Befaco FX BOY User manual

FX BOY
USER MANUAL
MANUAL IN DEVELOPMENT

USER MANUAL
FX BOY POWER & INTRO
POWERING THE
MODULE
THANKS FOR PURCHASING A MODULE FROM BEFACO!
BEFORE YOU PLUG THIS MODULE IN...
INTRODUCTION WHAT IS FX BOY?
It is a multi-fx processor with the FX stored in console cartridges. This approach, even if it can look bizarre at
rst sight, allows you to change analog and digital algorithms on the y just by swapping the carts.
Each cart is a little piece of hardware, like a guitar pedal you can embed on your modular synth and change
for others without touching a single cable.
All controls are CV controllable for real-world modular fun.
The cart set you received with your module, is designed in collaboration with several talented manufacturers.
Yes… A crazy idea with the support of a bunch of crazy people.
Enjoy!
1. Disconnect your cabinet from the mains.
2. Triple check the power cord polarity. The coloured line on the cable
(pin number one) is the -12V rail.
3. If you plug the module backwards you might burn it out and
unfortunately this is not covered by the warranty.
4. WARNING: NEVER ATTEMPT TO PLUG ANY FX BOY CARTRIDGE
INTO ANY DEVICE OTHER THAN FX BOY, NOR PLUG CARTRIDGES FROM OTHER
PLATFORMS INTO FX BOY, EVEN IF THEY LOOK SIMILAR.
It will cause unpredictable and permanent harm to either FX BOY, the cartridges,
or any third-party electronic devices you connect the cards to.
Befaco is not responsible for any damage caused to yourself, the FX BOY, the
FX BOY cartridges, or any other third-party device by not following this advice.
5. If you have any questions about this product feel free to contact us
support@befaco
.2

.3
PANEL CONTROLSCONTROLS
FXBOY
HI
IN
MID L
MID H
LOW
DRY/WET
X
DRY/WET
X CV
Y CV
X CV
Y CV
Y
EQ
FX
EQ
EQ
FX
OUT
+
+
+
+
+
+
A
B
OUT
FX BOY USER MANUAL CONTROLS
3
2
4
5
8
9
13
18
10
14
19
11
17
20
12
15
21
16
22
6 7
1
1. CARTRIDGE SLOT: Here is where you plug the dierent cards.
Cards are hot-swappable although some pops or little glitches can
occur depending on the cartridge.
Mind cartridge orientation while plugging it. The front side (the one
with the label) should face to the left.
2. “X” CONTROL: Manual control of parameter “X” . The function
of this parameter depends on the inserted cartridge. Please refer to
the Cartridge reference for detailed information on specic cards.
3. “X” CV ATTENUATOR: Controls the amount of CV that is added
(or subtracted) to the “X” Manual control
4. “Y” CONTROL. Manual control of parameter “Y”. The function of
this parameter depends on the inserted cartridge. Please refer to
the Cartridge reference for detailed information on specic cards.
5. “Y” CV ATTENUATOR: Controls the amount of CV that is added
(or subtracted) to the “Y” Manual control
6. MODE SELECTOR: All cartridges have two modes of operation
A and B. What these modes do depends on the cartridge design.
Please refer to the Cartridge reference for detailed information on
specic cards.
7. PEEK METER: Green indicates the presence of a signal at the
module’s output. Red indicates the signal has been clipped.
8. DRY/WET CONTROL: Manual control of the proportion between
the incoming non-processed and the Processed signal.
9-10-11-12. EQ BANDS LEVEL CONTROLS: Manual control to
boost or attenuate the four dierent bands of the equaliser. Each
of the four knobs controls the LO, MID-LOW, MID-HI, and HI bands
respectively. At mid position (12:00) They do not act. Clockwise they
boost and anticlockwise they attenuate.
13-14-15-16. EQ BANDS CV INs: Control voltage INs for the four
dierent bands of the equaliser. A range of 10 volts is expected and
these voltages are added to the manual controls:
With manual control at the centre, a 10V. bipolar voltage source
(like an LFO ranging +/-5 volt) will move from silence to maximum
volume.
With the manual control at the minimum position (knob full
anticlockwise) an unipolar 10V. the voltage source will move from
silence to maximum volume.
With the manual control knob fully clockwise -10v to 0v will be
accepted.
Other voltages are ignored and don’t represent any danger to the
module.
17. EQ POSITION SWITCH: Manual Control to select if the equalized
is placed before or after the FX Cartridge.
18. AUDIO IN: Modular level audio input. A bipolar signal of around
10 volts is expected at this IN.
19-20. “X” AND “Y” CONTROLS CV INs: A range of 10 volts is
expected. This voltage is added to the one generated by the manual
control, allowing negative voltages in the same amount the manual
control is positive:
- With the manual DRY/WET knob anticlockwise CV can go from 0 to
10V.
- With the manual DRY/WET knob in the middle CVs go from -5v to 5v.
- With the manual DRY/WET knob fully clockwise -10v to 0v will be
accepted.
Other voltages are ignored and don’t represent any danger to the
module.
21. DRY/WET CV IN: A range of 10 volts is expected. This voltage is
added to the one generated by the manual control, allowing negative
voltages in the same amount the manual control is positive:
- With the manual DRY/WET knob anticlockwise CV can go from 0 to
10V.
- With the manual DRY/WET knob in the middle CVs go from -5v to
5v.
- With the manual DRY/WET knob fully clockwise -10v to 0v will be
accepted.
Other voltages are ignored and don’t represent any danger to the
module.

.4
CARTRIDGE REFERENCEMISCELLANEA
FX BOY USER MANUAL REFERENCE
Name Brand Mode/Function X Y
Making Sound
Machines
AWAVEFOLDER
CV X and Y add FOLD CV 1 FOLD CV 2 use with LFO
B
WAVEFOLDER
CV X is Fold, CV Y is
Audio
FOLD CV OFFSET / MOD
use with Audio
Tesseract
Modular
ARING MOD +
DOWNSAMPLING RING MOD INIT VOL SAMPLING FREQUENCY
B
RINGMOD +
DOWNSAMPLING +
FOLDER
RING MOD INIT VOL SAMPLING
FREQUENCY
TouellSkouarn
AFUZZ A GAIN FEEDBACK
BFUZZ B GAIN FEEDBACK
Feedback
Modules
AFLANGER LFO SPEED FEEDBACK
BCOMB FILTER (DELAY) DELAY TIME FEEDBACK
XOR Electronics
ADELAY TIME FEEDBACK
BGRANULAR SIZE GRAINS
Instruō
AALLPASS FILTER PHASE FEEDBACK
BPHASER LFO SPEED FEEDBACK
Befaco
AHARDER DISTORTION SLAG POISON
BHARD DISTORTION SLAG POISON
At the date of writing this manual, FX Boy is shipped with the “Founders Cartridge Pack”
composed of seven dierent FX:

.5
SPECS AND CREDITSMISCELLANEA
STRUCTURE AND SIGNAL FLOWMISCELLANEA
The feature set on the FX BOY is very straightforward and will feel very familiar if you used any FX unit before.
Two parameters X & Y and one switch are available for manual and CV control. The function of these controls depends
on the cartridge installed. Please refer to the Cartridge reference for detailed information on specic cards.
Any signal present at the Input will be processed by the cartridge and the 4-Band Equalizer. Then the processed signal is
mixed back with the dry signal and sent to the output.
A switch is provided to let you choose if the EQ is placed pre-FX or post-FX.
FX BOY MISCELLANEAUSER MANUAL
Size: 12HP
Deeth: 35 mm
+12v: 125 mA
-12v: 100mA
This module is the result of hours of development of an idea
that seemed to be crazy.
Thanks to the “Founders Cartridge Pack” designers who instantly
said yes to the collaboration proposal, you guys are great.
https://www.befaco.org/fx-boy
More information and support