Belmont X-Calibur V BEL-50 User manual

INSTALLATION
INSTRUCTIONS
DENTAL CHAIR
BEL-50
1E0570DE
IMPORTANT
This manual provides installation instructions for the BEL-50 Chair.
The instructions contained in this booklet should be throughly read and
understood before installation of the chair.
After the installation has been completed, keep this manual in a safe place.
R

Table of Contents
1. Overview and Major Components --------------------------------------- 1
2. Dimensions and Specications ----------------------------------------- 2
3. Introduction -------------------------------------------------------------- 3
4. Installation --------------------------------------------------------------- 4
5. Adjustment ----------------------------------------------------------------- 8
6. Electric Diagram ----------------------------------------------------------10

Intended Use of the P r oduct
This product is intended for the exclusive use for diagnoses, treatments and relative procedures of
dentistry, and must be operated or handled by the qualified dentists or by dental staffs under the
supervision of the dentist.Such dentists or dental staffs should instruct and/or assist the patients to
approach to and leave from the product. Patients should not be allowed to operate or handle the
product unless he/she is so instructed.
Environmental Requirements
Operating Ambient Temperature 32°F ~ 104°F (0°C ~ 40°C)
Humidity 10% ~ 95%
Atmospherical Pressure 10psi ~ 15.4psi (700hpa ~ 1060hpa)
Storage Ambient Temperature -4°F ~ 158°F (-20°C ~ 70°C)
Humidity 10% ~ 95%
Atmospherical Pressure 10psi ~ 15.4psi (700hpa ~ 1060hpa)
Classification
a. Protection against electric shock : Class I Equipment, Type B Applied Parts (Headrest,
Backrest and Seat cushions)
b. Protection against water ingress : Chair (IPX0), Foot control (IPX1)
c. Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with
oxygen or nitrous oxide.
d. Mode of operation : Non-continuous operation
Maximum activation time: 3 minutes, Duty cycle 1:5
CAUTION
This product may be affected by sources that generate excessive electromagnetic waves.
Do not install this equipment close to such devices such as elevators or communication equipment,
including cellular telephones.
Do not position this equipment so that it is difficult to access the main power supply outlet that the
power plug of this chair is connected to.
Symbol
Applied part complying with the specified requirements of IEC60601-1:2005 to provide
protection against electrical shock, particularly regarding allowable patient leakage current
and patient auxiliary current.
Caution*The base color is yellow.
Manufacturer
Date of Manufacture

1. Overview and Major Components
17
15
12
11
10
20
14
13
18
19
6
5
4
7
8
9
21
22 3
2
1
16
Figure 2
BACKREST CONTROL
Figure 3
FOOT CONTROL
Backrest
Raise
Auto
Return
Backrest
Recline
Seat Raise
Seat Lower
Pre-set 2
Pre-set 1
Pre-set 3
Program (Pre-set 1)
Seat Raise
Seat Lower
Backrest Raise
Backrest Recline
Auto Return
A
Figure 1
1. Headrest Assembly
2. Backrest Cushion
3. Armrest
4. Main Link Cover
5. Sub Link Cover
6. Base Cover
7. Power Supply Cable
8. Pump Cover
9. Seat Cushion
10.Backrest Cover
11.Seat Back Support
12.Dome Casting Cover
13.Tilt Cover
14.Rotating Flange Cover
15.Rotation Lock Lever
16.Foot Control Ass'y
17. Sub Link Cover(Lower)
18. Main Power Switch
19. Fuse Holder
20. Backrest Control Panels
21. Side Frame (Left)
22. Side Frame (Right)
- 1 -

2-1. Dimensions (Inches)
2. Dimensions and Specications
* Sealed hydraulic system powered by 3.5 A motor pump
* Base plate: 1/2" steel
* Bearings at link points - low friction in steel jacket.
* Steel backrest support
* Electrical requirements : AC120V/60Hz/3.7A
* Fuse for power supply : 10A/125V (Current rating : 750A at 250VAC) Fast-blow
* Fuse for relays : 1.25A/125V (Current rating : 750A at 250VAC) Fast-blow
* Hospital grade plug
* Base component housing formed from solid color acrylate styrene acrylonitrile (ASA ,V0)
* All exposed ferrous parts covered with corrosion-resistant paint or plating
* Weight: 320 lbs. (145 kg)
2-2. Specications
23-1/4
15-7/8
23-7/8
23-5/8
18-1/2
8
5-1/4
34-3/4 22-1/4
30-5/8
54-1/2
37-11/16
5-1/4
5-1/4 20-1/4
74-1/4
13-3/8
28-3/8
34-3/424-1/2 15
22-3/4
74-1/4
34-3/417-9/16 22 20
˚
70 ˚
20 ˚
6 ˚
10 ˚
6 ˚
23-1/4
15-7/8
23-7/8
23-5/8
18-1/2
8
5-1/4
34-3/4 22-1/4
30-5/8
54-1/2
37-11/16
5-1/4
5-1/4 20-1/4
74-1/4
13-3/8
28-3/8
34-3/424-1/2 15
22-3/4
74-1/4
34-3/417-9/16 22 20
˚
70 ˚
20 ˚
6 ˚
10 ˚
6 ˚
- 2 -

3-1. Precautions for Installation
• Keep the equipment away from water.
• Keep in a circumstances safe from influence by temparature, humidity, wind, sun light, air containing
salts and minerals.
• Care about stability such as inclination, vibration and impact, including handling and transportation.
• Do not keep the equipment in a place where chemicals are or where gas is emitted.
• The floor construction required to safely support the chair and delivery system is 105 lbs./ft2
(500kg/m2 ) at minimum.
• During lifting and unpacking of the chair, make sure to hold only the designated parts.
• Do not drop or hit the chair.
• After the chair is unloaded from the palette and placed at the desired location, please make sure to
remove the shipping bolt with the red tag. Damage to chair may occur if shipping bolt is
not removed prior to chair operation.
• Do not connect to power supply other than AC120V 60Hz.
• Ground chair properly prior to turning power on.
• Chair base must be anchored to the floor for maximum stability.
• Refer to the installation manual of the chair and dental unit (if it is to be used) prior to, and
during installation.
• When the installation process has been completed, verify that all the mechanical and electrical
functions are working properly and that there is no evidence of oil leakage.
• Protective footwear and thick gloves are highly recommended at unpacking.
• Do not modify this equipment.
• In the case separation from any electrical poles is necessary, pull of the power plug from the power
supply outlet.
3-2. Required Tools
The following tools are necessary for installation of the chair.
Phillips screw driver #2
Allen key wrenches, metric size
3. Introduction
- 3 -

Side Frame
Main Link Axis
Packing Screw
Toe board bar
4. Installation
3) Lift chair base from pallet into the
installation location.
Be sure to lift chair under the side frame
and main link axis as shown in Figure 2.
1) Place chair carton close to installation
location.
Remove all the staples fixing the carton to
pallet, or cut the carton just above the
stapled line, and remove the carton.
(See Figure 1.)
Figure 1
Figure 3
4) Before attaching chair to the electrical
power source, remove red shipping bolt
from the seat structure using a 13mm
socket. (See Figure3.)
5) Remove the following items from chair
packaging:
• Backrest Frame Assembly
• Plastic Base Cover
• Small Carton Box Containing Armrests,
Headrest Mechanism and Bag of Hardware.
Figure 2
2) Using a 10mm socket, loosen and remove
two packing screws holding the chair base
into pallet. (See Figure 2.)
Staples
Red Shipping Bolt
CAUTION
Do not lift chair by toeboard bar
Do not connect in the power supply line
before removeing the red tagged
shipping bolt.
CAUTION
4-1. Unpacking the Chair Base
- 4 -

5) Remove 2(5mm x 8) phillips head
screws that secure the plastic
backrest cover to
the metal backrest frame (Figure 6b).
Using a 10mm hex key wrench,
attach backrest frame to seat back
support using 4(10mm x25) socket
head cap screws.(See Figure 5 a.)
6) Connect backrest quick connect plug
to chair connector plug (tie up the
excess wire harness with a cable tie).
(See Figure 5 a.) Figure 5 a
4) Remove the side cover and attach each
armrest to side frame as shown in
Figure 4 (it may be necessary to lightly
lubricate armrest shaft with silicone lube).
Figure 4
1) Plug chair into 120VAC outlet.
2) Turn on the main power switch located on the left side of the pump cover. A green lamp
will illuminate.
3) Raise the seat by foot switch.
To avoid the risk of electrick shock, this equipment must only be connected to a supply mains with
protective earth. Grounding reliability can only archieved when the equipment is connected to an
equivalent receptacle marked HOSPITAL ONLY or HOSPITAL GRADE.
CAUTION
Operate the Main Power Switch by hand only. Turn off the main switch after daily operation.
CAUTION
Do not touch a switch on the foot control during the main power switch is being turned on.
NOTE
4-2. Installation
Armrest
Side Frame
Side Cover
Screw
(5mm x 10)
Armrest Spring
Flat Washer(O.D.22 x I.D.6.5)
Armrest Screw(6mm x 80)
Backrest Frame
Socket Head Cap Screw
Seat Back Support
Chair Connector Plug
Backrest Quick Connect Plug
(10mm x 25)
- 5 -

Backrest Cover
Backrest Cushion
Alignment Bolts
Eyelet Holes
Threaded Brackets
Phillips head screws
Backrest Frame
(5mm x 8)
Round Head Screws
(1/4 - 20 x 3/4)
7) Re-attach plastic backrest cover to
backrest frame, as follows;
a) Insert backrest cover alignment
bolts into eyelet holes in backrest
frame, as shown in figure 6a.
b) Connect wire harness from back
rest membrane switches to
connector PC Board on the Back
rest Frame.
c) Press backrest cover against
backrest frame and push
backrest cover upward.
Make sure the 2 small threaded
brackets on the lower edge of the
backrest frame are inside of the
backrest cover.
d) Secure backrest cover to
backrest frame by using 2
(5mm x 8) phillips head screws,
as shown in figure 6b.
Figure 6a
Alignment Bolts
Backrest Cover
Backrest
Frame
Eyelet Holes
Figure 6b
Headrest Cushion
Headrest Mechanism
Phillips Flat Head Screw
(10 - 24 x 3/4 )
Headrest Bar
8) Attach headrest cushion to headrest
mechanism by using 4(10-24 x 3/4)
phillips flat head screws and slide
headrest bar into opening in top of
backrest. (See Figure 6c)
Figure 6c
- 6 -