Benning TA 6 User manual

BENNING TA 6
Operating manual
Translation of the German original version
5190 / 04/2021 en

Legal notice
5190 / 04/2021 enBENNING TA 62
Legal notice
Notes concerning the documentation
Ensure that the applicable documentation is used for this product. For safe handling, knowledge
that is provided in these instructions is required.
The product may only be handled while following this documentation, particularly the safety
instructions and warnings it contains. The personnel must be qualified for the respective task
and have the capability to recognise risks and prevent possible dangers.
Manufacturer and holder of rights
BENNING Elektrotechnik und Elektronik GmbH&Co.KG
Münsterstraße135–137
46397 Bocholt
Germany
Phone: +492871/93‑0
E-Mail: [email protected]
Internet: www.benning.de
Commercial register Coesfeld HRA No. 4661
Copyright
© 2021, BENNING Elektrotechnik und Elektronik GmbH&Co.KG
All rights reserved.
This document – particularly all of the contents, texts, photographs and graphics that it contains
– are protected by copyright.
No part of this documentation or the associated contents may be reproduced or edited, copied
or distributed using electronic media in any form (printed, photocopied or using any other
method) without express written permission.
Disclaimer
The contents of the documentation has been checked to ensure that it corresponds to the
hardware and software described. Nevertheless, deviations cannot be ruled out, so Benning
cannot guarantee complete correspondence. The contents of this documentation are checked
at regular intervals, and any corrections that are needed are contained in the versions that
follow.
General non-discrimination
Benning is aware of the importance of language with regard to the equality of men and women,
and endeavours to take this into account at all times. To improve readability, we have refrained
from consistently using differentiating formulations.

Table of contents
Table of contents
1 Introduction................................................................................................................................................6
1.1 General notes........................................................................................................................6
1.2 History ...................................................................................................................................7
1.3 Service & support..................................................................................................................8
2 Safety..........................................................................................................................................................9
2.1 Warning system ....................................................................................................................9
2.2 Standards applied .................................................................................................................9
2.3 Symbols used......................................................................................................................10
2.4 Intended use .......................................................................................................................11
2.5 Special types of risks ..........................................................................................................12
3 Scope of delivery.....................................................................................................................................13
4 Device description...................................................................................................................................14
4.1 Device structure ..................................................................................................................14
4.2 Functions.............................................................................................................................15
5 Operation..................................................................................................................................................16
5.1 Testing with an installation tester ........................................................................................16
6 Maintenance.............................................................................................................................................17
6.1 Cleaning the device.............................................................................................................17
7 Technical data..........................................................................................................................................18
8 Disposal and environmental protection ................................................................................................19
Index .........................................................................................................................................................20
5190 / 04/2021 en BENNING TA 6 3

Table of figures
Table of figures
Figure 1 BENNINGTA6 device structure ...................................................................................................... 14
Figure 2 Switch positions of the BENNINGTA6 ............................................................................................ 15
Figure 3 Connecting the BENNINGTA6........................................................................................................ 16
5190 / 04/2021 enBENNING TA 64

List of tables
List of tables
Table 1 History............................................................................................................................................... 7
Table 2 Symbols on the device...................................................................................................................... 10
Table 3 Symbols used in the operating manual............................................................................................. 10
Table 4 Technical data .................................................................................................................................. 18
5190 / 04/2021 en BENNING TA 6 5

1.1 General notes
Introduction
5190 / 04/2021 enBENNING TA 66
1 Introduction
The BENNINGTA6 measuring adapter described here (in the following only referred to as
“device”) is an optional accessory for the BENNINGIT115, IT130 and IT200 installation
testers. The BENNINGTA6 measuring adapter enables you to perform tests on electrical
installations in compliance with DINVDE0100‑600 (IEC60364‑6) and DINVDE0105‑100
(EN50110) using the corresponding installation tester.
The device ensures safe contact between the BENNING installation tester and the 5-pin 16A
CEEsocket (3P/ N/ PE, 400V, 50Hz) of the electrical installation.
The device supports the following measurements:
• Insulating resistance measurement RISO (L1‑PE, L2‑PE, L3‑PE, N‑PE, L1‑L2, L2‑L3, L3‑L1)
• Loop impedance measurement ZLOOP (L1‑PE, L2‑PE, L3‑PE)
• Line impedance measurement ZLINE (L1‑N, L2‑N, L3‑N, L1‑L2, L2‑L3, L3‑L1)
• RCDtesting
• Phase sequence test, voltage and frequency measurements
Further information
http://tms.benning.de/ta6
On the Internet, you will find the following additional information directly at the specified link or
at www.benning.de (product search):
• Operating manual of the device in several languages
• Further information depending on the device (e.g. brochures, technical reports, FAQs)
1.1 General notes
Target group
This operating manual is intended for the following groups of people:
• Qualified electricians and qualified technical personnel
Required basic knowledge
To understand these operating manual, you will need general knowledge of testing and
measuring equipment. Moreover, you will need basic knowledge of the following issues:
• General electrical engineering
Purpose of the operating manual
This operating manual describes the device and provide you information about how to handle it.
Keep this operating manual in a safe place for later use. Read this operating manual before
handling the device and follow the instructions.

Introduction
1.2 History
5190 / 04/2021 en BENNING TA 6 7
NOTE
Disclaimer of liability
Please make sure that any person using the device has read and understood the instructions of
this operating manual before handling the device and that the instructions are adhered to in all
points. Non-observance of this operating manual might result in product damage, property
damage and/or personal injury.
Benning assumes no liability for damage and malfunctions resulting from the failure to observe
the instructions in this operating manual.
The devices are subject to continuous further development. Benning reserves the right to make
changes to the device’s design, configuration and technology. The information in this operating
manual corresponds to the state of technical knowledge at the time of printing. For this reason,
no claims for certain device characteristics can be derived from the contents of this operating
manual.
Information in this operating manual can be changed at any time without prior notice. Benning is
not obligated to make amendments to this operating manual or to keep it up to date.
Direct any technical questions to Technical Support [}page8].
Trademarks
All trade marks that are used are the property of their respective owners, even if they are not
separately marked as such.
1.2 History
Release number Amendments
04/2021 • Initial release
Table1: History

1.3 Service & support
Introduction
5190 / 04/2021 enBENNING TA 68
1.3 Service & support
Please contact your specialty retailer or the BENNINGServiceCenter for any repair or service
work that might be required.
Technical support
Please contact our Technicalsupport for technical questions on handling the device.
Phone: +49287193-555
Fax: +49287193‑6555
E-Mail: [email protected]
Internet: www.benning.de
Returns management
Easily and conveniently use the BENNING returns portal for a quick and smooth returns
processing:
https://www.benning.de/service-de/retourenabwicklung.html
Phone: +49287193-554
E-Mail: [email protected]
Return address
BENNING Elektrotechnik und Elektronik GmbH & Co. KG
Retourenmanagement
Robert-Bosch-Str. 20
D - 46397 Bocholt

Safety
2.1 Warning system
5190 / 04/2021 en BENNING TA 6 9
2 Safety
2.1 Warning system
This operating manual contains notes that must be taken into consideration for your personal
safety and in order to avoid injuries and damage to property. Warnings about your personal
safety and to prevent personal injuries are marked with a warning triangle. Warnings on sole
prevention of material damage are shown without a warning triangle. The warnings are shown
in descending order depending on the hazard level as follows.
DANGER
Extremely dangerous situation for humans
If you do not pay attention to this warning, irreversible or deadly injuries will occur.
WARNING
Hazard to humans
If you do not pay attention to this warning, irreversible or deadly injuries could occur.
CAUTION
Minor hazard to humans
If you do not pay attention to this warning, minor or moderate injuries could occur.
NOTICE
Danger to property, not to persons
If you do not pay attention to this warning, material damage could occur.
If multiple hazard levels occur, the warning for the highest respective hazard level will be used.
In addition, a warning about personal injuries can also include a warning about material
damage.
2.2 Standards applied
The device has been built and tested in compliance with the following standards and has left the
factory in perfectly safe condition.
• IEC/ DINEN 61010-031 (VDE0411‑031)

2.3 Symbols used
Safety
5190 / 04/2021 enBENNING TA 610
2.3 Symbols used
Symbols on the device
Symbol Meaning
Please observe the information provided in this operating manual in
order to avoid dangers.
CATII Measuring categoryII is applicable to testing and measuring circuits
which are directly connected to user connections (e.g. sockets) of the
low-voltage mains installation.
The device complies with EUdirectives.
At the end of product life, dispose of the unserviceable device via
appropriate collecting facilities provided in your community.
The device is provided with protective insulation (protection classII).
Please observe the operating manual.
Table2: Symbols on the device
Symbols used in the operating manual
Symbol Meaning
General warning
Warning of electric voltage!
(AC) alternating voltage or alternating current
Earth (voltage to earth)
Table3: Symbols used in the operating manual

Safety
2.4 Intended use
5190 / 04/2021 en BENNING TA 6 11
2.4 Intended use
Only use the device within the framework of the corresponding technical data. Any operating
conditions that deviate from this shall be considered as improper use. Solely the user of the
device shall be liable for any resulting damage.
In particular, note the following:
• In case of improper use, the liability and warranty claims become void. Solely the user of the
device shall be liable for any damage resulting from improper use. Uses not complying with
the intended use include e.g.:
– Use of components, accessories, spare or replacement parts that have not been
released and approved for the respective application by Benning
– Non-observance, manipulation, changes or misuse of the operating manual or the
instructions and notes contained therein
– Any form of misuse of the device
– Any use other than or beyond that described in this operating manual
• Warranty and liability claims are generally excluded if damage is due to force majeure.
• If any prescribed services are not performed regularly or not on time according to
manufacturer specifications during the warranty period, a decision about a warranty claim
can only be made once the findings are available.
Direct any questions to Technical Support [}page8].
Using the device
Please observe the following basic obligations when using the device:
• The device may only be used in a technically perfect and safe condition. Always check the
device for damages before using it.
• Make sure the personnel using the device is qualified for the respective task.
• Observe relevant regulations on occupational safety and health as well as those on
environmental protection.
• The device may only be used in dry environments.
• Use the device exclusively for measuring purposes with the BENNINGIT115, IT130 and
IT200 installation testers. In addition, observe the operating manual of the installation
tester.
• The device is intended for short-time use only (continuous operation is not permitted).
Disconnect the device from the test object after use.
• Use the device only in electric circuits of overvoltage categoryII with a conductor for a
maximum of 300V to earth.
WARNING
Opening the device
Danger to life or serious injury is possible due to contact with high electric voltage when opening
the device. The device might get damaged.
• Do not open the device.
• Please contact your specialty retailer or the returns management [}page8] for any repairs.

2.5 Special types of risks
Safety
5190 / 04/2021 enBENNING TA 612
Securing the device
If the device is not in a technically perfect and operationally safe condition, safe operation is no
longer guaranteed. Make sure that the following measures are taken:
• Switch off the device.
• Remove the device from the measuring point.
• Secure the device against unintentional operation.
The following characteristics indicate that safe operation is no longer guaranteed:
• The device (housing, cables or plugs) shows visible damage or is damp/wet.
• The device does not work properly in compliance with regulations (e.g. errors during
measurements).
• The device shows recognisable consequences of prolonged storage under inadmissible
conditions.
• The device shows recognisable consequences of extraordinary stress due to transport.
2.5 Special types of risks
WARNING
Dangerous voltage
Danger to life or serious injury is possible due to contact with high electric voltage when working
on live components or equipment. Even low voltages from 30V‑AC and 60V‑DC on can be
dangerous to human life!
• Please observe relevant regulations on occupational safety and health.
• If necessary, use appropriate protective equipment.

Scope of delivery
2.5 Special types of risks
5190 / 04/2021 en BENNING TA 6 13
3 Scope of delivery
The scope of delivery of the device includes the following components:
• 1x BENNINGTA6 measuring adapter
• 1x operating manual

4.1 Device structure
Device description
5190 / 04/2021 enBENNING TA 614
4 Device description
4.1 Device structure
1
3
4
5
6
2
Figure1: BENNINGTA6 device structure
1 Housing 2 Rotary switch
3 Test cable 4 16A CEEplug (3P/ N/ PE, 400V,
50Hz, 5‑pin)
5 Connecting plug 6 Connecting cable

Device description
4.2 Functions
5190 / 04/2021 en BENNING TA 6 15
4.2 Functions
The device supports the following measurements:
• Insulating resistance measurement RISO (L1‑PE, L2‑PE, L3‑PE, N‑PE, L1‑L2, L2‑L3, L3‑L1)
• Loop impedance measurement ZLOOP (L1‑PE, L2‑PE, L3‑PE)
• Line impedance measurement ZLINE (L1‑N, L2‑N, L3‑N, L1‑L2, L2‑L3, L3‑L1)
• RCDtesting
• Phase sequence test, voltage and frequency measurements
Switch positions
1
2
3
4
5
Figure2: Switch positions of the BENNINGTA6
1 Rotary switch 2 4switch positions for insulating
resistance measurement RISO (L1‑PE,
L2‑PE, L3‑PE, N‑PE)
3 1switch position for phase sequence
test, voltage and frequency
measurements
4 3switch positions for line impedance
measurement ZLINE and insulating
resistance measurement RISO (L1‑L2,
L2‑L3, L3‑L1)
5 3switch positions for line impedance
measurement ZLINE, loop impedance
measurement ZLOOP, RCD testing and
insulating resistance measurement RISO
(L1‑N/PE, L2‑N/PE, L3‑N/PE)

5.1 Testing with an installation tester
Operation
5190 / 04/2021 enBENNING TA 616
5 Operation
You can perform tests with an installation tester.
5.1 Testing with an installation tester
Requirements
• Installation tester BENNINGIT115, IT130 or IT200
• Please observe the operating manual of the installation tester used (especially the safety
instructions and warnings contained therein).
• Test object compatible with the device (16A CEEsocket, 3P/ N/ PE, 400V, 50Hz, 5‑pin)
NOTE
Insulating resistance
Measurements of the insulating resistance must be carried out only at test objects which are
free of voltage.
1 2 3
Figure3: Connecting the BENNINGTA6
1 BENNING installation tester 2 BENNINGTA6
3 Test object
Procedure
1. Connect the connecting plug of the device to the test connection of the installation tester.
2. Connect the 16ACEEplug of the device to the test object.
3. Set the desired measuring function on the installation tester.
4. Set the corresponding switch position on the rotary switch of the device.
5. Start the measurement on the installation tester.
6. After having carried out the measurement, save the measuring result (optional).
7. Repeat the described procedure for further intended measurements on the test object.
8. Disconnect the device from the test object after having completed the measurements.

Maintenance
6.1 Cleaning the device
5190 / 04/2021 en BENNING TA 6 17
6 Maintenance
There are no components in the device that you can replace.
WARNING
Opening the device
Danger to life or serious injury is possible due to contact with high electric voltage when opening
the device. The device might get damaged.
• Do not open the device.
• Please contact your specialty retailer or the returns management [}page8] for any repairs.
6.1 Cleaning the device
Clean the device regularly and as the need arises.
Requirements
• A clean and dry cloth or special cleaning cloth
NOTICE
Wrong cleaning agents
Using the wrong cleaning agents can damage the device.
• Do not use any solvents, abrasives or polishing agents.
Procedure
Clean the exterior of the device with a clean and dry cloth or a special cleaning cloth.

6.1 Cleaning the device
Technical data
5190 / 04/2021 enBENNING TA 618
7 Technical data
Input voltage Up to 430V (three-phase)
Frequency 50Hz, 60Hz
Protection class II (double insulation)
Contamination level 2
Protection category
(DINVDE0470‑1, IEC/ EN60529)
IP40
1stdigit: 4= protection against granular foreign
objects
2nddigit: 0= no protection against water
Overvoltage category CATII 300V to earth
Housing dimensions
(lengthx widthx height)
145mmx 85mmx 70mm
Length of test cable 1.5m
Weight 0.5kg
Operation
Operating duration Short-term use (no continuous operation)
Max. barometric altitude 2 000m
Operating temperature 0…40°C
Max. relative air humidity 95%RH (0…40°C), non-condensing
Storage
Ambient temperature -10…70°C
Max. relative air humidity 90%RH (-10…40°C)
80%RH (40…60°C)
70%RH (60…70°C)
Table4: Technical data

Disposal and environmental protection
6.1 Cleaning the device
5190 / 04/2021 en BENNING TA 6 19
8 Disposal and environmental
protection
At the end of product life, dispose of the unserviceable device via appropriate
collecting facilities provided in your community.

Index
Index
B
Basic knowledge 6
BENNING TA 6 6
C
Cleaning 17
Copyright 2
D
Device
Cleaning 17
Securing 12
Disclaimer 2, 11
Disposal 19
Documentation 2
E
Environmental protection 19
F
Further information 6
H
History 7
Holder of rights 2
I
Intended use 11
M
Maintenance 17
Manufacturer 2
N
Non-discrimination 2
P
Purpose of the operating manual 6
R
Return address 8
Returns management 8
S
Scope of delivery 13
Securing 12
Service & Support
Technical support 8
Standards applied 9
Switch positions 15
Symbols
Device 10
Operating manual 10
T
TA 6 6
Target group 6
Technical data 18
Technical support 8
Testing
With an installation tester 16
Trademarks 7
W
Warning system 9
Warranty 11
5190 / 04/2021 enBENNING TA 620