J D Williams Henderson SG855 Series User manual

Assembly Instructions - Please keep for future reference
Width - 135.0cm
Storage Double Headboard
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 01709 534123
Please turn to back page for important information when contacting Customer Helpline.
Dimensions
Depth - 16.0cm
Height - 110.0cm
Rev A - 08/11/2018
007 xx 8741

Important - Please read these instructions fully before starting assembly
Safety and Care Advice
Check you have all the
components and tools listed on
pages 2 and 3.
Remove all fittings from the
plastic bags and seperate them
into their groups.
Keep children and animals
away from the work area, small
parts could choke if swallowed.
Make sure you have enough
space to layout the parts before
starting.
Do not stand or put weight on
the product, this could cause
damage.
Assemble the item as close
to its final position (in the same
room) as possible.
Assemble on a soft level
surface to avoid damaging the
unit or your floor.
Parts of the assembly will be
easier with 2 people.
We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
Care and maintenance
Always lift furniture when
moving it (do not drag)
otherwise the joints may be
damaged.
From time to time check that
there are no loose screws on
this unit.
This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
1
Dust surfaces with a soft, dry,
lint free cloth.
More stubborn marks can be
removed using a damp
(not wet) cloth. Wipe the
surface dry immediately
using a soft lint free cloth.
Do not use detergents, abrasive
cleaning products or cleaning
products that contain ammonia,
solvents or silicone as these
may damage the surface finish.
To protect the furniture,
position the furniture out of
direct sunlight and away from
direct heat sources such as
radiators and fires.
Do not place the furniture in
excessively dry and humid
conditions.
Do not place hot or cold
objects on the surface, always
use protective mats to avoid
marking the furniture.
Clean spills up immediately
Dispose of all packaging
carefully and responsibly
when assembly complete.
Do Not dispose of packaging
until assembly complete.

Please check you have all the panels listed below
Components -Panels
2
Important - Thick lines indicate finished edges
Top (135.0x16.0cm)
2411
Front Rail (135.0x84.0cm)
2414
Back Rail (131.6x22.8cm)
2413
Shelf (135.0x16.0cm)
2412
Left Back Panel
(84.0x25.0cm)
2404
Divider x 2 (22.8x13.8cm)
2407
Right Back Panel
(84.0x25.0cm)
2410
Left End Panel
(22.8x15.8cm)
2406
Right End Panel
(22.8x15.8cm)
2415
Back Rail x 2
(84.0x12.6cm)
2405
Shelf x 6 (12.6x22.8cm)
2408

3
70 80 90 100 110 120
010 20 30 40 50 60
mm
130 140 150 160 170
Ruler - Use this ruler to help correctly identify the screws
Please check you have all the fittings listed below
Components-Fittings
Note: The quantities below are the correct amount to complete the assembly, In some case more fittings
may be supplied than are required.
Tools required
If you have damaged or missing components, call the
Customer Helpline: 01709 534123 Please turn to back page
for important information when contacting Customer Helpline.
Cross headed screwdriver
(medium & large ) Tape Measure
Large cam x 39
Code 760001103
Metal dowel x 39
Code 760003004
ABC
E
Drill
DF
12mm screw x 2
Code 690001099
Support bracket x 1
Code 760001901
Assembly Screw x 26
Code 690001075
Stick on cam cover x 8

Exploded View
4
2411
2412
2406
2413
2407
2407
2405
2405
2404
2408
2408
2408
2408
2408
2408
2414
2415
2410

Step 1
Assembly Instructions
5
Fittings you will need for this step:
A
x6
Fittings you will need for this step:
Fitting cams to back
rail.
Step 2
Note: Insert metal
dowels as far as
shown by arrows.
Do not over tighten.
B
Fitting dowels and
cams to front rail.
B
Note: Ensure cam
arrow points towards
the edge with hole.
A
B
x18
A
x3
B
B
B
BB
B
B
B
B
B
B
B
B
B
B
B
B
B
A
A
A
2414
2413
A
A
A
A
A
A

Step 3
Assembly Instructions
6
Step 5
Step 4
Fitting cams to
back panels.
A
x4
A
x12
Fitting cams to 6
shelf panels.
A
A
A
A
A
A
2404
2408
A
A
2408
A
A
2408
A
A
2408
A
A
2408
A
A
2408
2410
Fittings you will need for this step:
Fittings you will need for this step:

Assembly Instructions
7
Step 5
Fitting cams to
back rails.
Step 6
Fitting cams to end
panels and dividers.
A
x6
A
x8
A
A
A
2405
A
A
A
A
A
A
A
A
A
A
A
2405
2406
2415
2407
2407
Fittings you will need for this step:
Fittings you will need for this step:

Step 7
Assembly Instructions
8
Step 8
Step 9
Fittings you will need for this step:
Fitting dowels and
cams to top panel.
Fitting dowels and
cams to underside
of shelf panel.
Fitting dowels and
cams to top side
of shelf panel.
B
x11
Fittings you will need for this step:
B
x7
Fittings you will need for this step:
B
x3
B
B
B
B
B
BB
B
BB
B
B
B
B
B
B
B
B
B
B
B
NOW TURN SHELF PANEL OVER
Finished edge
We reccomend placing
this panel on the
packaging the unit came in
when inserting these
fittings to avoid damage
to your floor.
2411
2412
2412
Finished edge
Finished edge

Step 10
Assembly Instructions
9
Connect the dowels in
the top panel with
the cams in the end
panels and divider panels
& .
Attach end panels &
dividers the top panel.
Step 11
2406 2415 2407
2411
2406
2407
2407
2415
Finished edge
Finished edge
Finished edge
Finished edge
Finished edge
Finished edge
Finished edge
Turn cam 180 degrees
to lock
A
Connect the dowels in
the top panel with
the cams in the back rail
.
Attach back rail the
top panel.
2413
2411
Turn cam 180 degrees
to lock 2413
2411
2411

Step 12
Step 13
Assembly Instructions
10
Finished edge
Connect the dowels in
the shelf panel with
the cams in the back rail
.
Attach shelf panel to
the back rail.
2413
2412
Turn cam 180 degrees
to lock
Secure the shelf
panel to the end and
divider panels.
Using screws
secure the shelf panel
to the ends and
divider panels
& .
2412
2406
2415 2407
C
x8
C
2413
2412
2406
2407
2407
2415
2412
C
C
C
C
C
C
C
C
Fittings you will need for this step:

Assembly Instructions
11
Step 14
2412
2402
2414
2402
2414
2408
2408
2408
2408
2408
2408
Connect the dowels in
the shelf panel with
the cams in the front rail
.
Attach front rail to the
shelf panel.
2414
2412
Turn cam 180 degrees
to lock
Connect the dowels in
the front rail with
the cams in the shelves
.
Attach shelf panels
to the front rail.
2408
2414
Turn cam 180 degrees
to lock
Step 15

Assembly Instructions
12
Step 16
Connect the dowels in
the front rail with
the cams in the back rails
.
Attach back rails
to the front rail.
2405
2414
Turn cam 180 degrees
to lock
Connect the dowels in
the shelf panel to the
cams in the back panels
& .
Attach back rails
to the front rail.
2404 2410
2412
Turn cam 180 degrees
to lock
2414
2405
2405
cam holes to inside
2412
Step 17
2410
2404

Assembly Instructions
13
Step 18
Secure the back panels
to the shelves end and
back rail panels.
Using screws
secure the back panels
& to the
shelves & back
rails .
Please ensure screws
locate into the grooves
on back rails & shelf
panels.
2404 2410
2405
2408
C
x18
C
C
C
C
C
CC
C
CC
C
C
C
CC
C
C
C
C
Fittings you will need for this step:
2410
2404
2408
2408
2408
2408
2408
2405 2408
2405

Assembly Instructions
14
Step 19
Congratulations!
Your unit is complete
We recommend that this
unit is fixed to a suitable
wall to prevent possible
overbalancing. We have
included a fixing bracket
for this. No fixing screws
are provided as they will
need to suit the wall
type, and the length of
screw will depend on
the distance from the
back of the unit to the
wall. Please ensure
fixings used are
appropriate to your wall
type. Locate the bracket
to the top panel or to the
end panel as close to
top as possible. We do
not specify exact
location for the bracket,
this is left to the
customer’s discretion.
D
E
Fixing to wall
Please take care when
drilling into the wall,
avoiding any pipes and
wires. Wear safety
goggles when drilling.
The use of residual
current device (RCD) is
recommended when
working with tools.If in
doubt consult a
qualified person.
Warning:
2 people to lift.
Lift with care.
With help move the
unit into position.
Warning:
x1
x2
x8
IN ORDER TO PREVENT OVERTURNING
THIS PRODUCT MUST BE USED WITH
THE WALL ATTACHMENT DEVICE
PROVIDED
Serious or fatal crushing injuries can occur from
furniture tipping over. To help prevent topple over:
An attachment device is provided with your
product. However you will need to source
suitable fixings for your wall type. If in doubt,
please consult a qualified trades person.
Always ensure the wall to be drilled is free
from hidden electrical wires, water and gas
pipes.
Use the wall attachment device provided.
Never allow children to climb or hang on
drawers, doors or shelves.
Place heaviest items in the lower drawers
or shelves.
Unless specifically designed to accomodate,
do not set TV’s or other heavy objects on
top of this product.
Never open more than one drawer at a time.
WARNING
F
F
Attach cam cover stickers
to exposed cam fixings
on ends & dividers
cam stickers

Assembly Instructions
Congratulations! Your unit is complete.
Important Information
If you need help or have damaged or missing parts, call the Customer Helpline:
01709 534123 8am - 4.30pm (Monday toThursday)
8am - 2.30pm (Fridays)
Please have the following information to hand:
>> Unit Description
>> Product Code
>> Product Colour
>> Place of Purchase
>> Catalogue Ref. No.
>> Item Code
>> Assembly Instructions
You can also e-mail your requests to us at:
[e-mail]
Alternatively, you can write to us at: Customer Service Department, Addspace Furniture Limited,
Braithwell Way, Hellaby Industrial Estate, Hellaby, Rotherham, South Yorkshire, S66 8QY.
We do have an answer machine should you contact us out of office hours, so in addition to
the above information could you leave your name, address, daytime telephone number and
the nature of your call on the answerphone. All calls will be actioned asap.
(by contacting the customer service line your statutory rights are not affected)