Belden Hirschmann SPIDER Standard Line Series User manual

Installation SPIDER-SL PoE Technical support
Release 01 05/2019 https://hirschmann-support.belden.com
User Manual
Installation
Industrial Ethernet Rail Switch
SPIDER Standard Line PoE

Installation SPIDER-SL PoE
2Release 01 05/2019
The naming of copyrighted trademarks in this manual, even when not specially indicated,
should not be taken to mean that these names may be considered as free in the sense of
the trademark and tradename protection law and hence that they may be freely used by
anyone.
© 2019 Hirschmann Automation and Control GmbH
Manuals and software are protected by copyright.All rights reserved. The copying,
reproduction, translation, conversion into any electronic medium or machine scannable form
is not permitted, either in whole or in part.An exception is the preparation of a backup copy
of the software for your own use.
The performance features described here are binding only if they have been expressly
agreed when the contract was made. This document was produced by Hirschmann
Automation and Control GmbH according to the best of the company's knowledge.
Hirschmann reserves the right to change the contents of this document without prior notice.
Hirschmann can give no guarantee in respect of the correctness or accuracy of the
information in this document.
Hirschmann can accept no responsibility for damages, resulting from the use of the network
components or the associated operating software. In addition, we refer to the conditions of
use specified in the license contract.
Hirschmann
You can get the latest version of this manual on the Internet at the Hirschmann product site
(www.hirschmann.com).
Hirschmann Automation and Control GmbH
Stuttgarter Str. 45-51
72654 Neckartenzlingen
Germany

Installation SPIDER-SL PoE
Release 01 05/2019 3
Contents
Safety instructions................................................................................4
About this Manual.................................................................................8
Legend...................................................................................................8
1 Description.......................................................................................9
1.1 General device description........................................................9
1.2 Device name and product code.................................................9
1.3 Device view.............................................................................11
1.3.1 Front view........................................................................11
1.4 Power supply...........................................................................13
1.5 Ethernet ports..........................................................................13
1.5.1 10/100/1000 Mbit/s twisted pair port................................13
1.5.2 10/100/1000 Mbit/s PoE port ...........................................13
1.5.3 10/100 Mbit/s twisted pair port.........................................14
1.5.4 10/100 Mbit/s PoE port....................................................14
1.5.5 100/1000 Mbit/s F/O port.................................................14
1.5.6 100 Mbit/s F/O port..........................................................14
1.6 Pin assignments......................................................................15
1.7 Display elements.....................................................................16
1.7.1 Power supply state..........................................................16
1.7.2 Port state.........................................................................17
1.7.3 PoE state.........................................................................17
2 Installation .....................................................................................18
2.1 Checking the package contents...............................................18
2.2 Mounting the device ................................................................19
2.2.1 Installing the device onto the DIN rail...............................19
2.2.2 Grounding the device.......................................................19
2.3 Installing an SFP transceiver (optional) ...................................20
2.4 Adjust DIP switch settings .......................................................21
2.5 Wiring the terminal block for the supply voltage and the grounding
................................................................................................22
2.6 Operating the device ...............................................................23
2.7 Connecting data cables...........................................................23
3 Monitoring the ambient air temperature......................................24
4 Maintenance and service..............................................................25
5 Disassembly ..................................................................................26
5.1 Removing an SFP transceiver (optional) .................................26
5.2 Removing the device...............................................................26
6 Technical data................................................................................27
A. Further Support.............................................................................33

Installation SPIDER-SL PoE
4Release 01 05/2019
Safety instructions
General safety instructions
You operate this device with electricity. Improper usage of the device
entails the risk of physical injury or significant property damage. The
proper and safe operation of this device depends on proper handling
during transportation, proper storage and installation, and careful
operation and maintenance procedures.
Before connecting any cable, read this document, and the safety
instructions and warnings.
Operate the device with undamaged components exclusively.
The device is free of any service components. In case of a
damaged or malfunctioning the device, turn off the supply voltage
and return the device to Hirschmann for inspection.
Certified usage
Use the product only for the application cases described in the
Hirschmann product information, including this manual.
Operate the product only according to the technical specifications.
See “Technical data” on page 27
Connect to the product only components suitable for the
requirements of the specific application case.
Installation site requirements
Install the device in a fire enclosure according to EN 60950-1.
Device casing
Only technicians authorized by the manufacturer are permitted to
open the casing.
Never insert pointed objects (narrow screwdrivers, wires, etc.) into
the device or into the connection terminals for electric conductors.
Do not touch the connection terminals.
Install the device in the vertical position.
Qualification requirements for personnel
Only allow qualified personnel to work on the device.
Qualified personnel have the following characteristics:
Qualified personnel are properly trained. Training as well as
practical knowledge and experience make up their qualifications.
This is the prerequisite for grounding and labeling circuits,
devices, and systems in accordance with current standards in
safety technology.
Qualified personnel are aware of the dangers that exist in their

Installation SPIDER-SL PoE
Release 01 05/2019 5
work.
Qualified personnel are familiar with appropriate measures
against these hazards in order to reduce the risk for themselves
and others.
Qualified personnel receive training on a regular basis.
National and international safety regulations
Verify that the electrical installation meets local or nationally
applicable safety regulations.
Grounding the device
The device is grounded by means of a separate ground screw.
Requirements for connecting electrical wires
Before connecting the electrical wires, always verify that the
requirements listed are complied with.
General requirements for connecting electrical wires
The following requirements apply without restrictions:
The electrical wires are voltage-free.
The cables used are permitted for the temperature range of the application case.
This device must be operated with a separate power supply or DC/DC converter with
galvanically separated SELV/PELV output voltages.
Requirements for connecting the supply voltage
The following requirements apply alternatively:
Alternative 1
The power supply complies with the requirements for a limited power
source as per EN 60950-1.
Alternative 2
All of the following requirements are complied with:
The power supply complies with the requirements for a safety
extra-low voltage (SELV) as per IEC/EN 60950-1.
A fuse suitable for DC voltage is located in the plus conductor of
the power supply.
The minus conductor is on ground potential. Otherwise, a fuse is
also located in the minus conductor.
Regarding the properties of this fuse:
See “General technical data” on page 27
Supply voltage
The supply voltage is only connected with the ground connection via
protective elements.

Installation SPIDER-SL PoE
6Release 01 05/2019
CE marking
The labeled devices comply with the regulations contained in the
following European directive(s):
2011/65/EU (RoHS)
Directive of the European Parliament and of the Council on the
restriction of the use of certain hazardous substances in electrical
and electronic equipment.
2014/30/EU (EMC)
Directive of the European Parliament and the council for
standardizing the regulations of member states with regard to
electromagnetic compatibility.
In accordance with the above-named EU directive(s), the EU
conformity declaration will be available to the relevant authorities at
the following address:
Hirschmann Automation and Control GmbH
Stuttgarter Str. 45-51
72654 Neckartenzlingen
Germany
The device can be used in the industrial sector.
Interference immunity: EN 61000-6-2
Emitted interference: EN 55032
You find more information on technical standards here:
“Technical data” on page 27
The assembly guidelines provided in these instructions must be
strictly adhered to in order to observe the EMC threshold values.
Warning! This is a class A device. This device can cause
interference in living areas, and in this case the operator may be
required to take appropriate measures.

Installation SPIDER-SL PoE
Release 01 05/2019 7
FCC note:
This device complies with part 15 of the FCC rules. Operation is
subject to the following two conditions: (1) this device may not cause
harmful interference; (2) this device must accept any interference
received, including interference that may cause undesired operation.
Appropriate testing has established that this device fulfills the
requirements of a class A digital device in line with part 15 of the FCC
regulations.
These requirements are designed to provide sufficient protection
against interference when the device is being used in a business
environment. The device creates and uses high frequencies and can
also radiate these frequencies. If it is not installed and used in
accordance with this operating manual, it can cause radio
transmission interference. The use of this device in a residential area
can also cause interference, and in this case the user is obliged to
cover the costs of removing the interference.
Recycling note
After usage, this device must be disposed of properly as electronic
waste, in accordance with the current disposal regulations of your
county, state, and country.

Installation SPIDER-SL PoE
8Release 01 05/2019
About this Manual
The “Installation User Manual” document contains a device description,
safety instructions, a display description and further information that you
require to install the device.
Legend
The symbols used in this manual have the following meanings:

Listing

Work step

Subheading

Installation SPIDER-SL PoE
Release 01 05/2019 9
1Description
1.1 General device description
The SPIDER-SL PoE devices are designed for the special requirements
of industrial automation. They meet the relevant industry standards,
provide very high operational reliability, even under extreme conditions,
and also long-term reliability and flexibility.
The SPIDER-SL PoE is a power sourcing equipment (PSE), provides up
to 8 Power-over-Ethernet ports. Through a twisted-pair cable connected
to the 10/100/1000 Mbit/s PoE port, the device provides power for a
powered device (PD) such as a WLAN access point, an IP camera or an
IP telephone. With the presence of the PoE power supply, a separate
power supply for the powered device is unnecessary.
You have numerous options of combining the device characteristics. You
can determine the possible combinations using the configurator which is
available in the Belden E-Catalog (www.e-catalog.beldensolutions.com)
on the web page of the device.
1.2 Device name and product code
The device name corresponds to the product code. The product code is
made up of characteristics with defined positions. The characteristic
values stand for specific product properties.
Item
Characteristic
Characteristic
value
Description
1 ... 9
Product
SPIDER-SL
SPIDER Standard Line
10
(hyphen)
-
11
Data rate
2
10/100 Mbit/s
4
10/100/1000 Mbit/s
12
Power over Ethernet
(PoE)
4
PoE+ support
13
(hyphen)
-
14 ... 17
Number
Twisted pair ports
04T1
4 ×Twisted Pair TX, RJ45
05T1
5 ×Twisted Pair TX, RJ45
08T1
8 ×Twisted Pair TX, RJ45
18 ... 19
Optical fiber port 1
M2
DSC multimode socket for
100 Mbit/s F/O connections
S2
DSC singlemode socket for
100 Mbit/s F/O connections
M4
ST multimode socket for
100 Mbit/s F/O connections
S4
ST singlemode socket for
100 Mbit/s F/O connections

Installation SPIDER-SL PoE
10 Release 01 05/2019
Item
Characteristic
Characteristic
value
Description
O6
SFP slot for 100/1000 Mbit/s
F/O connections
99
without
20 ... 21
Optical fiber port 2
O6
SFP slot for 100/1000 Mbit/s
F/O connections
99
without
22 ... 23
Optical fiber port 3
99
without
24
Temperature range
T
Extended
-40 °C ... +70 °C
(-40 °F ... +158 °F)
25 ... 26
Certificates and
declarations
Z9
CE, FCC, EN61131
27 ... 28
Customer-specific
version
HH
Hirschmann standard
29 ... 30
Configuration
HH
Hirschmann standard
Table 1: Device name and product code

Installation SPIDER-SL PoE
Release 01 05/2019 11
1.3 Device view
1.3.1 Front view
SPIDER-SL-44-05T1O6...
SPIDER-SL-44-05T199...
SPIDER-SL-44-08T19999...
SPIDER-SL-44-08T1O6O6...
Front view using example of device variants SPIDER-SL-44...
SPIDER-SL-44-05T1O6...
1
LED display elements for power supply status
2
4-pin, pluggable terminal block for power supply
3
DIP
4
LED display elements for port status
5
1 ×SFP slot for 100/1000 Mbit/s F/O connections
6
1 ×RJ45 socket for 10/100/1000 Mbit/s Twisted Pair connections
7 ... 10
4 ×RJ45 socket for 10/100/1000 Mbit/s PoE+ port
11
LED display elements for PoE status
SPIDER-SL-44-05T199...
1
LED display elements for power supply status
2
4-pin, pluggable terminal block for power supply
3
DIP
4
LED display elements for port status
5
1 ×RJ45 socket for 10/100/1000 Mbit/s Twisted Pair connections
6 ... 9
4 ×RJ45 socket for 10/100/1000 Mbit/s PoE+ port
10
LED display elements for PoE status
SPIDER-SL-44-08T19999...
1
LED display elements for power supply status
2
4-pin, pluggable terminal block for power supply
3
DIP
4
LED display elements for PoE status
5 ... 12
8 ×RJ45 socket for 10/100/1000 Mbit/s PoE+ port
SPIDER-SL-44-08T1O6O6...
1
LED display elements for power supply status
2
4-pin, pluggable terminal block for power supply
3
DIP
4
LED display elements for PoE status
5
2 ×SFP slot for 100/1000 Mbit/s F/O connections
6 ... 13
8 ×RJ45 socket for 10/100/1000 Mbit/s PoE+ port

Installation SPIDER-SL PoE
12 Release 01 05/2019
SPIDER-SL-24-04T1...
SPIDER-SL-24-05T1...
Front view using example of device variants SPIDER-SL-24...
SPIDER-SL-24-04T1...
1
LED display elements for power supply status
2
4-pin, pluggable terminal block for power supply
3
DIP
4
LED display elements for port status
5
depending on device variant
DSC multimode socket for 100 Mbit/s F/O connections
DSC singlemode socket for 100 Mbit/s F/O connections
ST multimode socket for 100 Mbit/s F/O connections
ST singlemode socket for 100 Mbit/s F/O connections
6 ... 9
4 ×RJ45 socket for 10/100 Mbit/s PoE+ port
10
LED display elements for PoE status
SPIDER-SL-24-05T1...
1
LED display elements for power supply status
2
4-pin, pluggable terminal block for power supply
3
DIP
4
LED display elements for port status
5
1 ×RJ45 socket for 10/100 Mbit/s twisted pair connections
6 ... 9
4 ×RJ45 socket for 10/100 Mbit/s PoE+ port
10
LED display elements for PoE status

Installation SPIDER-SL PoE
Release 01 05/2019 13
1.4 Power supply
You have the following options to supply your device with voltage:
Power supply via a 4-pin terminal block
For the power supply of the device, a 4-pin terminal block is
available.
For further information see “Wiring the terminal block for the supply
voltage and the grounding” on page 22.
1.5 Ethernet ports
You can connect end devices and other segments to the device ports
using twisted pair cables or optical fibers (F/O).
The PoE port of the device (Endpoint PSE) supplies voltage to the
twisted pair cables via the wire pairs carrying the signal (Alternative A)
You find information on pin assignments for making patch cables here:
“Pin assignments” on page 15
1.5.1 10/100/1000 Mbit/s twisted pair port
This port is an RJ45 socket.
The 10/100/1000 Mbit/s twisted pair port offers you the ability to connect
network components
This port supports:
Autonegotiation
Autopolarity
Autocrossing
1000 Mbit/s full duplex
100 Mbit/s half-duplex mode, 100 Mbit/s full duplex mode
10 Mbit/s half-duplex mode, 10 Mbit/s full duplex mode
1.5.2 10/100/1000 Mbit/s PoE port
This port is an RJ45 socket.
The 10/100/1000 Mbit/s PoE port allows you to connect network
components such as a powered device (PD)
This port supports:
Autonegotiation
Autopolarity
Autocrossing
1000 Mbit/s full duplex

Installation SPIDER-SL PoE
14 Release 01 05/2019
100 Mbit/s half-duplex mode, 100 Mbit/s full duplex mode
10 Mbit/s half-duplex mode, 10 Mbit/s full duplex mode
Power over Ethernet (PoE/PoE+)
1.5.3 10/100 Mbit/s twisted pair port
This port is an RJ45 socket.
The 10/100 Mbit/s twisted pair port offers you the ability to connect
network components
This port supports:
Autonegotiation
Autopolarity
Autocrossing
100 Mbit/s half-duplex mode, 100 Mbit/s full duplex mode
10 Mbit/s half-duplex mode, 10 Mbit/s full duplex mode
1.5.4 10/100 Mbit/s PoE port
This port is an RJ45 socket.
The 10/100 Mbit/s PoE port allows you to connect network components
such as a powered device (PD)
This port supports:
Autonegotiation
Autopolarity
Autocrossing
100 Mbit/s half-duplex mode, 100 Mbit/s full duplex mode
10 Mbit/s half-duplex mode, 10 Mbit/s full duplex mode
Power over Ethernet (PoE/PoE+)
1.5.5 100/1000 Mbit/s F/O port
This port is an SFP slot. The 100/1000 Mbit/s F/O port offers you the
ability to connect network components.
This port supports:
100 Mbit/s full duplex when using a Fast Ethernet SFP transceiver
1000 Mbit/s full duplex when using a Gigabit Ethernet SFP
transceiver
1.5.6 100 Mbit/s F/O port
The 100 Mbit/s F/O port offers you the ability to connect network
components.

Installation SPIDER-SL PoE
Release 01 05/2019 15
This port supports:
Full duplex mode
1.6 Pin assignments
Pin assignment of a TP/TX interface in MDI mode, RJ45 socket
RJ45
Pin
10/100 Mbit/s
1000 Mbit/s
PoE voltage
MDI mode
1
TX+
BI_DA+
Plus terminal
2
TX-
BI_DA-
Plus terminal
3
RX+
BI_DB+
Minus terminal
4
-
BI_DC+
5
-
BI_DC-
6
RX-
BI_DB-
Minus terminal
7
-
BI_DD+
8
-
BI_DD-

Installation SPIDER-SL PoE
16 Release 01 05/2019
1.7 Display elements
After the supply voltage is switched on, the device performs a self-test.
During this process, various LEDs light up.
1.7.1 Power supply state
This LED provides information on the status of the power supply.
LED
Color
Activity
Meaning
P1
Green
Lights up
The operating voltage 1 is on
None
The operating voltage 1 is off
P2
Green
Lights up
The operating voltage 2 is on
None
The operating voltage 2 is off

Installation SPIDER-SL PoE
Release 01 05/2019 17
1.7.2 Port state
These LEDs provide port-related information.
LS/DA
(link status/data)
Color
Activity
Meaning
Green
Lights up
Device detects a valid link
Flashing
Device is transmitting and/or receiving data
None
Device detects an invalid or missing link
1.7.3 PoE state
These LEDs provide information on the status of the PoE.
LED
Color
Activity
Meaning
Green
Lights up
The PoE power supply is active
None
The PoE power supply is inactive

Installation SPIDER-SL PoE
18 Release 01 05/2019
2Installation
The devices have been developed for practical application in a harsh
industrial environment.
On delivery, the device is ready for operation.
To configure a subdomain, follow these steps:
Checking the package contents
Mounting the device
Installing an SFP transceiver (optional)
Wiring the terminal block for the supply voltage and the grounding
Operating the device
Connecting data cables
2.1 Checking the package contents
Check whether the package includes all items named in the section
“Scope of delivery” on page 30.
Check the individual parts for transport damage.

Installation SPIDER-SL PoE
Release 01 05/2019 19
2.2 Mounting the device
Installing the device onto the DIN rail
2.2.1 Installing the device onto the DIN rail
Prerequisite:
The device is for mounting on a 35 mm DIN rail in accordance with DIN
EN 60715.
Proceed as follows:
Slide the upper stiff metal spring of the device into the DIN rail.
Press the device downwards onto the clip-in bar.
Snap in the device.
2.2.2 Grounding the device
The device has a functional ground connection.
The device is grounded via the separate ground screw.
Note: Ground the device before connecting any other cables.

Installation SPIDER-SL PoE
20 Release 01 05/2019
2.3 Installing an SFP transceiver (optional)
Prerequisite:
Use only Hirschmann SFP transceivers which are suitable for usage
with the device.
See “Accessories” on page 31.
Proceed as follows:
Remove the protection cap from the SFP transceiver.
Push the transceiver with the lock closed into the slot until it latches
in.