Best DD0130SS User manual

SPECIFICATION SHEET
REFERENCE QTY. REMARKS Project
Location
Architect
Engineer
Contractor
Submitted by Date
Exhaust your cooktop without the use of an
overhead hood. Compact design is installed directly
behind cooktop.
FEATURES
HOUSING:
•Rugged steel construction
•Finished with silver paint
•Space-saving - can be used with most cooktops on the
market
•30", 36", or 48" widths - Fits standard-size cabinets
BLOWER:
•Dynamically-balanced 9-1/8" dia. x 2-1/8" centrifugal
blower wheel for quiet, efficient performance
•Permanently lubricated, thermally-protected motor
•Neoprene, resilient anti-vibration mounts
•Unit plugs directly into 120 VAC, 60 HZ, grounded outlet
•Uses standard 3-1/4" x 10" duct connector
•3-position discharge - scroll box moveable to adjust to
floor joists
CHIMNEY ASSEMBLY:
•Brushed stainless steel cover - just press button to turn
unit "ON"
•Chimney rises 9½" when activated - ideal for large pots
and pans
•Stylish, stainless steel filters with aluminum mesh - easy
to remove and dishwasher-safe
•Stainless steel chimney front and back - makes cleanup
quick and easy
•Top cover-mounted, 3-speed control, with delay off and
clean filter reminder
•Heat Sentry adjusts speed of blower in case of excess
heat
•Conveniently located button - press to lower air vent and
turn unit "OFF"
•Remote Control activates downdraft from alternate loca-
tion
TYPICAL SPECIFICATION
Downdraft blower system shall be Best®Model DD0130SS
(DD0136SS) (DD0148SS).
Unit to have steel housing with silver paint finish. Air vent to
rise at least 9½" and have a stainless steel front and back for
ease of cleaning.
Filters to be stainless steel with aluminum mesh, easy to
remove and dishwasher-safe.
Blower will connect directly to 3¼" x 10" rectangular duct (6"
round duct using a transition). Blower discharge to be
convertible to accommodate ductwork from LEFT, RIGHT, or
BELOW and have 7½" side-to-side adjustment.
Motor shall be mounted to blower assembly with grease
resistant anti-vibration mounts, be removable, and lifetime
lubricated.
Unit to include Heat Sentry, to adjust blower speed in case
of excess heat.
Unit to include remote control activation button.
Downdraft system shall operate on 120 VAC and be able to
be plugged into a standard grounded outlet. It will have a 3-
speed blower control, with delay off, and clean filter re-
minder.
Air delivery shall be no less than 500 CFM. Air delivery rating
shall be certified by HVI. Downdraft blower system to be U.L.
listed.
SPECIFICATIONS
VOLTS AMPS CFM DUCT
120 4.0 500 3-1/4" x 10"
MODELS DD0130SS, DD0136SS,
DD0148SS
DOWNDRAFT
50H 99043191B
HVI2100 CERTIFIED RATINGS comply with
new testing technologies and procedures
prescribed by the Home Ventilating Institute,
for off-the-shelf products, as they are available
to consumers. Product performance is rated at
0.1 in. static pressure, based on tests
conducted in AMCA’s state-of-the-art test
laboratory. Sones are a measure of humanly-
perceived loudness, based on laboratory
measurements.
Best by Broan, P.O. Box 140, Hartford, WI 53027

INSTALLATION PLANNING • MODELS DD0130SS, DD0136SS, DD0148SS
DIMENSIONS
NOTE: Dimensions shown are for reference only. Before cutting
out countertop, refer to instructions packed with downdraft and
cooktop.
ELECTRICAL
The unit has an 18-in. power cord with a 3-pronged plug. Plan to
provide a grounded outlet within reach of this cord.
DOWNDRAFT
TYPICAL INSTALLATION
COOK TOP
CHIMNEY TOP
COUNTER
TOP
GEAR
MOTOR
COVER
BLOWER
BOX
3-1/4" X 10"
DUCT CONNECTOR
AIR
VENT
120 VAC
GOUNDED
OUTLET
CABINET
FRONT
DUCTWORK
This downdraft blower system is designed for use with 3¼" x 10"
rectangular, or 6" round duct. The blower discharge can be
positioned in one of 3 directions with 7½" movement side to side.
Refer to the cooktop installation instructions for dimensions of
cooktop, countertop cut-out, and cabinet requirements. The
DD0130SS can be installed in most standard 30" wide cabinets,
(DD0136SS can be installed in most standard 36" wide cabinets),
(DD0148SS can be installed in most standard 48" wide cabinets).
Cooktop depth can vary greatly from one to another. This may
cause the fit of these two appliances to be rather tight.
Pay special attention to the 4 areas of potential interference
highlighted above. A countertop with (A) a raised lip and/or (B)
a backsplash, may not allow enough flat countertop for a proper
installation. The back of the downdraft cut-out will be 1¾" from the
cooktop and 2" of FLAT countertop is needed behind cooktop.
FRONT TO BACK
INSIDE CABINET DEPTH
DOWNDRAFT
B
A
COUNTER TOP
2"
1 3/4 "
COOKTOP
The system will operate most efficiently when the ductwork does
not exceed 40 feet of equivalent duct. The chart above, shows
equivalent feet of elbows and transitions. The number of feet of
straight 3¼" x 10" or 6" duct plus the equivalent feet of elbows or
transitions to be used should equal 40 feet or less.
The equivalent feet of various roof and wall caps has been taken
into consideration. Do not include them in this calculation.
3¼" x 10" TO
6" RD.
TRANSITION
2 FT.
3¼" X 10"
90oELBOW
14 FT.
6" RD.
ELBOW
8 FT.
RIGHT
DISCHARGE
LEFT
DISCHARGE DOWN
DISCHARGE
(as shipped)
*
*
*Dimensioned from top
of countertop