Belmont PHOT-XIIS 505 Specifications

OPERATOR'S
INSTRUCTIONS
This X-ray equipment may be dangerous to patient and operator
unless safe exposure factors, operating instructions and maintenance
schedules are observed.
WARNING
R
·Wall Mount Type ....................WK
·Floor Mount Type ..................FK1/FK2
·Mobile Type............................FM
·Room Mount Type ..................RK
·Ceiling Mount Type................CK
505
DENTAL X-RAY

INDEX
Page
[ 1 ] INTRODUCTION --------------------------------------------------------------- 1
[ 2 ] MAJOR COMPONENTS ------------------------------------------------------ 2
[ 3 ] FUNCTION OF CONTROLS ------------------------------------------------- 6
[ 4 ] OPERATING PROCEDURES ------------------------------------------------- 9
[ 5 ] ESTIMATED AIR KERMA ---------------------------------------------------- 9
[ 6 ] OPTIONAL HAND EXPOSURE SWITCH --------------------------------- 9
[ 7 ] DIGITAL IMAGING SYSTEM ---------------------------------------------- 10
[ 8 ] DISINFECTION AND CLEANING ----------------------------------------- 10
[ 9 ] ERROR CODES ---------------------------------------------------------------- 11
[ 10 ] MAINTENANCE ------------------------------------------------------------- 12
[ 11 ] DISPOSAL -------------------------------------------------------------------- 12
[ 12 ] TECHNICAL DATA ------------------------------------------------------- 14
[ 13 ] ELECTROMAGNETIC COMPATIBILITY (EMC) --------------------- 16
[ 14 ] LABEL LOCATION ------------------------------------------------------- 19

[ 1 ] INTRODUCTION
 *(1(5$/
This manual provides information for the operation and maintenance prodedures and technical
specifications for PHOT-X IIs 505 dental x-ray. The instructions contained in this book should
be thoroughy read and understood before operetion.
PHOT-X IIs 505 has no user serviceable items. Repair should be performed by qualified
dealer service personnel.
2 ,17(1'('86(2)7+(352'8&7
3+27; ,,VLVDnH[WUDRUDOVRXUFHGHQWDOUDGLRJUDSKLF[UD\XQLW7KLVXQLWis an active
device intended to emit diagnostic purpose ionizing radiation, and must be operated or handled
by qualified personel only. Such qualified personnel should instruct and/or assist with the
patients approach to and from the product. Patients should not be allowed to operate or handle
the product. It is always recomended that both operator and patient use the proper protective
means for radiographing.
 3$576,'(17,),&$7,212);5$<6<67(03+27; ,,V
D 7XEHKRXVLQJDVVHPEO\ +
E ;UD\FRQWUROV &0PDLQFRQWUROOHU&6VXEFRQWUROOHU
F &RQHV 5UHJXODU/ORQJ
d. Collimator : 505-REC (rectangular)
e %DODQFHDUP : $
 &203/,$1&(:,7+67$1'$5'
3+27;,,V[UD\XQLWFRPSOLHVZLWKWKHIROORZLQJVWDQGDUGs
IEC60601-1:2005, IEC60601-1-3:2008, IEC60601-2-65:2012
5. CLASSIFICATION
$FFRUGLQJWR,(&3+27;,,VLVFODVVLILHGDVIROORZV
D 3URWHFWLRQDJDLQVWHOHFWULFVKRFN &ODVV,(TXLSPHQW
b. Type of applied parts : Type B (RK type only)
c 3URWHFWLRQDJDLQVWLQJUHVVRIZDWHU 2UGLQDU\
d 0RGHRIRSHUDWLRQ 1RQFRQWLQXRXV 'XW\&\FOH ,
Max. ON time : 2.0 sec, Min. OFF time : 12 sec.)
e (TXLSPHQWQRWVXLWDEOHIRUXVHLQWKHSUHVHQFHRIDIODPPDEOHDQHVWKHWLFPL[WXUHZLWK
DLURUZLWKR[\JHQRUQLWURXVR[LGH
6. SAFETY
This X-ray Unit may be dangerous to patient and operator unless safe exposure factors,
operating instructons and maintenance schedules are observed.
Only qualified and authorized personnel may operate this equipment observing all laws
and regulations concerning protection. The operator must :
· heve means for audio and visual communication with the patient.
· have full view of kV, mA, timer selections and exposure warning light.
· be at least 2 m away from the x-ray head and patient and out of the path of the x-ray beam
or be positioned behind a protective device.
· fully use all radiation protection devices, accessories and procedures available to protect
the patient and operator from x-ray radiation.
-1-

-2-
7. SYMBOL
In this book, on the labels or on the control panel of PHOT-X IIs 505, following symbols
are used. Confirm the meanings of each symbol by the table below.
[ 2 ] MAJOR COMPONENTS
1. FLOOR MOUNT TYPE (FK1/FK2)
1Main Power Switch
2X-Ray Head
3Cone
4Yoke
5Arm Collar
6Balance Arm
7Horizontal Arm (300mm)
8Pole Bush
9Back Supporter
10 Pole
11 Base Cover
12 Mounting Plate
13 Main Controller
14 Sub Controller
15 Hand Exposure Switch
Fig.2-1 Major Components for FK1/FK2
C
T1 T5
T2 T3 T4
F
D
P
kV
60 7
0
mA
ab
4
7
INC
INC
CUS & PM
CUS & PM
MLR OCC
MLR BW
8
8
6
9
13
14
15
6
1
1
10
11
12
7
14
15
7
9
10
11
12
2
3
4
2
3
4
5
5
13
C
T1 T5
T2 T3 T4
F
D
P
kV
60 7
0
mA
ab
4
7
INC
INC
CUS & PM
CUS
&
PM
MLR OCC
MLR BW
Type FK1 Type FK2
Protection
against electric
shock : Type B

ON (POWER)

OFF (POWER)



Protection
Grounding


Exposure
Switch

X-ray
Emission



Ready


Upper Incisor


Upper Cuspid
& Pre Molar

Upper Molar

Occlusal



Lower Incisor



Lower Cuspid
& Pre Molar
Lower
Molar
& Bite Wing

Bite Wing

Digital
Imaging

Patient
Child

Patient
Normal

Patient
Obese

Regular
Cone

Long
Cone

Non-ionizing
Radiation

Date
of
Manufacture
Consult written
Instructions in
Manuals

-2-

-3-
2. MOBILE TYPE (FM)
3. ROOM MOUNT TYPE (RK)
C
T1 T5
T2 T3 T4
FD
P
kV
60 70
mA
ab
4 7
INC
INC
CUS & PM
CUS & PM
MLR OCC
MLR BW
8
7
6
2
3
4
5
9
10
11
12
13
11
10
14
15
16
1
Fig.2-2 Major Components for FM
Fig.2-3 Major Components for RK
1Main Power Switch
2X-Ray Head
3Cone
4Yoke
5Arm Collar
6Balance Arm
7Pole Bush
8Pole
9Pole Base
10 Leg Bar (long)
11 Leg Bar (Short)
12 Lock Caster
13 Standard Caster
14 Main Controller
15 Sub Controller
16 Hand Exposure Switch
1Main Power Switch
2X-Ray Head
3Cone
4Yoke
5Arm Collar
6Swing Arm 1
7Swing Arm 2
8Sliding Post
9Column Cover
10 Colum
11 Backrest Cushion (applied part)
12 Seat (applied part)
13 Gas Cylinder
14 Base Plate
15 Main Controller
16 Sub Controller
Hand Exposure Switch(option)
17
1
2
4
5
6
7
8
9
10
12
13
14
15
3
11
16 17
C
T1 T5
T2 T3 T4
FD
P
kV
60 70
mA
ab4 7
INC
INC CUS & PM
CUS & PM MLR OCC
MLR BW
WARNING
Keep casters in the lock position, unless mov-
ing the equipment. To avoide injury, do not
push or lean on the equipment.
CAUTION
Do not move entire x-ray unit with arm
extended.

-4-
4. WALL MOUNT TYPE (WK)
910
C
T1 T5
T2 T3 T4
FD
P
kV
60 70
mA
ab
4
7
INC
INC
CUS & PM
CUS & PM
MLR OCC
MLR BW
Major Components for WK
1
Main Power Switch
2
X-Ray Head
3
Cone
4
Yoke
5
Arm Collar
6
Balance Arm
7
Horizontal Arm
8
Main Controller
9
Sub Controller
10
Hand Exposure Switch (Option)
C
T1 T5
T2 T3 T4
FD
P
kV
60 70
mA
ab
4 7
INC
INC
CUS & PM
CUS & PM
MLR OCC
MLR BW
10
11
14
12
15
16 17
13
1
2
3
4
5
6
7
8
18
9
18
1
Main Power Switch
2
X-Ray Head
3
Cone
4
Yoke
5
Arm Collar
6
Balance Arm
7
Swing Arm
8
Swing Post
9
Cover Ring
10
Light Arm (Option)
11
Ceiling Pole
12
Main Controller Bracket
13
Main Controller
14
Ceiling Cover
15
Ceiling Mounting Plate
16
Sub Controller
17 Hand Exposure Switch (Option)
18
Support Ring
5. CEILING MOUNT TYPE (CK)
Fig.2-5
Fig.2-4
Major Components for CK
2
4
5
6
7
8
3
1

P
3
4
5
6
7
2
8
9
10 11 12 13 14
15
17
18
16
1 Sub controller front panel
2 Ready Light
10 Cone Type Selection Switch
11 Film Speed Selection Switch
3 Exposure Time Adjusting Switch (Down) 12 Digital Imaging Switch
4 Exposure Time Adjusting Switch (Up) 13 kV Selection Switch
5 Tooth Selection Switch (T1)
6 Tooth Selection Switch (T2)
7 Tooth Selection Switch (T3)
8 Tooth Selection Switch (T4)
9 Tooth Selection Switch (T5)
14 mA Selection Switch
15 Patient Size Selection Switch
16 Exposure Time Display Window
17 Exposure Warning Light
18 Exposure Switch
-5-
6. SUB CONTROLLER
Fig.2-6 Sub Controller Switches
1

6
>@)81&7,212)&21752/6
 0DLQ3RZHU6ZLWFK
3XVKLQJWKHXSSHUVLGHRIWKLVVZLWFKWRWKH21SRVLWLRQHQHUJL]HVWKH[UD\XQLW5HDG\OLJKW
DQGSUHVHOHFWOLJKWVIRUFRQHW\SHILOPRUGLJLWDON9P$DQGSDWLHQWVL]HLOOXPLQDWH
,WLVUHFRPPHQGHGWRNHHSWKLVVZLWFK2))ZKHQWKHXQLWLVQRWLQXVHLQRUGHUWRSUHYHQWDQ
DFFLGHQWDOH[SRVXUH
,03257$177RSUHYHQWWKHULVNRIDQDFFLGHQWDOH[SRVXUHSXVKWKHORZHUVLGH
RIWKLVVZLWFKWRWKH2))SRVLWLRQZKHQWKHXQLWLVQRWLQXVH
 5HDG\/LJKW
7KLVOLJKWLOOXPLQDWHVZKHQWKHOLQHYROWDJHLVZLWKLQRSHUDEOHUDQJH. Rated line voltage
±10%) WKHQWKLVOLJKWLVQRWRQH[SRVXUHFDQQRWEHPDGH
 ([SRVXUH7LPH$GMXVWLQJ6ZLWFKHV
%\PRPHQWDULO\SXVKLQJWKH RU VZLWFKWKHH[SRVXUHWLPHGLVSOD\HGLQFUHDVHVRU
GHFUHDVHVE\RQHLQFUHPHQW%\NHHSLQJWKHVZLWFKGHSUHVVHGPRUHVHFWKHH[SRVXUHWLPH
GLVSOD\HGLQFUHDVHVRUGHFUHDVHVFRQWLQXRXVO\XQWLOWKHVZLWFKLVUHOHDVHG
Phot-X IIs KDVWKHIROORZLQJH[SRVXUHWLPHVHWWLQJV


VHF
 a 7RRWK6HOHFWLRQ6ZLWFKHV7a7
3XVKLQJRQHRIWKHVHVZLWFKHVVHWVWKHH[SRVXUHWLPHDXWRPDWLFDOO\IRUWKHIROORZLQJ a 
 7,QFLVRURI0DQGLEOH
 7,QFLVRURI0D[LOOD&XVSLG3UHPRODURI0DQGLEOH
 7&XVSLG3UHPRODURI0D[LOOD0RODUVRI0DQGLEOH%LWHZLQJ
 70RODURI0D[LOOD%LWHZLQJ0RODUV
 72FFOXVDO
,IWKH7VZLWFK LVGHSUHVVHGPRUHWKDQVHFXQLWJRHVLQWR/RFN0RGH,QORFNPRGH
WKHRQO\IXQFWLRQDOVZLWFKLVWKHSRZHUVZLWFK7RH[LWIURPWKHORFNPRGHGHSUHVVWKH
7
VZLWFhPRUHWKDQVHFDJDLQ
 &RQH7\SH6HOHFWLRQ6ZLWFK
'HSUHVVLQJWKLVVZLWFKIRUPRUHWKDQVHFVHOHFWVWKHFRQHW\SH203mm sWDQGDUGFRQHRU
305mm oSWLRQDOORQJFRQH
 )LOP6SHHG6HOHFWLRQ6ZLWFK
D 3+27; ,,V505 KDVILOPVSHHGVHWWLQJV)a)
7ZRVSHHGVHWWLQJVDUHSUHVHWDWWKHIDFWRU\DEDQGFDQEHVHOHFWHGZLWKVZLWFK
D )LOPVSHHG1R)HTXLYDOHQWWR,62VSHHGJURXS'RU.RGDN8OWUD6SHHGILOP
E )LOPVSHHG1R)HTXLYDOHQWWR,62VpHHGJURXS)(RU.RGDN,Q6LJKWILOP
Including these two speeds, PHOT-X IIs 505 x-ray can provide 16 different film speeds
(F.00 ~ F.15) and any two of them can be programmed for easy selection. If doctor uses a
different film speed, or prefers darker (or lighter) radiographs, the new speed can be
programmed as follows. Higher speed settings make films darker. If film speed is
increased by 1, exposure time becomes 25 % longer.
1. Keep the kV selection switch and mA selection switch depressed simultaneously for
more than 3 seconds. Release the switches if the ready light starts to flash.

2. Push F switch momentarily until the "a" light above the F switch illuminates. The exposure
time display window shows the present film speed for "a" setting. (The factory default setting,
F.09 should be displayed.) By depressing or switch, increase or decrease film speed
number until desired number for "a" setting is displayed.
3. To change the "b" setting from the factory default, F.05, push F switch momentarily until the
"b" light illuminates. By depressing or switch, increase or decrease film speed until the
desired number for "b" setting is displayed.
4. Press T1 switch to store these settings, then turn the main power switch off.
b. Pushing Film Speed Selection Switch 11 momentarily displays the selected film speed setting
in the Exposure Time Display Window 16
Depressing this switch for more then 2 sec. changes the film type being selected.
c. If the Digital Imaging Switch 12 is depressed, both of the film speed indicating lights (a & b)
are turned off.
 'LJLWDO,PDJLQJ6ZLWFK
,IDGLJLWDOLPDJLQJV\VWHPLVXVHGVKRUWHUH[SRVXUHWLPHLVRIWHQUHTXLUHG3+27;,,VKDV
VSHHGVIRUGLJLWDOLPDJLQJGaG3XVKLQJWKLVVZLWFKPRPHQWDULO\GLVSOD\VWKHVSHHG
EHLQJVHOHFWHGLQWKH([SRVXUH7LPH'LVSOD\:LQGRZ:LWKWKHIDFWRU\VSHHGVHWWLQJG0
WKHH[SRVXUHWLPHEHFRPHVKDOIRI)10VHWWLQJ
As the sensitivity is different according to each manufacturer of digital imaging sensors, this
setting should be adjusted. To get a darker image, increase the speed setting and to get a lighter
image, decrease the speed setting. If the speed setting is increased by 1, exposure time becomes
12 % longer.
1. Keep kV selection switch and mA selection switch depressed simultaneously for more than
3 seconds. Release the switches if the ready light starts to flash.
2. Push D switch momentarily until the light above the D switch illuminates and the exposure
time display window shows the present speed setting. (The factory default setting d.10
should be displayed.)
3. By depressing or switch, increase or decrease speed until the desired number is
displayed.
4. Press T1 switch to store these settings, then turn the main power switch off.
13 kV Selection Switch
Momentarily depressing this switch will change the tube potential to 60 or 70 kV. If either the Film
Speed Switch 11 or Digital Imaging Switch 12 is depressed, 60kV is automatically selected.
14 mA Selection Switch
Momentarily depressing this switch will change the tube current setting (3 or 6 mA). If the Digital
Imaging Switch 12 is depressed, 3 mA is automatically selected and if the Film Speed Switch 11
is depressed, 6 mA is automatically selected.
7