Belden HIRSCHMANN MACH 100 Series User manual

MACH 100
Release 04 07/10
Technical Support
[email protected]
User Manual
Installation
Industrial ETHERNET Workgroup Switch
MACH 100 Family
MACH 102-8TP-F
MACH 102-24TP-F
MACH 102-8TP + M1-8TP-RJ45 + M1-8MM-SXC
MACH 102-8TP + M1-8SM-SXC + M1-8SFP

The naming of copyrighted trademarks in this manual, even when not specially indicated, should
not be taken to mean that these names may be considered as free in the sense of the trademark
and tradename protection law and hence that they may be freely used by anyone.
© 2010 Hirschmann Automation and Control GmbH
Manuals and software are protected by copyright. All rights reserved. The copying, reproduction,
translation, conversion into any electronic medium or machine scannable form is not permitted,
either in whole or in part. An exception is the preparation of a backup copy of the software for
your own use. For devices with embedded software, the end-user license agreement on the
enclosed CD applies.
The performance features described here are binding only if they have been expressly agreed
when the contract was made. This document was produced by Hirschmann Automation and
Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right
to change the contents of this document without prior notice. Hirschmann can give no guarantee
in respect of the correctness or accuracy of the information in this document.
Hirschmann can accept no responsibility for damages, resulting from the use of the network
components or the associated operating software. In addition, we refer to the conditions of use
specified in the license contract.
You can get the latest version of this manual on the Internet at the Hirschmann product site
(www.beldensolutions.com).
Printed in Germany
Hirschmann Automation and Control GmbH
Stuttgarter Str. 45-51
72654 Neckartenzlingen
Germany
Tel.: [phone]
039 710-001-04-07/10 – 16.7.10

MACH 100
Release 04 07/10 3
Contents
Safety instructions 4
About this manual 10
Legend 10
1 Device description 11
1.1 Description of the device variants 12
1.1.1 MACH 100 basic device 12
1.1.2 MACH 100 media modules 16
1.1.3 SFP modules 19
2 Assembly and start-up 21
2.1 Installing the device 21
2.1.1 Unpacking and checking 21
2.1.2 Installing the media modules 21
2.1.3 Installing the SFP modules 23
2.1.4 “FAULT” signal contact 24
2.1.5 Dimension drawings 25
2.1.6 Installing the device and grounding 25
2.1.7 Supply voltage 28
2.1.8 Startup procedure 31
2.1.9 Connecting the data lines 31
2.2 Display elements 34
2.3 Basic set-up 36
2.4 Disassembly 38
3 Technical data 40
A Further Support 47

4MACH 100
Release 04 07/10
Safety instructions
This documentation contains instructions which must be observed to ensure
your own personal safety and to avoid damage to devices and machinery.
Certified usage
The device may only be employed for the purposes described in the
catalog and technical description, and only in conjunction with external
devices and components recommended or
approved by the manufacturer. The product can only be operated cor-
rectly and safely if it is transported, stored, installed and assembled pro-
perly and correctly. Furthermore, it must be operated and serviced
carefully.
Supply voltage
The supply voltage is electrically isolated from the housing.
Use undamaged parts.
The device does not contain any service components. Internal fuses
are only triggered if there is a fault in the device. If the device is not
functioning correctly, or if it is damaged, switch off the voltage supply
and return the device to the plant for inspection.
Only switch on the device when the housing is closed.
Only use connection cables that are permitted for the specified
temperature range.
Relevant for North America:
Only use copper wire/conductors of class 1, 60/75°C or 75°C.
Warning!
Only connect a supply voltage that corresponds to the type plate
of your device.
Warning!
Use a fuse for the PoE supply voltage feed of the M1-8TP-
RJ45 PoE media module: 5 A slow blow.
Warning!
Disconnect the PoE voltage supply before removing the
M1-8TP-RJ45 PoE media module.
Warning!
Make sure that service personnel always have easy access to all
voltage supply connections of the basic device and the
M1-8TP-RJ45 PoE media module.

MACH 100
Release 04 07/10 5
Make sure that the disconnecting device is easily accessible so that
the MACH 100 device can be disconnected from the mains voltage.
If you disconnect the device from the mains voltage using
- the plug in the socket
- an on/off switch
it must be easily accessible.
Hinweis: For devices with redundant voltage supply (MACH 102-8TP-R,
MACH 102-8TP-FR, MACH 102-24TP-FR), both non-heating appliance
plugs must be pulled to disconnect the device from the main voltage. If the
M1-8TP-RJ45 PoE media module is used, the supply voltage also has to
be switched off or disconnected.
Shielding ground
The shielding ground of the connectable twisted pair lines is connected to
the protective conductor connection via the front panel.
Beware of possible short circuits when connecting a cable section with
conductive shielding braiding.
Housing
Only technicians authorized by the manufacturer are permitted to open
the housing.
The device is grounded via the voltage supply socket.
Make sure that the electrical installation meets local or nationally
applicable safety regulations.
The ventilation slots must not be covered so as to ensure free air
circulation.
The clearance to the ventilation slots of the housing must be at least
10 cm (3.94 in).
Warning!
Never insert sharp objects (small screwdrivers, wires, etc.) into
the inside of the product. There is the risk of an electric shock.
Close all empty slots with a covering panel.
The device must be installed in the horizontal or upright position, either
as a table unit in the switch cabinet (see fig. 16) or on the wall (see
fig. 17).
If you are operating the device in a 19" switch cabinet: install sliding/
mounting rails for holding the device (see fig. 15).
Environment
The device may only be operated at the specified maximum ambient
temperature (temperature of the surrounding air at a distance of up to 5
cm (1.97 in) to the device) and relative air humidity.

6MACH 100
Release 04 07/10
Install the device in a location where the climatic threshold values
specified in the technical data are adhered to.
Only to be used in an environment with a pollution degree specified in
the technical data.
Qualification requirements for personnel
Qualified personnel as understood in this manual and the warning signs,
are persons who are familiar with the setup, assembly, startup, and
operation of this product and are appropriately qualified for their job. This
includes, for example, those persons who have been:
trained or directed or authorized to switch on and off, to ground and to
label power circuits and devices or systems in accordance with current
safety engineering standards;
trained or directed in the care and use of appropriate safety equipment
in accordance with the current standards of safety engineering;
trained in providing first aid.
General safety instructions
Electricity is used to operate this equipment. Comply with every detail of
the safety requirements specified in the operating instructions regarding
the voltages to apply (see page 4).
Warning!
Only trained service personnel are authorized to plug the
M1-8TP-RJ45 PoE media module into the basic device or
remove from the basic device.
Non-observance of these safety instructions can therefore cause material
damage and/or serious injuries.
Only appropriately qualified personnel should work on this device or in
its vicinity. These personnel must be thoroughly familiar with all the
warnings and maintenance procedures in accordance with this
operating manual.
The proper and safe operation of this device depends on proper
handling during transport, proper storage and assembly, and
conscientious operation and maintenance procedures.
Never start operation with damaged components.
Only use the devices in accordance with this manual. In particular,
observe all warnings and safety-related information.
Any work that may be required on the electrical installation may only
be carried out by personnel trained for this purpose.

MACH 100
Release 04 07/10 7
Please note that products recommended as accessories may have
characteristics that do not fully correspond to those of the
corresponding product. This may limit their possible usage in the
overall system.
Note: LED or LASER components in compliance with IEC 60825-1
(2001):
CLASS 1 LASER PRODUCT
CLASS 1 LED PRODUCT
National and international safety regulations
Make sure that the electrical installation meets local or nationally
applicable safety regulations.
ESD Guidelines
The media modules are equipped with electrostatically sensitive
components. These can be destroyed, or their life cycles reduced, by the
effects of an electrical field or by a charge equalization if the card is
touched.
For this reason, the cards are packaged in a conductive ESD protective
bag on delivery. The packaging can be reused.
Make sure you adhere to the following protection measures for
electrostatically endangered assemblies:
Create electrical equipotential bonding between yourself and your
environment, e.g. using a wristband, which you clamp to the basic
device (knurled screw of an interface card). When the power supply
cable is connected, the basic device is grounded via the power supply
connection.
Only now do you take the card out of the conductive bag.
Outside the basic device, only store the cards in a conductive ESD
protective bag.
ESD protective field equipment is available for the safe handling of
electrostatically endangered assemblies.
You can find more information about electrostaticically endangered
assemblies in DIN/IEC 47 (Sec) 1330; February 1994 Edition and DIN EN
100 015.
CE marking
The devices comply with the regulations contained in the following
European directive(s):
2004/108/EG
Directive of the European Parliament and the council for standardizing
the regulations of member states with regard to electromagnetic
compatibility.

8MACH 100
Release 04 07/10
2006/95/EG
Directive of the European Parliament and the council for standardizing the
regulations of member states with regard to electrical equipment to be
used within specific voltage ranges.
In accordance with the above-named EU directive(s), the EU conformity
declaration will be at the disposal of the relevant authorities at the
following address:
Hirschmann Automation and Control GmbH
Stuttgarter Str. 45-51
72654 Neckartenzlingen
Tel.: [phone]
The product can be used in living areas (living area, place of business,
small business) and in industrial areas.
Interference immunity: EN 61000-6-2:2005
Emitted interference: EN 55022:2006 + A1:2007 Class A
Safety: EN 60950-1:2006
Warning!
This is a class A device. This device can cause interference in
living areas, and in this case the operator may be required to
take appropriate measures.
The assembly guidelines provided in these instructions must be
strictly adhered to in order to observe the EMC threshold values.
FCC note:
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions:
This device may not cause harmful interference, and
this device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to
radiocommunications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be required
to correct the interference at his own expense.

MACH 100
Release 04 07/10 9
Recycling note
After usage, this product must be disposed of properly as electronic
waste, in accordance with the current disposal regulations of your county,
state and country.

10 MACH 100
Release 04 07/10
About this manual
The following manuals are available as PDF files on the CD-ROM supplied:
Installation user manual
Basic Configuration user manual
Redundancy Configuration user manual
Web-based Interface reference guide
Command Line Interface user manual
The Network Management Software HiVision/Industrial HiVision provides
you with additional options for smooth configuration and monitoring:
Configuration of multiple devices simultaneously.
Graphical interface with network layouts.
Auto-topology discovery.
Event log.
Event handling.
Client / Server structure.
Browser interface
ActiveX control for SCADA integration
SNMP/OPC gateway
Legend
The symbols used in this manual have the following meanings:
Listing
Work step
Subheading