Sprout BMS User manual

1
Simple. Modern. American Made.
Adult assembly only
2 Adults required for assembly
Assemble completely before use
Full Back
Birch
Montessori
Shelf

DOCUMENT: AI-B.2-NoBack WWW.SPROUT-KIDS.COM COPYRIGHT QUARK ENTERPRISES 2018 PAGE 3 OF 12
BEFORE YOU START
Parts
RECCOMENDED: A rubber
mallet can help push
pieces together.
A hammer can also be
used with a scrap piece of
wood or a cutting board
placed over the surface
being hammered for
protection.
*additional parts may be included
depending on unit ordered.
Assembly instructions for various
base options are included with this
pamphlet.
Has Slots
Toe (1)
a
Bottom Shelf* (1)
Top Shelf (1)
Left Side* (1) Right Side* (1)
Adjustable Shelf (1)
Pins (4)
Full Back (1)
or
Split Full Back (2)
A
B
C
DE
F
G
H
*When inserting tabs into slots make
sure the side with the wider lip on
the tab faces the same direction as
the notch in the slot.
NOTCH
WIDE LIP
SLOT TAB
TAB
SLOT
TAB LOCKED INTO SLOT

QUARK ENTERPRISES, LLC PO BOX 1123, PROVO, UT 84601 MODEL NO. BMSPAGE 4 OF 12
Frustrated?
Need Help?
STOP
ASSEMBLY INSTRUCTIONS
B
Push tabs on Toe into slots on Bottom Shelf .
Tabs and slots must be lined up correctly or they will
not properly tighten.
1B
A
Turning the part upright push down on Toe until
A
B
2
Talk to our customer service agent at:
[phone]
Watch our assembly video at:
sprout-kids.com/bmsa
A
B
A
If using an alternative base option please refer
*
Flip Casters (pg. 7)
Tapered Legs (pg. 10)
Locking Casters (pg. 10)

DOCUMENT: AI-B.2-NoBack WWW.SPROUT-KIDS.COM COPYRIGHT QUARK ENTERPRISES 2018 PAGE 5 OF 12
4Insert Back tabs into matching slots in Side .
A Full Back comes as one piece. A Split Full Back
comes in two pieces that share the middle slot when
inserted.
F
F
F
D
D
BB
3Pop the tabs on Top Shelf C and Bottom Shelf B into
corresponding slots on Left Side D , as shown. Left Side
slots will not be visible if Shelves are installed correctly.
A second adult is needed to hold shelves in place.
B
As one adult holds the back and shelves steady, insert
bottom slots on Right Side into the tabs on Bottom
Shelf .
B
B
C
C
D
5
E
E
B
D
II
TIGHTEN
SLIGHTLY
I
C
NOTCH
WIDE LIP
SLOTTAB

QUARK ENTERPRISES, LLC PO BOX 1123, PROVO, UT 84601 MODEL NO. BMSPAGE 6 OF 12
With the help of a second person, insert tabs on Back
and Top into slots in Side .
F
F
7
Carefully tip shelving unit onto its back on a hard
D
B
B
B
C
6
C
C
C
8
Carefully set shelving unit upright. Insert Pins into
holes at the desired height and rest Shelf on pins.
E
E
E
E
G
G
H
H
D

DOCUMENT: AI-B.2-NoBack WWW.SPROUT-KIDS.COM COPYRIGHT QUARK ENTERPRISES 2018 PAGE 7 OF 12
HARDWARE INSTALLATION
Adult assembly only
Drill/power screwdriver required for assembly
A
B
Casters (4)
Caster Screws (4 per caster)
Toe (2) U-Bend (2)
(1 on each end)
Parts
Flip Casters
D
C
F
Left Side (1) Right Side (1)
E
A
ASSEMBLY INSTRUCTIONS
1The Toe has two pre-drilled holes on each
end. Align Castor as shown.
C
USE THIS HOLE
C
A
C
A
C

QUARK ENTERPRISES, LLC PO BOX 1123, PROVO, UT 84601 MODEL NO. BMSPAGE 8 OF 12
2
across from it. Continue until all four screws
are in place, rotating the wheel out of the
way as you go.
For the rest of the steps have a second adult
hold any upright parts steady until assembly is
complete.
*
3Insert one Toe into Right Side with
U-Bends at the bottom as shown. Use
hammer to ensure complete insertion.
D
CF
D
D
C
F

DOCUMENT: AI-B.2-NoBack WWW.SPROUT-KIDS.COM COPYRIGHT QUARK ENTERPRISES 2018 PAGE 9 OF 12
4Rotate Toe to the “Locked” postition,
with Castors facing inwards.
A
5Repeat Steps 3 & 4 for other Toe.
Proceed with standard Assembly Instructions,
ignoring Steps 1 & 2.
*
C
A
C
A

10
QUARK ENTERPRISES, LLC PO BOX 1123, PROVO, UT 84601 MODEL NO. BMSPAGE 10 OF 12
ASSEMBLY INSTRUCTIONS
Parts
Bottom Shelf (1)
Casters (4)
Caster Screws (4 per caster)
c
Locking Casters
ASSEMBLY INSTRUCTIONS
Parts
Tapered Legs
A
2Line up holes in Casters with pilot holes
in Bottom Shelf . Use the drill to screw
Caster Screws into pilot holes. Then
screw in remaining 8 Caster Screws .
A
A
A
B
B
BB
B
C
C
with pilot holes facing up.
C
C
1
C
A
Feet (4)
B
B
Bottom Shelf (1)
A
Screw the Feet into the Bottom Shelf
until tight as shown below.
1B
A
A
Proceed with standard Assembly Instructions,
ignoring Steps 1 & 2.
*
Proceed with standard Assembly
Instructions, ignoring Steps 1 & 2.
*
PILOT HOLES
FOR CASTERS

Simple. Modern. American Made.
QUARK ENTERPRISES, LLC PO BOX 1123, PROVO, UT 84601 MODEL NO. BMSPAGE 12 OF 12