Belnick BO-BS7002-1-GY-GG User manual

Thankyouforyourpurchase!
Push Back Recliner
ASSEMBLY INSTRUCTIONS
Before You Begin:
Please identify all component parts and hardware pieces required before you begin. Carefully remove all of
the components from the packaging and set aside for assembly. Assemble on a soft surface to prevent
scratching during assembly.
Caution:
Tighten all components securely before use. Failure to do so may result in personal injury.
DO NOT use any sharp objects to open plastic wrapped components as damage to product or components
may result.
Warning:
CHOKING HAZARD - Small Parts. Adult Assembly Required.
DO NOT ALLOW CHILDREN TO CLIMB ON FURNITURE
Serious or fatal injuries can occur from furniture tipping over. You must install Tipping Restraint Hardware
(where included) to help prevent the unit from tipping and causing accidental injury, instability, death or
damage. The tipping restraint is intended only as a safety measure, it is not a substitute for proper adult
supervision.
To help prevent furniture from tipping over it must be permanently attached to the wall. Anti-Tip Safety Wall
Straps suitable for the unit weight and wall materials (if not included) should be purchased and installed.
Online Assembly Instructions: http://ftp.flashfurniture.com/AssemblyInstructions/BO-BS7002-1-GY-GG.pdf
Customer Service Email: [email protected] | Phone: [phone]
BO-BS7002-1-GY-GG / BO-BS7002-1-CREAM-GG

Have a Question/Concern?
Quality products and first-class customer service are the cornerstone of long-lasting
consumer relationships. We strive toward excellence in all we do and want you to be
completely satisfied with your purchase.
Please contact our exceptional Customer Experience Agents at the email
address or phone number shown below to assist you with any product
questions or issues before requesting a return.
We look forward to serving you in a friendly, efficient manner to resolve any issues
you may have.
Customer Service Email: [e-mail] Customer
Service Phone: [phone]
Our Warranty Statement
This warranty covers manufacturing defects associated with your new product. The product is
warranted from the original purchase date and to the original purchaser for normal usage,
according to the
below-referenced specifications and limitations.
Non-moving metal parts are warranted for 5 years.
Component parts including pneumatic cylinder, control mechanism, base and casters are warranted
for 2 years.
All other items are warranted for 1 year.
Normal usage means use in compliance with the restrictions and weight limits specified for the
product. In the absence of product-specific restrictions and weight limits, normal usage means
use for no more than forty hours per week by persons weighing 250 lbs. or less. Coverage
terminates if the product is sold or otherwise transferred. Repairs made by parties other than
Belnick also void this warranty.
This warranty will not cover: (1) labor, freight, or damage from misuse, abuse, negligence,
alteration, assembly, installation, attachments, accident, vandalism, acts of nature or any other
event beyond the control of Belnick; (2) tearing, scratching, scuffing, or blemishing of leather or
fabric; (3) cosmetic damage that may result from normal usage; (4) damage attributable to use
by persons exceeding specified weight limits or commercial use exceeding forty hours per week;
or (5) rust or other damage caused by exposure to moisture. The user assumes all risk of injury
resulting from use of this product. Liability for incidental or consequential damage is excluded.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so
the above limitation or exclusion may not apply to you.

PARTS
A
Back
1pcs
C
Seat
1pcs
B1
Left Wing Back
1pcs
D
Front Leg
2pcs
B2
Right Wing Back
1pcs
E
Rear leg
2pcs
STEP 1
Left Back Wing
Step 1: With the inner seat back
facing front, attach Left Wing
Back (Part B1) and Right Wing
Back (Part B2) to Back (Part A)
by sliding metal inserts onto
corresponding inserts on the sides
of the back.
Step 2: Tighten Front Legs (Part
D) and Rear Legs (Part E) to seat
bottom leg assembly holes.
Return set to the upright position.
Note:Frontlegsaretapered, rear
legs arecurved.
Step 3: Attach Back to the Seat
by inserting back bottom metal
inserts onto corresponding seat
inserts on seat back.
RightBackWing
Back
Back
Seat
STEP 3
STEP 2
Rear leg
Seat
Frontleg