Belden Hirschmann SPIDER II 8TX User manual

SPIDER II
Release 04 09/09 Technical Support [e-mail]
User Manual
Installation
Industrial ETHERNET Rail Switch
SPIDER II, SPIDER II Giga, SPIDER II PoE
SPIDER II 8TX
SPIDER II 8TX EEC
SPIDER II 8TX/1FX EEC
SPIDER II 8TX/1FX-SM EEC
SPIDER II 8TX/1FX-ST EEC
SPIDER II 8TX/2FX EEC
SPIDER II 8TX/2FX-SM EEC
SPIDER II 8TX/2FX-ST EEC SPIDER II Giga 5T/2S EEC SPIDER II Giga 5T EEC
SPIDER II 8TX PoE
SP
SP
SP
SP
SP
SP
SP
SP
SP
SP
P
1
2
3
4
5
6
7
8

The naming ofcopyrighted trademarks inthis manual,even when not specially indicated, should
not be taken to mean that these names may be considered as free in the sense of the trademark
and tradename protection law and hence that they may be freely used by anyone.
© 2009 Hirschmann Automation and Control GmbH
Manualsandsoftwareareprotectedby copyright.Allrightsreserved.Thecopying,reproduction,
translation, conversion into any electronic medium or machine scannable form is not permitted,
either in whole or in part. An exception is the preparation of a backup copy of the software for
your own use. For devices with embedded software, the end-user license agreement on the en-
closed CD applies.
The performance features described here are binding only if they have been expressly agreed
when the contract was made. This document was produced by Hirschmann Automation and
ControlGmbHaccordingto thebestofthecompany'sknowledge.Hirschmannreservestheright
to change the contents of this document without prior notice. Hirschmann can give no guarantee
in respect of the correctness or accuracy of the information in this document.
Hirschmann can accept no responsibility for damages, resulting from the use of the network
components or the associated operating software. In addition, we refer to the conditions of use
specified in the license contract.
You can get the latest version of this manual on the Internet at the Hirschmann product site
(www.hirschmann-ac.de).
Printed in Germany
Hirschmann Automation and Control GmbH
Stuttgarter Str. 45-51
72654 Neckartenzlingen
Germany
Tel.: [phone]
039 709-001-04-0909 17.9.09

SPIDER II
Release 04 09/09 3
Content
Safety instructions 4
Legend 8
1 Device description 9
1.1 Description of the device variants 10
2 Assembly and start-up 14
2.1 Installing the device 14
2.1.1 Unpacking and checking 14
2.1.2 Installing the SFP modules (if present) 15
2.1.3 Connecting the terminal block for the supply voltage
and the grounding 15
2.1.4 Mounting the device on the DIN rail 16
2.1.5 Dimensions 17
2.1.6 Installing the terminal block, start-up procedure 17
2.1.7 Connecting the data lines 17
2.2 Display elements 20
2.2.1 Device state 20
2.2.2 Port state 20
2.3 Disassembly 21
2.3.1 Removing the device from the DIN rail 21
2.3.2 Disassembling the SFP modules 22
3 Technical data 23
Further support 28

4SPIDER II
Release 04 09/09
Safety instructions
Notes on safety
This manual contains instructions to be observed for ensuring your per-
sonal safety and for preventing damage. The warnings appear next to a
warning triangle with a different heading depending on the degree of dan-
ger posed:
Danger!
Means that death, serious physical injury or significant damage
to property will occur if the corresponding safety measures are
not carried out.
Warning!
Means that death, serious physical injury or significant damage
to property could occur if the corresponding safety measures
are not carried out.
Caution!
Means that minor physical injury or damage to property can oc-
cur if the required safety measures are not carried out.
Note: Contains important information on the product, on how to manage
the product, or on the respective section of the documentation to which
your special attention is being drawn.
Certified usage
Please observe the following: The device may only be employed for the
purposes described in the catalog and technical description, and only in
conjunction with external devices and components recommended or
approved by the manufacturer. The product can only be operated cor-
rectly and safely if it is transported, stored, installed and assembled pro-
perly and correctly. Furthermore, it must be operated and serviced
carefully.
Supply voltage
The devices are designed for operation with a safety extra-low voltage.
Accordingly, only SELV circuits with voltage restrictions in line with IEC/
EN 60950-1 may be connected to the supply voltage connections.
Warning!
Only connect asupply voltagethat corresponds tothe type plate
of your device.
Use only undamaged parts.

SPIDER II
Release 04 09/09 5
If you are operating the module with an external voltage, only supply
the system with a safety extra-low voltage in compliance with IEC/EN
60950-1.
Connect the ground connector before you set up the other connec-
tions. When removing the connections, you remove the ground con-
nector last.
Relevant for North America: To be used in class 2 circuits.
The device may only be connected to a supply voltage of class 2 that
fulfills the requirements of the National Electrical Code, Table 11(b).
Relevant for North America: For use in Class 2 circuits.
Only use copper wire/conductors of class 1, 60/75°C or 90 °C.
Relevant for North America
for devices certified for hazardous locations:
Power, input and output (I/O) wiring must be in accordance with
Class I, Division 2 wiring methods [Article 501-4(b) of the National
ElectricalCode,NFPA 70]andin accordance withtheauthorityhaving
jurisdiction.
Only switch on the device when the housing is closed.
Shielding ground
Bewareofpossible shortcircuitswhen connecting a cablesectionwith
conductive shielding braiding.
Housing
Only technicians authorized by Hirschmann are permitted to open the
housing.
Note: The device is grounded by means of a 3-pin terminal block.
Make sure that the electrical installation meets local or nationally ap-
plicable safety regulations.
The ventilation slits must not be covered so as to ensure free air circu-
lation.
The clearance to the ventilation slits of the housing must be at least
10 cm (3.94 in).
The device must be installed in the vertical position.
If installed in aliving areaor officeenvironment, the devicemust beop-
eratedexclusivelyinswitchcabinetswithfireprotectioncharacteristics
in accordance with EN 60950-1.

6SPIDER II
Release 04 09/09
Warning!
Never insert sharp objects (small screwdrivers, wires, etc.) into
the inside of the product. There is the risk of an electric shock.
Environment
The device may only be operated at the specified maximum ambient tem-
perature (temperature of the ambient air at a distance of up to 5 cm (1.97
in) from the device) and relative air humidity.
Install the device in a location where the climatic threshold values
specified in the technical data are adhered to.
Only to be used in an environment with the contamination level speci-
fied in the technical data.
Qualification requirements for personnel
Qualified personnel as understood in this manual and the warning signs,
are persons who are familiar with the setup, assembly, startup, and oper-
ation of this product and are appropriately qualified for their job. This in-
cludes, for example, those persons who have been:
Xtrained or directed or authorized to switch on and off, to ground and to
labelpowercircuitsanddevicesorsystems in accordance withcurrent
safety engineering standards;
Xtrainedordirectedinthe careand useof appropriatesafetyequipment
in accordance with the current standards of safety engineering;
Xtrained in providing first aid.
General safety instructions
Electricity is used to operate this equipment. Comply in every detail with
the safety requirements specified in the operating instructions regarding
the voltages to apply (refer to page 4).
Non-observance of thesesafetyinstructionscanthereforecausematerial
damage and/or serious injuries.
Only appropriately qualified personnel should work on this device or in
its vicinity. These personnel must be thoroughly familiar with all the
warnings and maintenance procedures in accordance with this oper-
ating manual.
The proper and safe operation of this device depends on proper han-
dling during transport, proper storage and assembly, and conscien-
tious operation and maintenance procedures.
Never start operation with damaged components.
Only use the devices in accordance with this manual. In particular, ob-
serve all warnings and safety-related information.
Any work that may be required on the electrical installation may only
be carried out by personnel trained for this purpose.

SPIDER II
Release 04 09/09 7
Relevant for SPIDER II 8 TX/...FX... EEC and SPIDER II Giga 5T/2S
EEC:
Note:
LED or LASER components in compliance with IEC 60825-1 (2001):
CLASS 1 LASER PRODUCT
CLASS 1 LED PRODUCT
National and international safety regulations
Make sure that the electrical installation meets local or nationally
applicable safety regulations.
Note on the CE marking
The devices comply with the regulations contained in the following Euro-
pean directive(s):
2006/95/EG, 2004/108/EG
Directive of the European Parliament and the council for standardizing
the regulations of member states with regard to electromagnetic
compatibility.
72/245/EWG, 2006/28/EG
Guideline for standardizing the regulations of member states relating to
radio interference from motor vehicles. Certified devices are marked with
an e1 type approval indicator.
In accordance with the above-named EU directive(s), the EU conformity
declaration will be at the disposal of the relevant authorities at the follow-
ing address:
Hirschmann Automation and Control GmbH
Stuttgarter Str. 45-51
72654 Neckartenzlingen
Tel.: [phone]
The product can be used in living areas (living area, place of business,
small business) and in industrial areas.
XInterference immunity: EN 61000-6-2:2005
XEmitted interference: EN 55022:2006 Class A

8SPIDER II
Release 04 09/09
Warning
This is a class A device. This device can cause interference in
living areas, and in this case the operator may be required to
take appropriate measures.
The assembly guidelines provided in these instructions must be strictly
adhered to in order to observe the EMC threshold values.
FCC note:
Appropriate testing has established that this device fulfills the require-
ments of a class A digital device in line with part 15 of the FCC regula-
tions.
These requirements are designed to provide sufficient protection against
interference when the device is being used in a business environment.
The device creates and uses highfrequencies and can radiate same, and
if it is not installed and used in accordance with this operating manual, it
can cause radio transmission interference. The use of this device in a liv-
ing area can also cause interference, and in this case the user is obliged
to cover the costs of removing the interference.
Recycling note
Afterusage,thisproductmustbedisposedofproperlyas electronicwaste
in accordance with the current disposal regulations of your county / state
/ country.
Legend
The commendations used in this manual have the following meanings:
XListing
Work step
Subheading

SPIDER II
Release 04 09/09 9
1 Device description
The SPIDER II devices are designed for the special requirements of industri-
al automation. They meet the relevant industry standards, provide very high
operational reliability, even under extreme conditions, and also long-term re-
liability and flexibility.
The devices allow you to set up switched industrial ETHERNET networks
that conform to the IEEE 802.3 and 802.3u standards using copper wires or
optical fibers in a line structure.
The SPIDER II 8TX... devices have, depending on the variant, eight TP ports
(10/100 Mbit/s, RJ45 socket) and up to two 100 Mbit/s F/O ports (100BASE-
FX, DSC or ST connection). The SPIDER II Giga... devices have, depending
on the variant, five TP ports (10/100/1000 Mbit/s, RJ45 socket) and up to two
1000 Mbit/s F/O ports (1000BASE-SX/LX, SFP slot).
The SPIDER II 8TX PoE devices support Power over ETHERNET (PoE) ac-
cording to IEEE 802.3af.
They allow the connection and remote supply of, for example, IP telephones
(Voice over IP), webcams, sensors, printer servers and WLAN access points
via 10BASE-T/100BASE-TX. With PoE, these terminal devices are powered
by the twisted-pair cable.
Mount the devices by
Xsimply snapping them onto a DIN rail
Depending on the device variant, you can choose various media to connect
terminal devices and other infrastructure components:
Xtwisted pair cable
Xmultimode F/O
Xsinglemode F/O
The twisted pair ports support:
XAutocrossing
XAutonegotiation
XAutopolarity
The F/O ports support:
XFull duplex mode
The Hirschmann network components help you to establish continuous com-
munication across all levels of the company. Connect your devices to:
Xdevices of the MICE family
Xbackbone devices of the MICE family
Xthe BAT wireless transmission system
Xthe EAGLE security system
Xproducts for the LION control room / MACH 100 family

10 SPIDER II
Release 04 09/09
1.1 Description of the device variants
The devices differ with regard to the number of interfaces and the media type
for connecting segments.
The table below shows the number and type of the ports for each product
variant. The abbreviations F/O (optical fiber) and TP (twisted pair) indicate
the media type. The abbreviations DSC, ST, SFP and RJ45 indicate the
socket type. The abbreviations MM (Multimode) and SM (Singlemode) indi-
cate the optical fiber type.
Variant
10/100 Mbit/s, TP, RJ45 PoE ports included 100 Mbit/s, F/O, MM, DSC 100 Mbit/s, F/O, SM, DSC 100 Mbit/s, F/O, MM, ST 10/100/ 1000 Mbit/s, TP, RJ45 1000 Mbit/s, F/O, SFP
SPIDER II 8TX 8
SPIDER II 8TX EEC 8
SPIDER II 8TX/1FX EEC 8 1
SPIDER II 8TX/1FX-SM EEC 8 1
SPIDER II 8TX/2FX EEC 8 2
SPIDER II 8TX/2FX-SM EEC 8 2
SPIDER II 8TX/1FX-ST EEC 8 1
SPIDER II 8TX/2FX-ST EEC 8 2
SPIDER II Giga 5T EEC 5
SPIDER II Giga 5T/2S EEC 5 2
SPIDER II 8TX PoE 4
Table 1: Number and type of ports