Behringer C-1 User manual

User Manual
STUDIO CONDENSER
MICROPHONE
Studio Condenser Microphone

2STUDIO CONDENSER MICROPHONE C-1 User Manual
Important Safety
Instructions
Terminals marked with this
symbol carry electrical current of
sucient magnitude to constitute
risk of electric shock. Use only high-quality
commercially-available speaker cables with
¼"TS plugs pre-installed. All other installation
or modication should be performed only by
qualied personnel.
This symbol, wherever it appears,
alerts you to the presence of
uninsulated dangerous voltage
inside the enclosure - voltage that may be
sucient to constitute a risk of shock.
This symbol, wherever it appears,
alerts you to important operating
and maintenance instructions in
the accompanying literature. Please read
the manual.
Condenser microphones are
extremely moisture-sensitive.
Never use your microphone in
close proximity to water (e.g. bath tubs, wash
basins, sinks, washing machines, pools, etc.).
Always use the power
supply specied in the
operating instructions.
Take care not to drop your
microphone as this can lead to
severe damage. BEHRINGER
assumes no liability for any damage caused
by the user.
After each use, wipe the
microphone down with a soft cloth
and place it back into its protective
casing (included with the microphone).
The small bag containing the
moisture-absorbing crystals should remain
in the casing to help keep your microphone dry.
CAUTION
Never dismount the screen holding
the capsule, as this can damage
the microphone! Never try to modify the printed
circuit board inside your C-1! This can lead to
microphone damage that cannot be repaired.
Any such attempt will void the warranty.
Limited Warranty
Please register your new BEHRINGER
equipment right after your purchase by
visiting behringer.com and read the terms
and conditions of our warranty carefully.

3STUDIO CONDENSER MICROPHONE C-1 User Manual
Power Supply1.
Your condenser mic C-1 needs a phantom power supply (+36 to +52 V). If your
C-1 is connected to a microphone preamp and supplied with phantom power,
the LED on the microphone lights up. BEHRINGER assumes no liability for any
damage caused by a defective phantom power supply. Always mute the sound
reinforcement system before you switch on the phantom power supply.
Directivity2.
Your C-1 features a capsule with a cardioid pickup pattern and is ideal for
recording individual instruments, vocals and speech. Cardioid pickup pattern
means that the sound produced by sources located in front of the mic is strongly
picked up. It is often used in recording situations, since this directivity pattern
tones down the pickup of sounds located to the back of the microphone.
Microphone Installation3.
There is an adapter on your microphone that lets you mount it on mic stands with
either metric (Europe) or imperial-gauge threads (North America). First dismantle
the microphone from the stand mount adapter by detaching the ne-thread
shoulder screw at the bottom end of the microphone. Fasten the adapter onto
the microphone stand, place the microphone into it and tighten the screw again.
Basically, the microphone in the stand mount adapter should stand upright
and face the sound source at a right angle. The angle of the microphone to the
sound source inuences the sound of the recording; therefore, experiment with
dierent positions until you achieve the desired sound. To this end, you can
rotate the mic in the stand mount adapter by loosening the screw somewhat
and tightening it again.

4STUDIO CONDENSER MICROPHONE C-1 User Manual
If necessary, you can bend the microphone out of its vertical position by using the
hinge on the microphone stand.
Please make sure to handle the microphone shaft with attention and◊
care to avoid damaging the screw thread. In no situation should you
ever apply excessive force.
Of course, you can detach the C-1 from the stand mount adapter and attach it to a
commercially available suspension mount.
Audio Connection4.
Use a balanced XLR microphone cable with the following pin assignment:
pin 1 = shielding; pin 2 = +; pin 3 = -. Since your C-1 features gold-plated
contact points throughout, we recommend that you use only microphone cables
with gold-plated connectors.
Level Setting/Adjusting the Basic Sound5.
Adjust the gain control in the microphone channel of your mixing console so that
the peak LED lights up only occasionally or never at all. The EQ controls in the
microphone channel should be set to mid-travel position to start with. To get
the sound you want, try changing the mic position relative to the sound source
or even move the microphone around in the recording room of your studio.
Adjusting the angle at which walls face the sound source can also be helpful.
Only when the desired basic sound has been achieved, should you start to use
equalizers and signal processors, if any at all (remember: less is often more!)
Due to the extremely linear frequency response and the high sonic resolution of
your C-1, there is no need for high-frequency “EQing” that can heavily inuence
the signal and unnecessarily increase the noise level. The C-1 provides that
much-desired transparency which often gets lost during recording and mixing.

5STUDIO CONDENSER MICROPHONE C-1 User Manual
180° 160°
140°
1kHz
120°
100°
80°
60°
40°
20°
0 dB
-5 dB
-10 dB
-15 dB
-20 dB
-25 dB
-30 dB
-35 dB
-40 dB
0°
340°
320°
300°
280°
260°
240°
220°
200°
Polar pattern
20.0 100.0 1000.0 10k 20k Hz
dB
20.0
10.0
-10.0
-20.0
0.0
Frequency response

6STUDIO CONDENSER MICROPHONE C-1 User Manual
Specications6.
Transducer type condenser, 16 mm
Polar pattern cardioid
Connection: gold-plated balanced XLR connector
Open circuit sensitivity -33 ± 2 dBV (0 dBV = 1 V/Pa)
Frequency response 40 Hz - 20 kHz
Max. SPL (1% THD @ 1 kHz) 136 dB
Nominal impedance 100 Ω
Load impedance >1 kΩ
Mains Voltage / Fuse
Supply voltage +36 - 52 V
Supply current 2.5 mA
Physical/Weight
Dimensions Ø shaft: 54 mm
length: 169 mm
Weight approx. 0.45 kg