BERNSTEIN DPG5019 User manual

REGENDUSCHE EDELSTAHL DPG5019
RAINFALL CEILING SHOWER DPG5019
POMMEAU DE DOUCHE PLUIE DPG5019
SOFFIONE A SOFFITTO DPG5019
MONTAGEANLEITUNG - I / 2018
ASSEMBLY INSTRUCTIONS / NOTICE DE MONTAGE / ISTRUZIONI DI MONTAGGIO

2
DPG5019
Les renseignements gurant dans cette notice de montage ne sont communiqués qu’à titre d’information et peuvent être
mis à jour sans préavis. Toutes les gures et dessins présents dans ces instructions sont uniquement à titre d’illustration
et n’ont aucune valeur d‘actualité.
This instructions should only be considered as a standard manual. Modications applied to updated version of the pro-
duct might not be mentioned inside this document. In this case, please just use the manual as a reference. The company
reserves modication rights.
Il seguente manuale è solo una guida standard. Nel caso in cui dovessero essere presenti errori, dovuti a eventuali modi-
che postume del prodotto, si prega di considerare il manuale unicamente come riferimento per il montaggio. L´azienda
si riserva il diritto di modica.
ERKLÄRUNG
STATEMENT
EXPLICATIONS
DICHIARAZIONE
Die Bedienungsanleitung dient nur als Referenz. Diese Anleitung kann abweichende Angaben enthalten.
Die beschriebenen Produkte können jederzeit aktualisiert werden. Die Zeichnungen in dieser Anleitung dienen nur zur
Darstellung und haben keinen Anspruch auf Aktualität.

3
DPG5019
Draw and drillfour holes on the wall.
Insert plastic expansile screw.Turn the screw clockwise.
Adjust the expansion link. Make sure the holder is
at the same line with ceiling.
Bottom view

4
DPG5019
FILL VALVE INSTALLATION
1. WORK PREPARATION
Remove the inoperative tank ttings and carefully clean the water cistern/tank.
Make sure all debris has been removed prior to installing new tank ttings.
WARNING
Do notuse or drop any chlorine or any chemical related components. Use of such products will:
Result in damage to tank components and may cause ooding and property damage and void warranty.
Do not overtighten nuts, or tank/bowl may crack.
2. FILL VALVE INSTALLATION AND WATER LEVEL ADJUSTMENT
1. Please read carefully the following installation instructions in
order to avoid component damage or injury to the installer.
2. The instructions have been composed based in the latest product
specications. We reserve the right to make modications to the
packaging and specications without providing prior notication.
3. When installing the ll valve,the critical level on the ll valve
(identied on the valve marked ”CL”) should be at least 1”)
above the top of the overow pipe of the ush valve.This is a
plumbing code.
4. We shall not be responsible for failures that are contributed to the
use of parts other than those specied.
5. Water Temperature: 2°C to 45°C.
6. Water Pressure Range: 0.2 Bar to 8 Bar.
Rell tube
overow pipe
bracket
bracket
bolt
overow
pipe
tank overow
pipe
water supply
pipe
inlet adaptor
water supply
switch
screw rod
bolt
1. Unscrew the bracket bolt and locate/install the ll valve onto overow pipe of ush valve.
2. Then tighten the bracket bolt.
3. Connect water supply into inlet shank , turn on the water supply valve (angle stop) (Make sure that rell tube has
been inserted in the ush valve overow pipe in the event the toilet requires rell to the bowl).
4. Check if the inlet valve is under normal operation and adjust the inlet valve oat adjustment thumbscrew clockwise
(for higher oat & water level) or anticlockwise (for lower oat & water level) according to the requirements.
u v w x

5
DPG5019
4. TROUBLESHOOTING
Issue - Cause - Resolution
Water line is too high or too low.
Inlet valve is not adjusted to a suitable position. Adjust the water level to the appropriate water level.
Inlet valve does not shut off.
The cistern/tank wall has blocked the movement of the inlet valve oat. Adjust the ll valve and make sure oat can move freely.
The rell tube wasn’t installed properly. See gure attached 3.7 to re-install rell tube correctly.
Leakage of ush valve. Make sure none leakage of ush valve.
The water level is above overow pipe of ush valve. Re-adjust water level to appropriate.
Inlet valve does not turn on.
Water supply valve/angle stop is off. Turn on the water supply valve/angle stop.
The cistern/tank wall has blocked the movement of the inlet valve oat. Adjust the ll valve and make sure oat can move freely.
Filter screen is dirty. Clean lter screen.
3. CLEANING FILTER (Filter which is located inside the inlet valve shank is required for cleaning periodically).
inlet connector
bracket
water supply
pipe
water supply
pipe
Wrongly placed rell tube
Adjust rell tube, make sure tube
is above the water line.
water level
tank
tank
overow
pipe
lter
lter
inlet connector
inlet connector
water
supply switch
water
supply switch
nut
nut
lter
bolt
1. Shut off the water supply valve (angle stop) then remove the water supply line from the inlet adaptor.
2. Unscrew the bracket bolt and remove the ll valve.
3. Unscrew ll valve nut, remove inlet connector, nut and lter.
4. Clean the lter screen with water.
5. Install back the clean lter and inlet connector.
(Note: The opening of inlet connector goes into the inlet body and screw up the nut).
6. Reference point two of „FILL VALVE INSTALLATION AND ...“ to re-install the ll valve and turn on water supply.
u v w
y
x
z{