Belshaw Brothers Heat & Ice H&I-2 User manual

Belshaw Bros., Inc.
814 44th Street NW, Suite 103
Auburn, WA 98001 USA
Tel: [phone]
Fax: [phone]
Toll Free (US): 1-800-578-2547
E-mail: [e-mail]
www.belshaw.com
Operator’s Manual
and
Technical Supplement
Heat & Ice
H&I-2, H&I-4, H&I-6, IGT

Belshaw Bros., Inc. •www.belshaw.com •Phone [phone] •Fax [phone]
H&I All Models OM MN-1731EN iii
Contents
1 Operation 1
Initial setup 1
2 Cleaning 2

Belshaw Bros., Inc. •www.belshaw.com •Phone [phone] •Fax [phone]
iv MN-1731EN H&I All Models OM
Preface
The H&I Heat and Ice is designed for icing
donuts and a variety of baking products quickly
and easily.
It is meant to be used on a flat surface. The
operator must work safely at all times, read this
manual, and follow its instructions and warnings.
The H&I Heat and Ice uses electrical elements to
heat water in its kettle. The machine is available
with the following electrical configurations:
•120 volts, 1 phase, 50/60 hertz
•240 volts, 1 phase, 50/60 hertz
To use the H&I Heat and Ice safely, heed the
following warnings:
•Disconnect from power source before
cleaning or repairing.
•Never touch the icing pan once the
machine is on. The pan gets very hot,
which may cause serious burns.
•Do not overfill the kettle with water.
•Hot water can cause serious burns.
Make sure that the system and the water
are cool before attempting any
adjustment, repair, disassembly, or
cleaning.
•To avoid electrocution or other injury,
unplug the machine before attempting
any adjustment, repair, disassembly, or
cleaning.
•To avoid damaging the machine, never
use force to assemble, disassemble,
operate, clean, or maintain it.
•Be careful never to get water, or other
materials on the floor. If anything does
get spilled on the floor, mop it up
immediately. Materials on the floor can
cause people to slip or fall, resulting in
serious injury or loss of life.
•To prevent unintentional startup and
possible fire, unplug the machine if there
is a local power outage. When the
power is restored, it is safe to plug the
machine in again.
•To avoid electrocution, make sure that
all electrical cords are not frayed or
cracked and that they do not pass
through any water.
•Make sure that all electrical cords are
routed so that no one will trip over them.

Belshaw Bros., Inc. •www.belshaw.com •Phone [phone] •Fax [phone]
H&I All Models OM MN-1731EN 1
1 Operation
Figure 1. H&I-4
WARNING
Do not operate without proper water level.
This will prevent damage to the heater
element.
WARNING
Do not submerge the heating element or
control box with water.
Initial setup
1. Remove H&I from box.
2. Remove all packing materials.
3. Wash H&I with warm water and a mild
detergent.
4. Sanitize H&I
5. Install one empty icing bowl.
6. Fill kettle with hot water until the empty
icing bowl is floating ½ in. off the cover.
7. Install the remaining bowls, lids and
thermometer to the kettle
8. Plug in H&I
NOTE
Use hot water to fill the H&I, using cold
water can take up to 8 hours to heat up to
120°F.
9. Turn on power switch.
10. Set thermostat dial for desired icing
temperature.
NOTE
Final setting will vary depending on
desired icing temperature
NOTE
Do not turn H&I off overnight; H&I can
take up to 8 hours to reheat

Belshaw Bros., Inc. •www.belshaw.com •Phone [phone] •Fax [phone]
2 MN-1731EN H&I All Models OM
2 Cleaning
For your safety, observe the following warnings
throughout the entire cleaning process.
WARNING
Thoroughly clean and dry the floor if
glaze, water, or other materials are spilled.
Materials spilled on the floor can cause
serious injury or loss of life
WARNING
To avoid the possibility of shock, unplug
the unit before cleaning
Once per week, clean as explained below.
WARNING
To avoid being burned, wait for icing pan
to cool before removing
1. Unplug the unit. Remove any debris from
the work area before disassembling the
H&I.
2. Remove bowls, lid and thermometer and
wash with warm soapy water, rinse and
wipe dry.
3. Drain water from kettle, using the drain
valve on the back of the machine.
IMPORTANT
To avoid damage to the wire / frame, use
caution when removing and transporting
the wire / frame
4. Clean the H&I with warm water and mild
cleaner.
5. Sanitize the H&I
6. Install one empty icing bowl.
7. Fill kettle with hot water until the empty
icing bowl is floating ½ in off the cover.
8. Return the remaining bowls, lids and
thermometer to the kettle
9. Plug in H&I
10. Turn on power switch.
IMPORTANT
Do not hose down electrical components

Heat & Ice
H&I-2, H&I-4, H&I-6, IGT
Technical Supplement
Belshaw Bros., Inc.
814 44th Street NW, Suite 103
Auburn, WA 98001 USA
Phone: +-1-206-322-5474 • Fax: +-1-206-322-5425
Email: [email protected] • http://www.belshaw.com

Belshaw Bros., Inc. •www.belshaw.com •Phone [phone] •Fax [phone]
H&I All Models MN-1731EN iii
Contents
1 Installation 1
2 Maintenance 2
3 Troubleshooting 3
4 Appendix 4
Parts List Drawing Insert Page Insert

Belshaw Bros., Inc. •www.belshaw.com •Phone [phone] •Fax [phone]
iv MN-1731EN H&I All Models
Preface
The H&I Heat and Ice is designed for icing
donuts and a variety of baking products quickly
and easily.
It is meant to be used on a flat surface. The
operator must work safely at all times, read this
manual, and follow its instructions and warnings.
The H&I Heat and Ice uses electrical elements to
heat water in its kettle. The machine is available
with the following electrical configurations:
•120 volts, 1 phase, 50/60 hertz
•240 volts, 1 phase, 50/60 hertz
To use the H&I Heat and Ice safely, heed the
following warnings:
•Disconnect from power source before
cleaning or repairing.
•Never touch the icing pan once the
machine is on. The pan gets very hot,
which may cause serious burns.
•Do not overfill the kettle with water.
•Hot water can cause serious burns.
Make sure that the system and the water
are cool before attempting any
adjustment, repair, disassembly, or
cleaning.
•To avoid electrocution or other injury,
unplug the machine before attempting
any adjustment, repair, disassembly, or
cleaning.
•To avoid damaging the machine, never
use force to assemble, disassemble,
operate, clean, or maintain it.
•Be careful never to get water, or other
materials on the floor. If anything does
get spilled on the floor, mop it up
immediately. Materials on the floor can
cause people to slip or fall, resulting in
serious injury or loss of life.
•To prevent unintentional startup and
possible fire, unplug the machine if there
is a local power outage. When the
power is restored, it is safe to plug the
machine in again.
•To avoid electrocution, make sure that
all electrical cords are not frayed or
cracked and that they do not pass
through any water.
•Make sure that all electrical cords are
routed so that no one will trip over them.

Belshaw Bros., Inc. •www.belshaw.com •Phone [phone] •Fax [phone]
H&I All Models MN-1731EN 1
1 Installation
NOTE: Picture depicts H&I-4 only
WARNING
Do not operate without proper water level.
This will prevent damage to the heater
element.
WARNING
Do not submerge the heating element or
control box with water.
Initial setup
1. Remove H&I from box.
2. Remove all packing materials.
3. Wash H&I with warm water and a mild
detergent.
4. Sanitize H&I
5. Install one empty icing bowl.
6. Fill kettle with hot water until the empty
icing bowl is floating ½ in. off the cover.
7. Install the remaining bowls, lids and
thermometer to the kettle
8. Plug in H&I
NOTE
Use hot water to fill the H&I, using cold
water can take up to 8 hours to heat up to
120°F.
9. Turn on power switch.
10. Set thermostat dial for desired icing
temperature.
NOTE
Final setting will vary depending on
desired icing temperature
NOTE
Do not turn H&I off overnight; H&I can
take up to 8 hours to reheat

Belshaw Bros., Inc. •www.belshaw.com •Phone [phone] •Fax [phone]
2 MN-1731EN H&I All Models
2 Maintenance
There is no maintenance required for the H&I-2, H&I-4, or IGT models.

Belshaw Bros., Inc. •www.belshaw.com •Phone [phone] •Fax [phone]
H&I All Models MN-1731EN 3
3 Troubleshooting
If you have a problem with your H&I that you
cannot solve, call your dealer or another
qualified technician.
If your dealer cannot help you, please call
Belshaw Bros. at [phone]. When you
call, please specify the following:
•The model name of the machine.
•The serial number of the machine.
•The voltages, phase, and cycle of the
machine.
CAUTION
If you perform repairs yourself or have
them performed by anyone other than a
service technician authorized by Belshaw
Bros., you do so at your own risk.
WARNING
Disconnect the machine from the power
source before disassembling, repairing, or
wiring.