Belden Hirschmann DRAGON MACH Series User manual

Installation DRAGON MACH Family
Release 04 02/2021
Technical support
https://hirschmann-support.belden.com
User Manual
Installation
Modular Industrial Gigabit Ethernet Backbone Switch
DRAGON MACH Family

05.02.2021 Installation DRAGON MACH Family
Release 04 02/2021
The naming of copyrighted trademarks in this manual, even when not specially indicated, should
not be taken to mean that these names may be considered as free in the sense of the trademark
and tradename protection law and hence that they may be freely used by anyone.
© 2021 Hirschmann Automation and Control GmbH
Manuals and software are protected by copyright. All rights reserved. The copying, reproduction,
translation, conversion into any electronic medium or machine scannable form is not permitted,
either in whole or in part. An exception is the preparation of a backup copy of the software for
your own use.
The performance features described here are binding only if they have been expressly agreed
when the contract was made. This document was produced by Hirschmann Automation and
Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right
to change the contents of this document without prior notice. Hirschmann can give no guarantee
in respect of the correctness or accuracy of the information in this document.
Hirschmann can accept no responsibility for damages, resulting from the use of the network
components or the associated operating software. In addition, we refer to the conditions of use
specified in the license contract.
You can get the latest version of this manual on the Internet at the Hirschmann product site
(www.hirschmann.com).
Hirschmann Automation and Control GmbH
Stuttgarter Str. 45-51
72654 Neckartenzlingen
Germany

Installation DRAGON MACH Family
Release 04 02/2021 3
Contents
Important information 7
Safety instructions 9
About this Manual 16
Key 17
1 Description 18
1.1 General device description 18
1.1.1 Basic device 18
1.1.2 Media modules 19
1.1.3 Power supply unit module 19
1.1.4 Fan module 20
1.2 Device views 21
1.2.1 Media modules 24
1.2.2 Power supply unit module 25
1.2.3 Fan module 25
1.3 Power supply 26
1.3.1 Power supply modules 26
1.3.2 Media module D4K-10TP-PoE 28
1.4 Signal contact 29
1.5 Ethernet ports 30
1.5.1 10/100/1000 Mbit/s twisted pair port 30
1.5.2 100/1000 Mbit/s F/O port 31
1.5.3 1/2.5/10 Gbit/s F/O port 31
1.5.4 Support of PoE 31
1.5.5 Out-of-band management port 32
1.6 Display elements 33
1.6.1 Device state 33
1.6.2 PSU module status 37
1.6.3 Port status 38
1.6.4 Management interface status 39
1.6.5 Media module status 40
1.7 Management interfaces 43

4Installation DRAGON MACH Family
Release 04 02/2021
1.7.1 V.24 interface (external management) 43
1.7.2 USB interface 44
1.7.3 SD card interface 45
2 Installation 46
2.1 Checking the package contents 46
2.2 Installing the SD card (optional) 47
2.3 Installing a cover panel (optional) 48
2.4 Installing a power supply module 49
2.5 Installing a media module (optional) 50
2.6 Mounting the fan module 51
2.7 Installing and grounding the device 52
2.8 Wiring and mounting the signal contact (optional) 54
2.9 Connecting the supply voltage 56
2.9.1 Power supply modules 56
2.9.2 Media module D4K-10TP-PoE 58
2.10 Installing an SFP transceiver (optional) 59
2.11 Operating the device 59
2.12 Connecting data cables 60
3 Making basic settings 61
4 Monitoring the ambient air temperature 63
5 Maintenance and service 64
6Disassembly 65
6.1 De-installing a power supply module 65
6.2 Removing a fan module 66
6.3 Removing a media module 67
6.4 Removing an SFP transceiver (optional) 68
6.5 Removing the device 68
7 Technical data 69
7.1 General data 69
7.1.1 Basic device 69

Installation DRAGON MACH Family
Release 04 02/2021 5
7.1.2 Power supply unit module 69
7.1.3 Fan module 69
7.1.4 Media modules 69
7.2 Supply voltage 70
7.2.1 Power supply modules 70
7.2.2 Media module D4K-10TP-PoE 70
7.3 Signal contact 71
7.4 Power consumption/power output 71
7.5 Climatic conditions during operation 72
7.6 Climatic conditions during storage 72
7.7 Dimension drawings 73
7.7.1 Basic device 73
7.7.2 Power supply unit module 74
7.7.3 Fan module 74
7.7.4 Media modules 75
7.8 EMC and immunity 76
7.9 Network range 77
7.9.1 10/100/1000 Mbit/s twisted pair port 77
7.9.2 Fast Ethernet SFP transceiver 77
7.9.3 Bidirectional Fast Ethernet SFP transceiver 78
7.9.4 Gigabit Ethernet SFP transceiver 79
7.9.5 Bidirectional Gigabit Ethernet SFP transceiver 80
7.9.6 2.5 Gigabit Ethernet SFP transceiver 81
7.9.7 10 Gigabit Ethernet SFP+ transceiver 82
8 Scope of delivery 83
8.1 Basic device 83
8.2 Media modules 83
8.3 Power supply units 83
8.4 Fan module 83
9 Order numbers 84
10 Accessories 85

6Installation DRAGON MACH Family
Release 04 02/2021
11 Underlying technical standards 88
A Further support 89

Installation DRAGON MACH Family
Release 04 02/2021 7
Important information
Note: Read these instructions carefully, and familiarize yourself with the
device before trying to install, operate, or maintain it. The following notes may
appear throughout this documentation or on the device. These notes warn of
potential hazards or call attention to information that clarifies or simplifies a
procedure.
Symbol explanation
This is a general warning symbol. This symbol alerts you to
potential personal injury hazards. Observe all safety notes that
follow this symbol to avoid possible injury or death.
If this symbol is displayed in addition to a safety instruction of the
type “Danger” or “Warning”, it means that there is a danger of
electric shock and failure to observe the instructions will
inevitably result in injury.
This symbol indicates the danger of hot surfaces on the device.
In connection with safety instructions, non-observance of the
instructions will inevitably result in injuries.
DANGER
DANGER draws attention to an immediately dangerous situation, which will
inevitably result in a serious or fatal accident if not observed.
WARNING
WARNING indicates a potentially hazardous situation which, if not avoided,
could result in death or serious injury.
CAUTION
CAUTION indicates a possible danger which, if not avoided, may result in
minor injuries.

8Installation DRAGON MACH Family
Release 04 02/2021
NOTICE
NOTE provides information about procedures that do not involve the risk of
injury.

Installation DRAGON MACH Family
Release 04 02/2021 9
Safety instructions
General safety instructions
You operate this device with electricity. Improper usage of the device
entails the risk of physical injury or significant property damage. The
proper and safe operation of this device depends on proper handling
during transportation, proper storage and installation, and careful
operation and maintenance procedures.
Before connecting any cable, read this document, and the safety
instructions and warnings.
Operate the device with undamaged components exclusively.
The device is free of any service components. In case of a damaged
or malfunctioning device, turn off the supply voltage and return the
device to Hirschmann for inspection.
Correct usage
Only use the device for those purposes specified in the catalog and in the
technical description. Only operate the device with external devices and
components that are recommended and permitted by the manufacturer.
The proper and safe operation of this product depends on proper handling
during transport, proper storage, assembly and installation, and
conscientious operation and maintenance procedures.
National and international safety regulations
Verify that the electrical installation meets local or nationally applicable
safety regulations.
WARNING
UNCONTROLLED MACHINE ACTIONS
To avoid uncontrolled machine actions caused by data loss, configure all
the data transmission devices individually.
Before you start any machine which is controlled via data transmission, be
sure to complete the configuration of all data transmission devices.
Failure to follow these instructions can result in death, serious injury,
or equipment damage.

10 Installation DRAGON MACH Family
Release 04 02/2021
Installation site requirements
Operate the device at the specified ambient temperature (temperature of
the ambient air at a distance of 2 in (5 cm) from the device) and at the
specified relative humidity exclusively.
When you are selecting the installation location, make sure you
observe the climatic threshold values specified in the technical data.
Use the device in an environment with a maximum pollution degree
that complies with the specifications in the technical data.
Strain relief
Note: If the strain relief is insufficient, there is a risk of torsion, contact
problems and creeping interruptions.
Relieve the connection points of cables and lines from mechanical
stress.
Design strain relieves in such a way that they prevent any mechanical
damage to cables, wires or conductors caused by external influences
or their own weight.
To prevent damage to device connections, connectors and cables,
follow the instructions for proper installation in accordance with DIN
VDE 0100-520:2013-06, sections 522.6, 522.7 and 522.13.
Qualification requirements for personnel
Only allow qualified personnel to work on the device.
Qualified personnel have the following characteristics:
Qualified personnel are properly trained. Training as well as practical
knowledge and experience make up their qualifications. This is the
prerequisite for grounding and labeling circuits, devices, and systems
in accordance with current standards in safety technology.
Qualified personnel are aware of the dangers that exist in their work.
Qualified personnel are familiar with appropriate measures against
these hazards in order to reduce the risk for themselves and others.
Qualified personnel receive training on a regular basis.