are not permitted in order to protect the safety of the users and others, since these ac-
tions can impair the system’s safety and carry the risk of personal injury and property damage. The drive manufacturer does not
accept liability for damages or injury arising from such actions.
Always observe the information in these instructions when operating or repairing the system. The drive manufacturer does not ac-
cept liability for damage or injury resulting from improper usage.
Assembling and disassembling the plug-in connecting cable
Caution
The power supply to the connecting cable must be disconnected prior to assembly/disas-
sembly.
Assembling the plug-in connecting cable
Ø35/Ø45/Ø58 Insert the dead connecting cable into the drive head until the
locating lug clicks into place in the drive. If necessary, use a
suitable flathead screwdriver to assist with insertion. Set the
screwdriver into one of the two plug grooves provided for this
purpose.
Check that the cable is properly engaged.
1 = locating lug
Disassembling the plug-in connecting cable for tubular drives
Ø35 Insert a suitable flathead screwdriver between the locating lug
and the snap-in pin, so that the snap-in pin releases the locat-
ing lug from the plug.
Now you can pull out the connecting cable along with the flat-
head screwdriver.
1.
2.
3.
A
A = snap-in pin
6-en

Ø45/Ø58 Insert a suitable flathead screwdriver right into the recess of the
locating latch, so that the latch releases the locating lug from
the plug.
Now you can pull out the connecting cable along with the flat-
head screwdriver.
A
1. 2.
A = locating latch
Assembly
Assembling the drive
Attention
To connect the drive to the driven part, solely mechanical accessory components made by
the drive manufacturer from the current product catalogue may be used.
Prior to mounting, the fitter must ensure that the masonry and the system being motorised are sufficiently robust (drive torque plus
weight of the shading solution).
Caution
Electrical connections may only be carried out by a qualified electrician. Prior to assembly,
the power supply must be disconnected and secured. Please give the enclosed connection
information to the responsible electrical contractor.
Calculate the space required at the side (M) by measuring the drive head (1) and wall bracket (2). The
clear dimension of the box (X) minus the space required at the side (M) and idler (G) gives the length
(L) of the barrel: L=X-M-G.
The space required at the side (M) varies depending on the combination of drive and wall bracket.
Then mount the wall bracket and idler. Ensure that the barrel is aligned at right angles to the wall and that sufficient axial play is al-
lowed for the mounted system.
Undoing the mounting pin
Undoing the mounting pin
When pushed in, the mounting pin (2) locks automatically. To undo the mounting pin (2), push the tab
washer (1) upwards and pull out the mounting pin (2).
Assembling and disassembling the drive adapter
Fitting the ring onto the thrust ring
Assembling the drive adapter with safety catch on the
drive shaft
Dismantling the drive adapter with safety catch on the
metal drive shaft
7-en

Disassembling the drive adapter with safety catch on the drive shaft
Disassembling with the disassembly tool
Item no. 4930 300 606 0
Disassembly with long nose pliers
2.
1.
Assembling and disassembling the drive adapter with drive adapter safety catch or screw connection
Assembling and disassembling the drive
adapter with separate drive adapter
safety catch
Assembling and disassembling the drive
adapter with screw connection
Mounting the drive in the tube
For profile shafts:
In the case of some drive adapters, tolerances of the groove widths in different barrels can be offset by
rotating the drive adapter into a different groove recess. These groove recesses have different sizes
and allow the drive to fit exactly.
Y
X
For round shafts:
Measure the lug of the thrust ring (X, Y). Then notch the tube on the motor side, so the lug of the thrust
ring can also be pushed into the shaft. There must be no play between the lug of the thrust ring and the
shaft.
-10 mm
To ensure secure torque transmission for round shafts, we recommend screwing the drive adapter to
the shaft (see the table below).
Attention!When drilling into the barrel, never drill near the tubular drive!
Size of drive
[mm]
Drive adapter Torque
max. [Nm]
Fastening screws
(4 units)
dia. 35-dia. 45 All Up to 50 Self-tapping screw
dia. 4.8 x 9.5 mm
dia. 58 Aluminium drive adapter Up to 120 Countersunk screw
M8 x 16 mm
dia. 58 Diecast drive adapter Up to 120 Self-tapping screw
dia. 6.3 x 13 mm
We also recommend screwing the idler to the barrel.
Attention
Do not hammer the tubular drive into the tube or drop it into the barrel!
2
1
Assemble the tubular drive with the relevant ring (1) and drive adapter (2). If the ring has several
grooves, select the groove which is a perfect fit and push the ring (1) onto the thrust ring.
Insert the tubular drive with the pre-assembled ring (1) and drive adapter (2) into the tube to achieve a
form fit. Ensure that the ring and drive adapter are secure in the tube.
Mount the assembled unit comprising shaft, tubular drive and idler on the box and secure the drive with
a splint or spring pin according to the type of wall bracket fixing.
8-en

Lay the connecting cable
Lay the connecting cable up to the tubular drive, and fix The connecting cable and any antennae must
not project into the winding chamber. Cover any sharp edges.
9-en

Commissioning
Explanation of symbols
UP button
STOP button
DOWN button
Programming button
Receiver confirms once or multiple times by “clicking” or “shifting”
1 = direction switch
2 = radio switch
Unlocked
Locked
Locking bolt Moving part of the locking system on the front section of the sun protection
system
Bolt mechanism Fixed part of the locking system in the guide track of the sun protection sys-
tem
N1
2
1
2
4
3
4
230V AC / 50 Hz
L1
PE
Connecting the tubular drive
Connect the tubular drive to the power supply.
1 = blue 3 = black
2 = brown 4 = green-yellow
Readying the tubular drive for programming
Readying the tubular drive for programming by switching on the power
▻Switch on the power.
►The tubular drive is ready to programme for 3 minutes
If several tubular drives are to be connected in parallel, you can deactivate the program-
ming mode on one tubular drive by switching the radio switch to the outside position after
turning the power on.
10-en

Readying the tubular drive for programming with the radio switch
Switch the radio switch to the inside position. If the radio switch is already in this posi-
tion, switch it to the outside and back to the inside position.
►The tubular drive is ready to programme for 3 minutes
Programming the master transmitter
3s Press the programming button for 3 seconds when it is ready to programme.
▻The tubular drive acknowledges.
►The programming process is now complete.
If a transmitter is already programmed on the receiver, press the programming button for
10 seconds.
Checking that the running direction is correct
The direction of rotation can only be changed if no limit position has been set.
There are several ways to change the direction of rotation:
•Changing direction of rotation via the direction switch
•Changing direction of rotation via master transmitter
Changing direction of rotation via the direction switch
Press the or button.
▻The shading solution runs in the desired direction
►The running direction is OK.
If the shading solution runs in the wrong direction, the running direction must be changed. Proceed as follows:
Switch the direction switch (1) to the opposite position.
▻The running direction will now have changed.
►Check the running direction again.
11-en

Changing direction of rotation via master transmitter
Press the or button.
▻The shading solution runs in the desired direction.
►The running direction is OK.
If the shading solution runs in the wrong direction, the running direction must be changed. Proceed as follows:
3s
First, press the programming button, then within 3seconds also press the and
button for 3seconds.
►The tubular drive confirms.
Check the running direction again.
Setting the limit positions
Limit position status indicator
A brief stopping and restarting indicates that no limit position has been set in that direction of movement.
Attention
The tubular drives are designed for short-time operation (for the operating mode, please
see technical data). An inbuilt thermal protection switch prevents overheating of the tubu-
lar drive. During commissioning (long drop distance or long running time), the ther-
moswitch may trigger. The drive will switch off. After a short cooling-down period, the sys-
tem is ready for operation again.
The drive does not achieve its full duty cycle until it has cooled to ambient temperature.
Avoid a situation where the thermal protection switch cuts in repeatedly.
The limit positions can only be set with the master transmitter. The shutter direction must
be correct. When setting the limit positions, the tubular drives runs in dead-man mode. If
the tubular drive switches off prematurely while opening, due to an obstruction, the ob-
struction can be cleared by closing the screen and removing the obstruction. The upper
limit position can be set by opening again.
Installation step 1:
First, press the UP button to retract to the upper limit position, until the tubular drive
switches itself off .
Installation step 2:
Run the bolt past the locking point and stop the tubular drive. Now press the pro-
gramming button and also the DOWN button for about 3 seconds. The tubular drive
acknowledges and the locking limit position is saved.
Installation step 3:
Use the UP button to run the bolt in the open direction until it is engaged by the bolt
mechanism. The tubular drive switches off automatically.
12-en

Installation step 4:
Use the DOWN button to run the bolt in the down direction and disengage it from the
bolt mechanism, and then stop the tubular drive immediately. Now press the pro-
gramming button and also the DOWN button for about 3 seconds. The tubular drive
acknowledges and the unlocking limit position is saved.
►Limit positioning is now complete.
The blind will now lock and unlock automatically in the lower limit position when you
close and open it.
Deleting the limit positions
Attention
When the limit positions are deleted, all the other set functions (intermediate position I, in-
termediate position II) are deleted as well.
Once set, the limit positions can only be deleted with the master transmitter.
10s
Press the programming button and, within the next 3 seconds, press the STOP button
at the same time and hold the two buttons down for 10 seconds.
▻The tubular drive acknowledges.
►The limit positions are now deleted.
Intermediate position I in the down direction
The intermediate position I is any shading solution position of your choosing. It is not pos-
sible to set an intermediate position I in the area of the limit position Both limit positions
must be set before the intermediate position I is set.
When both limit positions are deleted, this set function is deleted as well.
Setting the intermediate position I
Travel the shading solution to the desired intermediate position I.
Press the STOP button and, within 3 seconds, also press the DOWN button and hold the two but-
tons down.
▻The tubular drive acknowledges.
►The intermediate position I is now saved.
Checking the intermediate position I
2x Press the DOWN button twice within one second.
►The shading solution runs to the intermediate position I.
Deleting the intermediate position I
2x Move the shading solution to the intermediate position I.
Press the STOP button and, within 3 seconds, also press the DOWN button and hold the two but-
tons down.
▻The tubular drive acknowledges.
►The intermediate position I is now deleted.
13-en

Intermediate position II in the up direction
The intermediate position II is any shading solution position of your choosing. It is not pos-
sible to set an intermediate position II in the area of the limit position. Both limit positions
must be set before the intermediate position II is set.
When both or individual limit positions are deleted, this set function is deleted as well.
Setting the intermediate position II
Travel the shading solution to the desired intermediate position II .
Press the STOP button and, within 3 seconds, also press the UP button and hold the
two buttons down.
▻The tubular drive acknowledges.
►The intermediate position II is now saved.
Checking the intermediate position II
2x Press the UP button twice within one second.
►The shading solution runs to the intermediate position II.
Deleting the intermediate position II
2x Move the shading solution to the intermediate position II.
Press the STOP button and, within 3 seconds, also press the UP button and hold the
two buttons down.
▻The tubular drive acknowledges.
►The intermediate position II is now deleted.
Programming additional transmitters
In addition to the master transmitter, up to 15 further transmitters can be programmed in
the tubular drive. Before programming a radio controlled Sun-Wind-Sensor, the limit posi-
tions must be programmed.
3s Press the programming button of the master transmitter for 3 seconds.
▻The tubular drive acknowledges.
3s Now press the programming button of a new transmitter which has not yet been pro-
grammed in the tubular drive for 3 seconds. Doing so activates the programming
mode of the tubular drive for a new transmitter for 3 minutes.
▻The tubular drive acknowledges.
3s Now press the programming button of the new transmitter you wish to program again
for 3 seconds.
▻The tubular drive acknowledges.
►The new transmitter has now been programmed.
14-en

Deleting transmitters
Deleting individual transmitters
The programmed master transmitter cannot be deleted. It can only be overwritten (see
Programming the master transmitter [}11]).
3s Press the programming button on the master transmitter for 3 seconds.
▻The tubular drive acknowledges.
3s Now press the programming button of the transmitter to be deleted for 3 seconds.
▻The tubular drive acknowledges.
10s Then press the programming button of the transmitter to be deleted again for 10
seconds.
▻The tubular drive acknowledges.
►The transmitter is now deleted from the tubular drive.
Deleting all transmitters (except the master transmitter)
3s Press the programming button on the master transmitter for 3 seconds.
▻The tubular drive acknowledges.
3s Re-press the programming button on the master transmitter for 3 seconds.
▻The tubular drive acknowledges.
10s Re-press the programming button on the master transmitter for 10 seconds.
▻The tubular drive acknowledges.
►All transmitters (except the master transmitter) are now deleted from the re-
ceiver.
15-en

Overwriting the master
There are two ways to overwrite the master:
•Readying the tubular drive for programming by switching on the power
•Readying the tubular drive for programming with the radio switch
Readying the tubular drive for programming by switching on the power
To ensure that the new master transmitter is programmed in the desired tubular drive only,
all other tubular drives which are connected to the same power supply must be deactivated
from the programming mode. To do so, after switching back on the power, execute a drive
or stop command using the transmitter for the given tubular drives or switch the radio
switch from inside to outside. If the radio switch is already in this position, switch it to the
inside and back to the outside position.
N1
2
1
2
4
3
4
230V AC / 50 Hz
L1
PE
Switch off the tubular drive power for 5 seconds, then switch it back on.
▻The tubular drive is ready to program for 3 minutes.
1 = blue 3 = black
2 = brown 4 = green/yellow
10s Now press the programming button of the new master transmitter for 10 seconds.
▻The tubular drive acknowledges.
►The new master transmitter has now been programmed and the old master trans-
mitter overwritten.
Readying the tubular drive for programming with the radio switch
Switch the radio switch to the inside position. If the radio switch is already in this posi-
tion, switch it to the outside and back to the inside position.
▻The tubular drive is ready to program for 3 minutes.
10s Now press the programming button of the new master transmitter for 10 seconds.
▻The tubular drive acknowledges.
►The new master transmitter has now been programmed and the old master
transmitter overwritten.
16-en

Local operation with a single button
Connection
Only use a single button (normally open). Only connect one drive for each push-button.
The length of cable between the tubular drive and the push-button must not exceed 20m.
The push-button must not be operated during the first five seconds after the mains voltage
has been switched on.
N
L
PE
Button (normally open)
black brown blue green/yellow
Button commands
< 1 second Moves in maintained operation
> 1 second Moves in dead-man mode
Double-tap < 1 second Moves to the intermediate position (in alternation if both are programmed)
Operation proceeds in this sequence: "Travel-Stop-Travel-in-the-opposite-direction-Stop".
17-en

Programming and deleting the run times
Programming the run times
This function is only available with MemoControl transmitters from the Becker Centronic
range of control units.
This tubular drive can save one switching time for one retraction and one extension cycle.
In the “Timer” slide switch position, the retraction and extension cycles are automatically repeated every 24 hours.
It does not matter what position the manual/auto slide switch is in when programming the switching time. Previously stored switch-
ing times are overwritten.
1. The tubular drive must be in the upper limit position to program the Extend run time, and must be in the lower limit position for
the Retract run time.
2. Wait for the time you wish the automatic drive command to be executed.
3. At the desired time, press and hold the relevant direction button until the tubular drive briefly stops after approx. 6seconds
and then continues to the limit position.
4. Release the direction button.
The tubular drive has saved the current time for this direction of travel.
Deleting the run times
When deleting, both run times are always deleted.
To delete the retract and extend run time, press the STOP button for 10 seconds. The tubular drive makes a "click click" sound to
confirm.
The run times are now deleted.
Activating/deactivating the additional fabric untensioning function with the
master transmitter
The "to retracted stop" limit position must be set for the fabric untensioning function.
This function is deactivated on delivery.
Activating/deactivating the fabric untensioning function
Open the shading solution to the Retract limit position.
3s
Then press the programming button, and also the STOP and Extend buttons for ap-
proximately 3seconds.
►The tubular drive confirms.
Disposal
This product is made of various materials which must be disposed of properly. Find out about the applicable regulations on recyc-
ling or disposal for this product in your country.
The packaging material must be disposed of properly.
Maintenance
These drives are maintenance-free.
18-en

Technical data dia. 35
Tubular drive P5-20 P9-16
Model C16
Type C SEF I2
Rated torque [Nm] 5 9
Output speed [rpm] 20 16
Limit switch range 64revolutions
Supply voltage 230V AC/ 50Hz
Connected load [W] 115 110
Rated current consumption [A] 0.47 0.47
Operating mode S24min
Degree of protection IP44
Min. tube inside diameter [mm] 37
Frequency 868.3 MHz
Emission sound pressure level [dB(A)] ≤70
Technical data dia. 45
Tubular drive R8-17 R12-17 R20-17 R30-17 R40-17
Model C16
Type C SEF I2
Rated torque [Nm] 8 12 20 30 40
Output speed [rpm] 17 17 17 17 17
Limit switch range 64revolutions
Supply voltage 230V AC/ 50Hz
Connected load [W] 100 110 160 205 260
Rated current consumption [A] 0.45 0.50 0.75 0.90 1.15
Operating mode S24min
Degree of protection IP44
Min. tube inside diameter [mm] 47
Frequency 868.3 MHz
Emission sound pressure level
[dB(A)]
≤70
19-en

Technical data dia. 58
Tubular drive L50-17 L70-17 L80-11 L80-17* L100-11 L120-11
Model C16
Type C SEF I2
Rated torque [Nm] 50 70 80 80 100 120
Output speed [rpm] 17 17 11 17 11 11
Limit switch range 64revolutions
Supply voltage 230V AC/ 50Hz
Connected load [W] 315 430 310 470 354 435
Rated current consumption [A] 1.40 1.90 1.40 2.10 1.56 1.90
Operating mode S24min
Degree of protection IP44
Min. tube inside diameter [mm] 60
Frequency 868.3 MHz
Emission sound pressure level
[dB(A)]
≤70
*) This tubular drive is not yet available.
What to do if...?
Problem Remedy
Tubular drive does not move. Program new transmitter.
Bring transmitter within range of the tubular drive.
Press drive or stop button on transmitter at least five times in
the immediate vicinity of the tubular drive.
Insert battery/batteries correctly in the transmitter or insert new
battery/batteries.
Check electrical connection.
Thermal protection switch in tubular drive has tripped. Wait until
the thermal protection switch in the tubular drive is reactivated.
Running direction on tubular drive cannot be set. Delete limit positions (see chapter Deleting limit positions) and
reset the running direction.
Incorrect running direction after deleting limit positions. Use the master transmitter or the direction switch on the tubular
drive to change the direction of rotation.
Tubular drive stops arbitrarily; cannot be restarted in the same
direction.
Tubular drive has detected an increase in load. Briefly run the
curtain in the opposite direction, then continue in the desired
direction.
Tubular drive is overloaded. Use a higher-torque tubular drive.
Delete limit positions, then reprogram limit positions.
Tubular drive is not locking.
Tubular drive automatically approaches the locking point 3
times.
The locking point is not correctly programmed. Reprogram limit
positions.
Tubular drive is not unlocking.
Tubular drive automatically approaches the unlocking point 5
times.
The unlocking point is not correctly programmed. Reprogram
limit positions.
20-en