Belden Hirschmann RS20 Series User manual

Installation RS20/22/30/32/40
Release 07 10/2021
Technical support
https://hirschmann-support.belden.com
User Manual
Installation
Industrial ETHERNET Rail Switch
RS20/RS22/RS30/RS32/RS40 Family
RS30-0802...
RS30
RM
+24V(P1) 0V 0V
FAULT
+24V(P2)
Stand by
Aufkleber MAC-Adresse
IP-ADDRESS
3
5
7
9
4
6
8
10
V.24
USB
P
Stand by
FAULT
RM
ON
LS
2
DA
LS
1
DA
RS30-1602...
RS20
+24V(P1) 0V 0V
FAULT
+24V(P2)
4
6
8
5
7
9
LS DA
2
LS DA
1
LS DA
3
RS30
+24V(P1) 0V 0V
FAULT
+24V(P2)
5
7
9
11
6
8
10
12
13
15
17
14
16
18
LS DA
1
LS DA
2
LS DA
3
LS DA
4
RS20
LS DA
RM
+24V(P1) 0V 0V
FAULT
+24V(P2)
Stand by
Aufkleber MAC-Adresse
IP-ADDRESS
3
5
7
9
11
13
15
17
2
LS DA
1
4
6
8
10
12
14
16
18
19
21
23
20
22
24
V.24
USB
P
Stand by
FAULT
RM
ON
RS20
LS DA
RM
+24V(P1) 0V 0V
FAULT
+24V(P2)
Stand by
Aufkleber MAC-Adresse
IP-ADDRESS
2
LS DA
1
3
5
7
4
6
8
V.24
USB
P
Stand by
FAULT
RM
ON
RS20
RM
Stand by
Aufkleber MAC-Adresse
IP-ADDRESS
V.24
USB
P
Stand by
FAULT
RM
ON
LS
1
DA
LS
2
DA
LS
3
DA
LS
4
DA
RS20-0800...RS20-2400... RS20-0400...
RM
Stand by
Aufkleber MAC-Adresse
IP-ADDRESS
V.24
USB
P
Stand by
FAULT
RM
ON
RM
Stand by
Aufkleber MAC-Adresse
IP-ADDRESS
V.24
USB
P
Stand by
FAULT
RM
ON
RS20-0900...
RS40
+24V(P1) 0V 0V
FAULT
+24V(P2)
1
3
5
7
2
4
6
8
1
2
3
4
RM
Stand by
Aufkleber MAC-Adresse
IP-ADDRESS
V.24
USB
P
Stand by
FAULT
RM
ON
9
RS40-0009... RS32-0802... RPS90/48V HV
RPS90/48V HV
U: 110 / 230 VAC
U: 60 / 250 VDC
-/N
+/L
0V
+48V / 1,9A
48-54V
P
RS32
1
GB
2
GB
RM
Stand by
Aufkleber MAC-Adresse
IP-ADDRESS
V.24
USB
P
Stand by
FAULT
RM
ON
LS DA
LS DA
3
5
7
9
4
6
8
10
+24V(P1) 0V 0V
FAULT
+24V(P2)
FAULT
+48V(P1) 0V 0V +48V(P2)

2021-10-29 Installation RS20/22/30/32/40
Release 07 10/2021
The naming of copyrighted trademarks in this manual, even when not specially indicated, should
not be taken to mean that these names may be considered as free in the sense of the trademark
and tradename protection law and hence that they may be freely used by anyone.
© 2021 Hirschmann Automation and Control GmbH
Manuals and software are protected by copyright. All rights reserved. The copying, reproduction,
translation, conversion into any electronic medium or machine scannable form is not permitted,
either in whole or in part. An exception is the preparation of a backup copy of the software for
your own use.
The performance features described here are binding only if they have been expressly agreed
when the contract was made. This document was produced by Hirschmann Automation and
Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right
to change the contents of this document without prior notice. Hirschmann can give no guarantee
in respect of the correctness or accuracy of the information in this document.
Hirschmann can accept no responsibility for damages, resulting from the use of the network
components or the associated operating software. In addition, we refer to the conditions of use
specified in the license contract.
You can get the latest version of this manual on the Internet at the Hirschmann product site
(www.hirschmann.com).
Hirschmann Automation and Control GmbH
Stuttgarter Str. 45-51
72654 Neckartenzlingen
Germany

Installation RS20/22/30/32/40
Release 07 10/2021 3
Contents
Important information 5
Safety instructions 7
About this Manual 20
Key 21
1 Description 22
1.1 Description of the device variants 23
1.1.1 Combination options of the device variants RS20/
RS30/RS22/RS32 24
1.1.2 Combination options for the RS40 device variants 27
1.1.3 Number of ports and media for RS20-... 29
1.1.4 Number of ports and media for RS30-... 32
1.1.5 Number of ports and media for RS40-... 35
1.2 Device variants with PoE (optional) 36
1.2.1 Number of ports and media for devices with PoE 36
1.2.2 PoE power units 38
1.3 Ethernet ports 38
1.3.1 10/100/1000 Mbit/s twisted pair port 38
1.3.2 10/100 Mbit/s twisted pair port 39
1.3.3 10/100 Mbit/s twisted-pair connection PoE
(RS22-.../RS32-...) 40
1.3.4 1000 Mbit/s F/O port 40
1.3.5 100 Mbit/s F/O port 41
1.3.6 Gigabit combo port 41
1.4 Display elements 42
1.5 Management interfaces 44
1.5.1 USB interface 44
1.5.2 V.24 interface (external management) 44
2 Installation 46
2.1 Checking the package contents 47
2.2 Installing and grounding the device 47
2.2.1 Installing the device onto the DIN rail 47

4Installation RS20/22/30/32/40
Release 07 10/2021
2.2.2 DIN rail mounting on ships (RS30-0802...) 48
2.2.3 Mounting on a vertical flat surface 49
2.2.4 Grounding the device 50
2.3 Installing an SFP transceiver (optional) 51
2.4 Adjust DIP switch settings 51
2.5 Connecting the terminal block 52
2.5.1 RS20/RS30/RS40: supply voltage and signal contact 53
2.5.2 RS22/RS32: supply voltage and signal contact 54
2.6 Mounting the terminal block 57
2.7 Connecting the ferrite 57
2.8 Operating the device 58
2.9 Connecting data cables 58
2.10 Filling out the inscription label 58
3 Making basic settings 59
3.1 Applies to devices with a software version before HiOS 7.1/
8.1 59
3.1.1 Default settings 59
4 Monitoring the ambient air temperature 60
5 Maintenance and service 61
6Disassembly 62
6.1 Removing the device 62
6.2 Removing an SFP transceiver (optional) 63
7 Technical data 64
A Further support 81

Installation RS20/22/30/32/40
Release 07 10/2021 5
Important information
Note: Read these instructions carefully, and familiarize yourself with the
device before trying to install, operate, or maintain it. The following notes may
appear throughout this documentation or on the device. These notes warn of
potential hazards or call attention to information that clarifies or simplifies a
procedure.
Symbol explanation
This is a general warning symbol. This symbol alerts you to
potential personal injury hazards. Observe all safety notes that
follow this symbol to avoid possible injury or death.
If this symbol is displayed in addition to a safety instruction of the
type “Danger” or “Warning”, it means that there is a danger of
electric shock and failure to observe the instructions will
inevitably result in injury.
This symbol indicates the danger of hot surfaces on the device.
In connection with safety instructions, non-observance of the
instructions will inevitably result in injuries.
DANGER
DANGER draws attention to an immediately dangerous situation, which will
inevitably result in a serious or fatal accident if not observed.
WARNING
WARNING indicates a potentially hazardous situation which, if not avoided,
could result in death or serious injury.
CAUTION
CAUTION indicates a possible danger which, if not avoided, may result in
minor injuries.

6Installation RS20/22/30/32/40
Release 07 10/2021
NOTICE
NOTE provides information about procedures that do not involve the risk of
injury.

Installation RS20/22/30/32/40
Release 07 10/2021 7
Safety instructions
General safety instructions
You operate this device with electricity. Improper usage of the device
entails the risk of physical injury or significant property damage. The
proper and safe operation of this device depends on proper handling
during transportation, proper storage and installation, and careful
operation and maintenance procedures.
Before connecting any cable, read this document, and the safety
instructions and warnings.
Operate the device with undamaged components exclusively.
The device is free of any service components. In case of a damaged
or malfunctioning device, turn off the supply voltage and return the
device to Hirschmann for inspection.
Certified usage
Use the device solely for the application cases described in the
Hirschmann product information, including this manual.
Operate the device solely according to the technical specifications.
See “Technical data” on page 64.
Installation site requirements
Install the device in a fire enclosure according to IEC 60950-1.
If installed in a living area or office environment, the device must be
operated only in switch cabinets with fire protection characteristics
according to IEC 60950-1.
Only when using the PoE power supply unit RPS90/48V HV:
Install this device only in a switch cabinet or in an operating site with
restricted access, to which maintenance staff have exclusive access.
WARNING
UNCONTROLLED MACHINE ACTIONS
To avoid uncontrolled machine actions caused by data loss, configure all
the data transmission devices individually.
Before you start any machine which is controlled via data transmission, be
sure to complete the configuration of all data transmission devices.
Failure to follow this instruction can result in death, serious injury, or
equipment damage.

8Installation RS20/22/30/32/40
Release 07 10/2021
Strain relief
Note: If the strain relief is insufficient, there is a potential risk of torsion,
contact problems and creeping interruptions.
Relieve the connection points of cables and lines from mechanical
stress.
Design strain reliefs in such a way that they help prevent any
mechanical damage to cables, wires or conductors caused by external
influences or their own weight.
To help prevent damage to device connections, connectors and
cables, follow the instructions for proper installation in accordance with
DIN VDE 0100-520:2013-06, sections 522.6, 522.7 and 522.13.
Device casing
Only technicians authorized by the manufacturer are permitted to open
the casing.
Never insert pointed objects (narrow screwdrivers, wires, etc.) into the
device or into the connection terminals for electric conductors. Do not
touch the connection terminals.
Keep the ventilation slits free to ensure good air circulation.
See “General technical data” on page 64.
Mount the device in the vertical position.
At ambient air temperatures > +60 °C (+140 °F):
The surfaces of the device housing may become hot. Avoid touching
the device while it is operating.
Qualification requirements for personnel
Only allow qualified personnel to work on the device.
Qualified personnel have the following characteristics:
Qualified personnel are properly trained. Training as well as practical
knowledge and experience make up their qualifications. This is the
prerequisite for grounding and labeling circuits, devices, and systems
in accordance with current standards in safety technology.
Qualified personnel are aware of the dangers that exist in their work.
Qualified personnel are familiar with appropriate measures against
these hazards in order to reduce the risk for themselves and others.
Qualified personnel receive training on a regular basis.
National and international safety regulations
Verify that the electrical installation meets locally or nationally applicable
safety regulations.

Installation RS20/22/30/32/40
Release 07 10/2021 9
Grounding the device
The device is grounded via the separate ground screw on the bottom left
of the front side of the device.
Use a wire diameter for the ground conductor that is no smaller than
the diameter of the supply voltage connection, however of at least 1.0
mm² (AWG16).
Ground the device before connecting any other cables.
Disconnect the grounding only after disconnecting all other cables.
Shielding ground
The overall shield of a connected shielded twisted pair cable is connected
to the grounding connector on the front panel as a conductor.
Beware of possible short circuits when connecting a cable section with
conductive shielding braiding.
Supply voltage
The supply voltage is electrically isolated from the housing.
The devices are designed for operation with Safety Extra-low Voltage
(SELV). Connect only SELV circuits with voltage restrictions according
to IEC 60950-1 or ES1 according to IEC/EN 62368-1 to the supply
voltage connections and to the signal contacts.
Exclusively connect a supply voltage that corresponds to the type
plate of your device.
Applies exclusively to RS20-..., RS30-..., RS40-... device variants:
For power supply via DC voltage: All following prerequisites are
fulfilled:
There are fuses suitable for DC voltage in the positive conductors
of the supply lines, or the voltage sources are appropriately current-
limited. Regarding the properties of this fuse: See “General
technical data” on page 64.
The negative conductors of the voltage inputs are on ground
potential.
For power supply via AC voltage: All following prerequisites are
fulfilled:
There are fuses in the supply lines, or the voltage sources are
appropriately current-limited. Regarding the properties of this fuse:
See “General technical data” on page 64.
The power sources are electrically isolated from the ground
potential.

10 Installation RS20/22/30/32/40
Release 07 10/2021
Applies exclusively to RS22-..., RS32-... device variants:
All of the following requirements are complied with:
There are fuses suitable for DC voltage in the positive conductors
of the supply lines, or the voltage sources are appropriately current-
limited. Regarding the properties of this fuse: See “Technical data”
on page 64.
The power sources are electrically isolated from the ground
potential. According to specification IEEE 802.3, the insulation
voltage must be 1500 V AC or 2250 V DC.
Observe the maximum values for the contact load of the signal
contact.
Relevant for North America:
The device may only be connected to a Class 2 supply voltage that
fulfills the requirements of the National Electrical Code, Table 11(b). If
the voltage is being supplied redundantly (two different voltage
sources), the combined supply voltages must fulfill the requirements of
the National Electrical Code, Table 11(b).
Relevant for North America: For use in class 2 circuits.
Use 60/75 °C (140/167 °F) or 75 °C (167 °F) copper (Cu) wire only.
Relevant for North America
for devices certified for hazardous locations:
Power, input and output (I/O) wiring must be in accordance with
Class I, Division 2 wiring methods [Article 501-4(b) of the National
Electrical Code, NFPA 70] and in accordance with the authority having
jurisdiction.
Start connecting the electrical wires only if all the above safety
requirements are fulfilled.
Enable the supply voltage for the device only when the following
requirements are fulfilled:
the housing is closed
the terminal blocks are wired correctly
the terminal blocks for the power supply are connected
Internal fuses are triggered only in the case of a detected error in the
device. In case of damage or malfunction of the device, turn off the
supply voltage and return the device to the plant for inspection.