Belden HIRSCHMANN IT MAMMUTHUS MTM8000 Series User manual

User Manual
Installation
MAMMUTHUS Core-layer Switch – MTS8006-Chassis
MAMMUTHUS Power Module – MTM8000-PSU800
MAMMUTHUS Engine Module – MTM8000-Engine
MAMMUTHUS Fan Module – MTM8006-FAN
MAMMUTHUS Medium Module – MTM8000-XXXX
MAMMUTHUS Blank cover – MTM8000-XXXXCover
Install MAMMUTHUS switch
Issued in December, 2020
Technical support
https://hirschmann-it.support.belden.com

Even without specific notice, the trademark name protected by copyright in this manual shall not be
considered as being free for use by any person from the aspect of protection law for trademark and trade
name.
© 2020 Belden Singapore Pte Ltd
Both the manual and software are protected by copyright. All rights reserved. All or any part of this manual
shall be prohibited from being reproduced, copied, translated or converted into any electronic media or
machine-scannable form, except in the case that you make a copy of the software for your own use.
The performance characteristics described herein shall be binding only upon the express consent of the
parties at the time of signing the contract. This paper is produced by Belden within its capacity. Belden
reserves the right to change the contents of this manual without prior notice. Belden does not guarantee
the correctness or accuracy of the information in this manual.
Belden shall not be liable for damages caused by the use of network components or related operating
software. And the conditions of use specified in the license contract are referred to in this manual.
You may access the latest version of this manual at the product website of Hirschmann IT: Hirschmann-
it.support.belden.com.
MAMMUTHUS switch

Install MAMMUTHUS switch
Issued in December, 2020
3
Contents
Safety Guideline ................................................................................................................... 6
About this manual ............................................................................................................. 13
Legend ................................................................................................................................ 14
1 Description ................................................................................................................... 15
1.1 General device description ............................................................................... 15
1.2 Device name and product code ....................................................................... 22
1.2.1 Basic device ............................................................................................. 22
1.2.2 Power module .......................................................................................... 22
1.2.3 Engine module ......................................................................................... 22
1.2.4 Fan module .............................................................................................. 22
1.2.5 Medium module ....................................................................................... 23
1.2.6 Blank cover .............................................................................................. 24
1.3 Device view ........................................................................................................ 25
1.3.1 MTS8006-Chassis .................................................................................... 25
1.3.2 Power module .......................................................................................... 27
1.3.3 Engine module ......................................................................................... 27
1.3.4 Fan module .............................................................................................. 28
1.3.5 Medium module ....................................................................................... 28
1.3.6 Blank cover .............................................................................................. 29
1.4 Power supply ..................................................................................................... 30
1.5 Device port attribute .......................................................................................... 31
1.5.1 Console port attribute ............................................................................. 31
1.5.2 USB Console port attribute ..................................................................... 31
1.5.3 10Base-T/100Base-TX/1000Base-T RJ45 electric interface attribute .. 31
1.5.4 10GBase-T RJ45 electric interface attribute .......................................... 32
1.5.5 1000Base-X SFP optical interface attribute ........................................... 32

Install MAMMUTHUS switch
Issued in December, 2020
4
1.5.6 10GBase-SR/LR/ER SFP+ optical interface attribute ............................ 32
1.5.7 40GBase-SR4/LR4 QSFP+ optical interface attribute ........................... 32
1.5.8 USB interface attribute ............................................................................ 33
1.5.9 SD interface attribute .............................................................................. 33
1.5.10 POE interface attribute ............................................................................ 33
1.6 Display unit ........................................................................................................ 35
1.6.1 Device status ........................................................................................... 35
1.6.2 Port status ................................................................................................ 36
1.7 Management interface ....................................................................................... 38
1.7.1 DC0 interface (external management) ................................................... 38
1.7.2 USB interface ........................................................................................... 38
2 Installation .................................................................................................................... 39
2.1 Unpacking and inspection ................................................................................ 39
2.2 Install the power module (optional) ................................................................. 39
2.3 Device installation and earthing ...................................................................... 40
2.4 Install SFP transceiver (optional) ..................................................................... 42
2.5 Operate the device ............................................................................................ 44
2.6 Connecting the data cable ................................................................................ 44
2.7 Fill in the label ................................................................................................... 44
3 Carry out the basic setting ......................................................................................... 45
4 Monitor the ambient air temperature ......................................................................... 46
5 Repair and maintenance ............................................................................................. 47
6 Remove ........................................................................................................................ 48
6.1 Remove the power module ............................................................................... 48
6.2 Remove the fan module .................................................................................... 48
6.3 Remove SFP transceiver .................................................................................. 48
6.4 Remove engine or medium module ................................................................. 49
6.5 Remove the device ............................................................................................ 49

Install MAMMUTHUS switch
Issued in December, 2020
5
7 Technical data .............................................................................................................. 51
7.1 General technical data ...................................................................................... 51
7.2 Dimensional Drawing ........................................................................................ 53
7.3 EMC and interference immunity ....................................................................... 56
7.4 Network range ................................................................................................... 59
7.5 Power consumption/power output ................................................................... 59
8 Delivery item, order number and accessories .......................................................... 60
9 Basic technical criteria ............................................................................................... 62
A More support ................................................................................................................ 64

Install MAMMUTHUS switch
Issued in December, 2020
6
Safety Guideline
Warning
Uncontrolled machine action
To avoid uncontrolled machine action due to data loss, configure all data
transfer devices separately.
Before starting any machine controlled by data transfer, be sure to
complete the configuration of all data transfer devices.
Failure to comply with the
se guidelines may result in death, serious injury
or equipment damage.
 General Safety Guideline
This device shall be operated with electricity. Improper use of the device
will result in personal injury or significant property loss. Whether this
device can be properly and safely operated depends on whether the
handling process is proper, whether the storage and installation
operation are reasonable, and whether the operation and maintenance
procedures are firmly developed and strictly observed.
 Before connecting any cable, read this article, safety guideline and
warning.
 Only operate the device without any damaged component.
 Confirm that there is no component to be repaired in the device. In
case of the device damage or fault, it is required to cut off the power
supply and return the device to Belden for inspection.
 Qualification requirements for the operators
 Only the qualified person can operate this device.
The qualified personnel shall have the following features:
 The qualified personnel shall receive proper training. Training and
related practical knowledge and experience is the prerequisite for
obtaining the product operation qualification. Only when these
prerequisites are met, can the operator implement the earthing and
labeling on the circuit, device and system according to the current
safety technical standard.
 The qualified personnel shall know the danger in their work.
 The qualified personnel shall be familiar with how to handle these

Install MAMMUTHUS switch
Issued in December, 2020
7
hazards, so as to reduce the risks on themselves and other
persons.
 The qualified personnel shall receive regular training.
 Correct use
The device is only used for the intended use in the catalog and technical
description. It is only allowed to use external units and components as
recommended and allowed by the manufacturer, to operate the device.
Correct and safe operation of this product depends on correct operation,
storage, assembly and installation during the transportation, as well as
careful operation and maintenance procedures.
 National and international safety regulations
Carry out the verification, to ensure that electrical installation complies
with the local or national safety regulations.
 Requirements for the connection of electric wire
Before connecting the electric wire, make sure to always confirm
compliance with all listed requirements.
The following requirements apply, and no limitation is set:
The electric wire is voltage-free.
All cables meet the requirements for temperature range in specific application.
First, before setting other connections, connect the earthing screw on the back of the device with the
protective conductor. During the dismantling of the connection, the protective conductor shall be
finally dismantled.
During the installation, do not supply electricity to the device.
Related requirements in North American region:
Only use 60/75°C (140/167°F) or 75°C (167 °F) copper (Cu) wire.
Table 1: Requirements for the connection of electric wire
 Requirements for connection of power voltage
Device model Prerequisite:
All models Comply with all of the following requirements:
The power voltage shall be consistent with the voltage specified on the device
nameplate.
The power supply conforms to overvoltage category I or II.
The power supply is equipped with the easily operable shutoff devices (such as
switch or plug).
This shutoff device has the clear mark. In case of emergency, the operator
will be easy to know the shutoff device which corresponds to the related
power cable.
When connecting the power voltage with the protective conductor: firstly,
connect the protective conductor, then connect the power voltage.
If the device contains the second voltage connecting module of this category:
firstly, connect the protective conductor, then connect the power voltage.
DC voltage is used for power supply:
The diameter of the power line in the voltage input end of the power supply must
be at least 1mm2 (North America: AWG16).
AC voltage is used for power supply:

Install MAMMUTHUS switch
Issued in December, 2020
8
The diameter of the power line in the voltage input end of the power supply must
be at least 0.75 mm2 (North America: AWG18).
The cross section area of the earthing conductor is equal to or more than the
cross section area of the power line.
The power cable applicable for voltage, current and physical load shall be used.
The external fuse is installed in the conductor other than on the ground location.
Table 2: Requirements for connection of power voltage

9
Install MAMMUTHUS switch
Issued in December, 2020
Special conditions for safe use
Measures will be taken to prevent the instantaneous interference
exceeding 140% of the rated voltage in the voltage input end.
 Shielded earthing
The shielded earthing module of the twisted-pair cables is used as the
conductor for connection to the front panel.
When connecting the cable segment with the conductive shielding
braided layer, attention shall be paid to the possible short-circuiting.
 ESD guideline
These modules are equipped with the electrostatic sensitive
components.
In case that the connection is touched, these sensitive components are
damaged or their service life is shortened due to the electric field or load
balance effect.
You may check the information on the components with electrostatic
danger in DIN EN 61340-5-1 (2007-08) and DIN EN 61340-5-2 (2007-
08).

10
Install MAMMUTHUS switch
Issued in December, 2020
 Device enclosure
Only the technician authorized by the manufacturer can be allowed to
open the enclosure.
 Keep the air vent unblocked, to ensure good air circulation.
 Ensure that there will be he space of at least 3.94-inch (10cm) in
front of the air vent of the enclosure.
 During the operation or shortly after the shutdown of the device, do
not touch the enclosure. Hot surface will cause any possible
damage. Install the device horizontally in the machine cabinet or
vertically on the flat surface.
Do not place the device on the tabletop for operation. Refer to
"Device Installation and Earthing" on Page 38.
 Operate the device in the maximum ambient air temperature and
stacking device: when installing the device, ensure that there is at
least the space available for the machine frame (about 5cm) above
the device, to facilitate smooth discharge of heat out of the device
enclosure.
 If you operate the device in the 19" switch cabinet: install the
slide/install guide rail to support the weight of the device.
 Requirements for the installation station
This device can only be operated at the specified ambient temperature-
ambient air temperature at 2 inch (5cm) away from the device- and at
relative humidity.
 When choosing the installation position, ensure the compliance with
climatic threshold as stipulated in the technical data.
 This device is used in the environment that the maximum pollution
class conforms to the technical data code.