Belden Hirschmann MACH104-PoEP Series User manual

Installation MACH104-PoEP
Release 06 11/2013
Technical support
https://hirschmann-support.belden.eu.com
User Manual
Installation
Industrial Ethernet Workgroup Switch
MACH104-PoEP Full Gigabit Family
V.24USB
Aufkleber MAC-Adresse
P
FAULT
FAULT
Sb
RM
1
2
3
4
13
14
15
16
17
18
19
20
5
6
7
8
9
10
11
12
x y
MACH104
V.24USB
Aufkleber MAC-Adresse
P
FAULT
FAULT
Sb
RM
1
2
3
4
13
14
15
16
17
18
19
21 22
20
5
6
7
8
9
10
11
12
x y
MACH104
MACH104-16TX-PoEP+2X...
MACH104-16TX-PoEP+2X-R...
MACH104-16TX-PoEP+2X-E...
MACH104-16TX-PoEP...
MACH104-16TX-PoEP-R...
MACH104-16TX-PoEP-E...

The naming of copyrighted trademarks in this manual, even when not specially indicated, should
not be taken to mean that these names may be considered as free in the sense of the trademark
and tradename protection law and hence that they may be freely used by anyone.
© 2013 Hirschmann Automation and Control GmbH
Manuals and software are protected by copyright. All rights reserved. The copying, reproduction,
translation, conversion into any electronic medium or machine scannable form is not permitted,
either in whole or in part. An exception is the preparation of a backup copy of the software for
your own use. For devices with embedded software, the end-user license agreement on the
enclosed CD/DVD applies.
The performance features described here are binding only if they have been expressly agreed
when the contract was made. This document was produced by Hirschmann Automation and
Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right
to change the contents of this document without prior notice. Hirschmann can give no guarantee
in respect of the correctness or accuracy of the information in this document.
Hirschmann can accept no responsibility for damages, resulting from the use of the network
components or the associated operating software. In addition, we refer to the conditions of use
specified in the license contract.
You can get the latest version of this manual on the Internet at the Hirschmann product site
(www.hirschmann.com).
Printed in Germany
Hirschmann Automation and Control GmbH
Stuttgarter Str. 45-51
72654 Neckartenzlingen
Germany
Tel.: [phone]
Installation 039 782-001-06-1113 –
21.11.2013

Installation MACH104-PoEP
Release 06 11/2013 3
Contents
Safety instructions 5
About this manual 10
Legend 10
1 Description 11
1.1 General device description 11
1.2 Device name and product code 12
1.3 Device variants available 12
1.4 Device views 13
1.4.1 Front view 13
1.4.2 Rear view 14
1.5 Supply voltage 14
1.5.1 MACH104-16TX-PoEP...
MACH104-16TX-PoEP+2X... 15
1.5.2 MACH104-16TX-PoEP-R...
MACH104-16TX-PoEP+2X-R... 15
1.5.3 MACH104-16TX-PoEP-E...
MACH104-16TX-PoEP+2X-E... 15
1.6 Ethernet ports 15
1.6.1 10/100/1000 Mbit/s twisted pair port 15
1.6.2 100 Mbit/s F/O port 16
1.6.3 1000 Mbit/s F/O port 16
1.6.4 10-Gbit/s F/O port 17
1.6.5 PoE ports 17
1.6.6 Combo ports 18
1.6.7 SFP/XFP transceiver 18
1.7 Display elements 19
1.7.1 Device state 19
1.7.2 Port state 20
1.8 Management interfaces 21
1.8.1 V.24 interface (external management) 21
1.8.2 USB interface 22
1.9 Signal contact 22

4Installation MACH104-PoEP
Release 06 11/2013
2 Installation 23
2.1 Unpacking and checking the content of the package 23
2.2 Installing SFP/XFP transceivers (optional) 24
2.3 MACH104-16TX-PoEP-E...,
MACH104-16TX-PoEP+2X-E...:
Wiring and assembling the operating voltage 24
2.4 Wiring and assembling the signal contact 25
2.5 Installing the device and grounding 26
2.5.1 Selecting the assembly location 26
2.5.2 Mounting on a flat surface 27
2.5.3 Mounting in a switch cabinet 27
2.5.4 Mounting on the wall 28
2.5.5 Grounding the device 29
2.6 Operating the device 29
2.7 Connecting network cables 30
3 Basic set-up 31
3.1 Default settings 31
4 Maintenance and service 33
5 Deinstallation 34
5.1 Removing the device 34
5.2 Deinstalling the SFP/XFP transceivers 34
6 Technical data 35
A Further Support 44

Installation MACH104-PoEP
Release 06 11/2013 5
Safety instructions
Certified usage
Only use the device for application cases that are described in the
Hirschmann product information, including this manual. Only operate the
device according to the technical specifications.
Supply voltage
The supply voltage is electrically isolated from the housing.
Solely connect a supply voltage that corresponds to the type plate of
your device.
This applies to the following device variants only:
MACH104-16TX-PoEP-E...
MACH104-16TX-PoEP+2X-E...
Install an input fuse with a maximum rating of 10 A, characteristic B,
into the supply line to the voltage input.
Use conductors with a minimum cross-section of 1 mm2for the supply
line to the voltage input.
Exclusively connect SELV circuits with the voltage restrictions in
accordance with IEC/EN 60950-1 to the supply voltage connections.
Ensure that the connected supply voltage complies with the
requirements according to IEEE 802.3af or IEEE 802.3at.
Use undamaged parts.
The device does not contain any service components. Internal fuses
are only triggered if there is a fault in the device. If the device is not
functioning correctly, or if it is damaged, switch off the voltage supply
and return the device to the plant for inspection.
Only switch on the device when the housing is closed.
Only use connection cables that are permitted for the specified
temperature range.
Relevant for North America:
Only use copper wire/conductors of class 1, 60/75°C or 75°C.
Make sure that the disconnecting device is easily accessible so that
the MACH104-PoEP device can be disconnected from the mains
voltage.
If you disconnect the device from the mains voltage using
- the plug in the socket
- an on/off switch
it must be easily accessible.
This applies to the following device variants only:
MACH104-16TX-PoEP-R...
MACH104-16TX-PoEP+2X-R...
Pull both non-heating plugs to disconnect the device from mains
voltage.

6Installation MACH104-PoEP
Release 06 11/2013
Shielding ground
The shielding ground of the connectable twisted pair lines is connected to
the protective conductor connection via the front panel.
Beware of possible short circuits when connecting a cable section with
conductive shielding braiding.
Housing
Only technicians authorized by the manufacturer are permitted to open
the housing.
The device is grounded via the voltage supply socket.
Never insert sharp objects (small screwdrivers, wires, etc.) into the
inside of the device.
Verify that the electrical installation meets locally or nationally
applicable safety regulations.
Keep the ventilation slits free to ensure good air circulation.
Make sure there is at least 3.94 inches (10 cm) of space in front of the
ventilation slits of the housing.
The device must be installed in the horizontal or upright position, either
as a table unit in the switch cabinet (see figure 6) or on the wall (see
figure 7).
In order to fix the device to a concrete wall choose screws with a
thread major diameter of at least 5 mm.
Environment
Only operate the device at the specified ambient temperature
(temperature of the surrounding air at a distance of up to 5 cm from the
device) and at the specified relative humidity.
When you are selecting the installation location, make sure you
observe the climatic threshold values specified in the technical data.
Use the device in an environment with a maximum pollution degree
that complies with the specifications in the technical data.
Qualification requirements for personnel
Qualified personnel as understood in this manual and the warning signs,
are persons who are familiar with the setup, assembly, startup, and
operation of this product and are appropriately qualified for their job. This
includes, for example, those persons who have been:
trained or directed or authorized to switch on and off, to ground and to
label power circuits and devices or systems in accordance with current
safety engineering standards;
trained or directed in the care and use of appropriate safety equipment
in accordance with the current standards of safety engineering;
trained in providing first aid.

Installation MACH104-PoEP
Release 06 11/2013 7
General safety instructions
This device is operated by electricity. You must follow precisely the
prescribed safety requirements for the voltage connections in this
document.
See “Supply voltage” on page 5.
Non-observance of these safety instructions can cause material damage
and/or injuries.
Only appropriately qualified personnel should work on this device or in
its vicinity. The personnel must be thoroughly familiar with all the
warnings and maintenance procedures outlined in this operating
manual.
The proper and safe operation of this device depends on proper
handling during transportation, proper storage and assembly, and
conscientious operation and maintenance procedures.
Never start operation with damaged components.
Only use the devices in accordance with this manual. In particular,
observe all warnings and safety-related information.
Any work that may be required on the electrical installation may only
be carried out by personnel trained for this purpose.
Two or more devices configured with the same IP address can cause
unpredictable operation of your network.
Install and maintain a process that assigns a unique IP address to
every device in the network.
Please note that products recommended as accessories may have
characteristics that do not fully correspond to those of the
corresponding product. This may limit their possible usage in the
overall system.
Only connect the PoE connections to PoE-supplier devices whose
data connections are located in the interior of the building and are
specified as SELV circuits.
Note: LED or LASER components in compliance with IEC 60825-1
(2007):
CLASS 1 LASER PRODUCT
CLASS 1 LED PRODUCT
National and international safety regulations
Make sure that the electrical installation meets local or nationally
applicable safety regulations.
CE marking
The labeled devices comply with the regulations contained in the following
European directive(s):

8Installation MACH104-PoEP
Release 06 11/2013
In accordance with the above-named EU directive(s), the EU conformity
declaration will be at the disposal of the relevant authorities at the
following address:
Hirschmann Automation and Control GmbH
Stuttgarter Str. 45-51
72654 Neckartenzlingen
Germany
Tel.: [phone]
The product can be used in the industrial sector.
Interference immunity: EN 61000-6-2
Emitted interference: EN 55022
Reliability: EN 60950-1
Warning! This is a class A device. This device can cause interference in
living areas, and in this case the operator may be required to take
appropriate measures.
Note: The assembly guidelines provided in these instructions must be
strictly adhered to in order to observe the EMC threshold values.
FCC note
This device complies with part 15 of the FCC rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference; (2) this device must accept any interference received,
including interference that may cause undesired operation.
Device variant Directive
MACH104-16TX-PoEP...
MACH104-16TX-PoEP+2X...
MACH104-16TX-PoEP-R...
MACH104-16TX-PoEP+2X-R...
MACH104-16TX-PoEP-E...
MACH104-16TX-PoEP+2X-E...
2011/65/EU (RoHS)
Directive of the European Parliament and of the Council on
the restriction of the use of certain hazardous substances in
electrical and electronic equipment.
2004/108/EC (EMC)
Directive of the European Parliament and the council for
standardizing the regulations of member states with regard to
electromagnetic compatibility.
MACH104-16TX-PoEP...
MACH104-16TX-PoEP+2X...
MACH104-16TX-PoEP-R...
MACH104-16TX-PoEP+2X-R...
2006/95/EC
Directive of the European Parliament and the council for
standardizing the regulations of member states with regard to
electrical equipment to be used within specific voltage
ranges.

Installation MACH104-PoEP
Release 06 11/2013 9
Appropriate testing has established that this device fulfills the
requirements of a class A digital device in line with part 15 of the FCC
regulations.
These requirements are designed to provide sufficient protection against
interference when the device is being used in a business environment.
The device creates and uses high frequencies and can also radiate high
frequencies, and if it is not installed and used in accordance with this
operating manual, it can cause radio transmission interference. The use
of this device in a living area can also cause interference, and in this case
the user is obliged to cover the costs of removing the interference.
Recycling note
After usage, this device must be disposed of properly as electronic waste,
in accordance with the current disposal regulations of your county, state,
and country.

10 Installation MACH104-PoEP
Release 06 11/2013
About this manual
The “Installation” user manual contains a device description, safety
instructions, a description of the display, and the other information that you
need to install the device.
The following manuals are available as PDF files on the CD/DVD supplied:
Installation user manual
Basic Configuration user manual
Redundancy Configuration user manual
Reference manual for the graphical user interface
Command Line Interface user manual
The Industrial HiVision Network Management Software provides you with
additional options for smooth configuration and monitoring:
ActiveX control for SCADA integration
Auto-topology discovery
Browser interface
Client/server structure
Event handling
Event log
Simultaneous configuration of multiple devices
Graphical user interface with network layout
SNMP/OPC gateway.
Legend
The symbols used in this manual have the following meanings:
Listing
Work step
Subheading